Panasonic Wv Np472 Operating Instructions Manual

-31-
■Camera Setup Menus
Menu windows are shown in this page. Refer to page
16 for menu operations. 

-32- Setup windows listed below are accessible only from
the PC. Operations in these windows are described in
the following pages.
Click any of the setup selection buttons on top of the
screen to open the desired window.
The following are opened from the Network Setup win-
dow.
Image Setup
Alarm Setup
FTP Client Setup
User Authentication Setup
Host Authentication Setup
System (Date & LED) Setup
■Image Setup
1. Open the Image Setup window.
2. Select the parameter for each item.
Refresh Interval:Fast,...

-33- 3. E-Mail Notice Setup
•Select ON or OFF for E-mail Notice.
ON:Sends an e-mail when an alarm operates.
OFF:Does not send.
•Enter the e-mail server address.
A hostname.domainname can be entered
when using the DNS function.
•Enter the sender name. The default setting is
NW_camera.
•Select ON or OFF for Attach Image.
ON:Attaches the image data to an e-mail.
OFF:Does not attach.
•Click the SET & REBOOT button.
•Enter a maximum of 4 destination addresses,
and click the SET button. 
•Click the DEL...

-34- •Enter a file name and click a radio button.
Fix: Uses repeatedly a single file name when
overwriting new data.
Date & Time:Creates and attaches a serial
number and a date-and-time to the
entered file name.
•Set a transmission interval.
Available time (seconds):0.2 - 0.9, 1 - 1 440
Available time (minutes):1 - 1 440
Notes:
•Transmission interval may be delayed depend-
ing on the network speed and/or traffic condi-
tions. 
•The alarm image precedes the non-alarm
image in transmission to the FTP...

-35-
■Host Setup
Note:Never turn over the order: start with the host reg-
istration, and then proceed to the authentication
ON/OFF.
1. Open the Host Setup window.
2. Host Registration
•Enter the IP address of the PC.
A hostname.domainname can be entered
when using the DNS function.
•Select an access level, and click the SET but-
ton. The default setting is level 1.
1 (Administrator):Allows you to operate
setup menus and to view live and record-
ed images.
2 (Live Only):Allows you to view live and...

-36- You can reset the following data back to the factory
default settings.
Camera Setup
Setup Menu (PC oriented)
HTML files
■Initializing the Camera Menu
•Move the cursor to CAMERA RESET.
•Hold down simultaneously 
Land Mbuttons for
2 seconds on the camera, or click the All Reset
button on your computer display.
■Initializing the Setup Menu
•In the power-on state, press the side panel buttons,
Jand Ksimultaneously while holding down the
rear panel button A.
Hold down the button A for 6 seconds. It will...

-37-
VIEWING PICTURES
■Image Quality Selection
1. Click the Setup Menu button in the main page.
The Network Setup window opens.
2. Click the Image button in the menu bar lined on top
of the screen.
The Image Setup window appears.
3. Select the parameters.
Refresh Interval:Fast, Middle, Slow, Very Slow
Image Capture Size (pixels):640x480, 640x240*,
320x240, 160x120
Quality of Image:Super Fine, Fine, Normal, Rough
Bandwidth Control (kbps):32, 64, 128, 256, 512,
1 024, Unlimited
*: The 640 x 240 selection...

-38-
■Monochrome Mode
You can switch the camera between the color mode
and black-and-white mode. This may help picture
become clear under conditions of insufficient lighting.
1. In the main page, click the Camera Menu button.
2. The Day & Night button appears in the lower-left of
the screen.
ON:Selects black-and-white mode.
OFF:Selects color mode.
AUTO:Selects color mode when picture is bright
enough, or black-and-white mode when it is
dark.
3. Click ENTER.
4. Click the Return button to go back to the...

-39- When an alarm sounds, the camera performs output
functions depending on the setup.
Inputs: 
•The alarm sensor connected to the ALARM IN ter-
minal on the camera
•The built-in VMD (Video Motion Detector) that
detects a motion in video by monitoring the speci-
fied area
Outputs:
•“Alarm” display appears in the upper right corner
of the main page.
•The picture files as an alarm sounds are stored in
the camera.
•An e-mail notifies the specified addresses of the
alarm activation with or without a picture...

-40-
■Canceling Alarm Display
“Alarm” display in the upper right corner will disappear
when you operate the following.
•Click the Return button after once opening Alarm
List.
Or
•Click the Return button after opening any of setup
menus.
■VMD Setup
You can setup VMD (video Motion Detector).
●Detection Area Setup
1. In the main page, click the Camera Menu button.
The menu control buttons appear under the image
display area.
2. Click the Menu ON button. 
** SET UP ** will be overlaid on the camera...