Panasonic Wv Np472 Operating Instructions Manual

-21-
10. Special Menu
This menu lets you adjust and set up the video signal of
the camera to meet your requirements.
Move the cursor to RET in the bottom line of the CAM
SET UP menu and press Land Msimultaneously
(holding down Land press M) for 2 seconds or
more. The SPECIAL menu appears on the monitor
screen.
10-1. Camera Picture Upside Down Positioning
(UP SIDE DOWN)
1. Move the cursor to UP SIDE DOWN.
2. Select ON when you want to turn the picture upside
down.
Note:The right and left of the picture...

-22- To reset to the factory settings (CAMERA RESET)
1. Move the cursor to CAMERA RESET. PUSH SW is
highlighted.
2. While holding down Land M, hold down I
for 2 seconds or more. The camera is reset to the
factory settings.
NETWORK SETUP
Set up network parameters when connecting the
10/100BASE jack with a network.
Notes:
•Access the setup menu from the PC to use the
DHCP or DNS server, because these settings are
not included in this window.
•Ask your system administrator or ISP (Internet
Service Provider)...

-23-
SETUP FROM THE PC
PREPARATIONS FOR THE PC
■Connections
Prior to connections, specify the connection type and
prepare relevant devices and cables.
Notes:
•We recommend that you use connection type 1 or
type 2 when setting up the network address of the
camera.
•Be sure to unplug or switch all the devices off, then
start connections.
●Direct Connection to PC (Type 1)
Use a cross-type network cable in the category 5 to
connect the camera directly with the PC.
Necessaries: Cross-type network cable...

-24-
■Network Setup of the PC
To set up the network of the PC, first change the TCP/IP
settings of the PC to match them to the default settings
of the camera. 
The following are the default network settings of the
camera.
IP address : 192.168.0.10
Subnet mask : 255.255.255.0
Default gateway : 192.168.0.1
To access the camera, the IP address of the PC should
be “192.168.0.XXX” (where XXX should be a number
from 2 to 254 except 10).
Note:The following procedure is described based on
the assumption that the...

-25- 6. Click “Internet Protocol (TCP/IP)”, and then click
the [Properties] button.
7. Click the “Use the following IP address” radio but-
ton and enter the IP address and the subnet mask
as follows.
IP address : 192.168.0.9
Subnet mask : 255.255.255.0
8. Click the [OK] button, and the window dialog box
closes.
■Network Setup of the Camera
On completion of the network setup of the PC, begin
the network setup of the camera. If multiple cameras
are connected, it is required to set up each camera...

-26- 3. Click the Setup Menu button. The User Setup win-
dow appears.
•Enter “admin” in the user name column.
•Click the OK button.
■Network Setup Parameters vs. Connection Type
Connection type Item Description of the parameter
Connection type 1 IP address Enter “192.168.0.XXX” for the IP address (where XXX should
be a number from 2 to 254 except the same IP addresses
already assigned to the PC and any other cameras).
Subnet mask Use the default setting “255.255.255.0” for the subnet mask.
Default...

-27-
Connection type 2 IP address Set the IP address designated by your network administrator.
However, the setting is not required if DHCP is used in an
intranet.
Subnet mask Set the subnet mask designated by your network administra-
tor.
However, the setting is not required if DHCP is used in an
intranet.
Default gateway Set the IP address of the default gateway designated by your
network administrator.
However, the setting is not required if DHCP is used in an
intranet.
Network speed Set the network...

-28-
Secondary server Set the IP address of DNS when using the DNS server.
Refer to your internet Internet service provider for the IP
address of the DNS. Primary and secondary IP addresses
can be set for the DNS.
DHCP Set to ON if your internet Internet service provider uses a
DHCP server (the DHCP server assigns an IP address to the
camera automatically) after confirming that your internet
Internet service provider uses a DHCP server.
Connection type 4 IP address The setting differs depending on the...

-29-
Host name Refer to your Internet service provider and set the designated
host name if required.
DNS Set to ON when using the DNS server.
Primary server No setting required
Secondary server Set the IP address of DNS when using the DNS server.
Refer to your internet Internet service provider for the IP
address of the DNS. Primary and secondary IP addresses
can be set for the DNS.
DHCP Set to ON if the router uses DHCP. 

-30-
CAMERA SETUP FROM THE PC
The camera setup menus overlaid on the camera pic-
ture appear by clicking the Camera Setup button in the
main page. You will be prompted by authentication dia-
log box. Enter “admin” in the user column if you have
not registered it yet, or enter the registered user name
and password if user authentication is applied. Menu
control buttons are lined in the lower part of the screen.
Note:The following pages mainly describe the unique
setup operations of the PC. Refer to PRIOR...