Home
>
Panasonic
>
TV Video Accessories
>
Panasonic Video Multiplexer Wj Fs616 Operating Instructions
Panasonic Video Multiplexer Wj Fs616 Operating Instructions
Have a look at the manual Panasonic Video Multiplexer Wj Fs616 Operating Instructions online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
-29- 4. Press the SET button to move the cursor to the
recording mode title area. The square cursor
appears in the character table.
5. To select a character, move the cursor on the
desired character in the table by pressing the
Direction Arrow buttons.
6. Press the SET button to pick up the character
and place it in the title area.
7. Repeat the above procedures 5 to 6 to set the
title.
8. If a wrong character is selected, press the
Increment (+) or Decrement (–) button to move
the cursor in the title area.
Note:Press the (+) button to move the cursor to
the right, or press the (–) button to move the
cursor to the left.
Then press the SET button to overwrite the
character with the character selected from
the table.
9. Press the SETUP/ESC button. The cursor moves
to MODE number.
10. Repeat the above procedures 1 to 9 to assign
the other MODE numbers.
11. After completing the setting, press the SET
UP/ESC button to return to the REC OUTPUT
SETUP menu.
After finishing the setting, press the SETUP/ESC
button to return to the previous SETUP MENU.
Multiscreen 2 Output Setup
These items let you select the mode when connect-
ing the Record Output (REC OUT) to the monitor for
Multiscreen 2 Monitor.
WJ-FS616 SETUP MENU
ALARM SETUP *
MULTI OUTPUT SETUP *
SPOT OUTPUT SETUP *
REC/MULTI2 MULTI2 OUTPUT *
SYSTEM SETUP *
CAM DOWNLOAD NO
CAM UPLOAD NO
ALL RESET SELECT *
1. Move the cursor to the REC/MULTI2 parameter
on the SETUP MENU.
2. Select MULTI2 OUTPUT by pressing the LEFT
or RIGHT button, then press the SET button.
The MULTI2 OUTPUT SETUP menu appears on
the monitor screen as shown below.
MULTI2 OUTPUT SETUP
DISPLAY POSITION *
SEQUENCE MODE SEQ2
1. Camera Display Position
This item lets you select the position where the
camera picture will be displayed on the Multiscreen
Monitor 2.
1. Move the cursor to DISPLAY POSITION, then
press the SET button. The table shown below
appears on the monitor.
1 2 3 4
5 6 7 8
9 10 11 12
13 14 15 16
2. Move the cursor to the desired channel number
by pressing the UP or DOWN button.
3. Select the numbers of the cameras to be dis-
played by pressing the LEFT or RIGHT button.
The pictures of the selected cameras are dis-
played one after another on the monitor screen.
Note:Numbers can also be input directly with
the Camera Number Buttons (1 - 10).
4. After completing the setting, press the SET
UP/ESC button to return to the previous MULTI
2 OUTPUT SETUP menu.
Note:This operation only affects the camera
display positions.
It has no effect on the camera channel,
recording order or sequence order.
2. Sequence Mode
This item lets you select the sequence pattern for
display on the Multiscreen Monitor 2.
Refer to Sequence Setup on page 31 for more
details.
1. Move the cursor to the SEQUENCE MODE
parameter.
2. Select the desired mode by pressing the LEFT
or RIGHT button. The initial factory setting is
SEQ2.
SEQ1:Spot Sequence
SEQ2:Multi Sequence
SEQ3:Multi Sequence
After finishing the setting, press the SETUP/ESC
button to return to the previous SETUP MENU.
-30-
System Setup
Move the cursor to SYSTEM SETUP on the SETUP
MENU, then press the SET button. The SYSTEM
SETUP menu appears on the monitor screen as
shown below.
Press the FUNCTION button to display the next
page. Press this button again to return to the previ-
ous page.
1. Clock Setup
This item lets you set the current time and date.
1. Move the cursor to CLOCK SETUP, then press
the SET button to move the cursor to the editing
area.
2. Move the cursor to the area you want to edit by
pressing the UP or DOWN button, then select
the month or number by pressing the LEFT or
RIGHT button.
3. After finishing the setting, press the SETUP/
ESC button to move the cursor to CLOCK
SETUP.
Note:The date and time are updated when the
SETUP/ESC button is pressed.
SYSTEM SETUP 1 OF 2
CLOCK SETUP JAN 1.97 0:00
CLOCK POSITION *
TITLE SETUP *
TITLE POSITION *
SEQUENCE SETUP SEQ1 *
SEQ TIMING-MLT INT(TIME-ADJ)
SEQ TIMING-SPT INT
LOCK MODE ALL
SYSTEM SETUP 2 OF 2
CABLE COMP/VD2/DATA SETUP *
ALM TERMINAL SETUP *
PLAYBACK MODE FIELD
DATA MODE CU550A
RS-232C MODE VCR
COM PORT SETUP *
VCR IN SELECT VIDEO
DAISY MODE OFF
UNIT ADDR.SET 1
DEC11.96 12:00:00
CAMTITLE
WJ-FS616 SETUP MENU
ALARM SETUP *
MULTI OUTPUT SETUP *
SPOT OUTPUT SETUP *
REC/MULTI2 MULTI2 OUTPUT *
SYSTEM SETUP *
CAM DOWNLOAD NO
CAM UPLOAD NO
ALL RESET SELECT *
TITLE SETUP 1 OF 2
1CH 1------- 0123456789
2CH 2------- ABCDEFGHIJK
3CH 3------- LMNOPQRSTUV
4CH 4------- WXYZ
5CH 5------- abcdefghijk
6CH 6------- imnopqrstuv
7CH 7------- wxyz
8CH 8-------
¤=?#&()*
+,-./:;E
@
TITLE SETUP 2 OF 2
9CH 9------- 0123456789
10CH 10------ ABCDEFGHIJK
11CH 11------ LMNOPQRSTUV
12CH 12------ WXYZ
13CH 13------ abcdefghijk
14CH 14------ imnopqrstuv
15CH 15------ wxyz
16CH 16------
¤=?#&()*
+,-./:;E
@
2. Clock Display Position
This item lets you select the position where the
clock will be displayed on the monitor screen.
1. Move the cursor to CLOCK POSITION, then
press the SET button. The position setting menu
appears on the monitor screen as show below.
2. Move the clock position by pressing the
Direction Arrow Buttons.
Note:In the Multiscreen display with display of
the Record out signals, the clock display is
shifted one line from the preset position if
the Camera Title and the Clock are preset
to the same position.
3. Press the SETUP/ESC button to execute the
selection and return to the previous SYSTEM
SETUP menu.
3. Camera Title Setup
This item lets you edit the camera title to be dis-
played on the monitor screen.
Up to 8 alphanumeric characters can be displayed
on the monitor.
1. Move the cursor to TITLE SETUP, then press the
SET button.
The TITLE SETUP menu appears on the monitor
screen as shown below.
-31-
SEQ1(SPOT-SEQUENCE)SETUP 1 OF 2
AUTO SKIP OFF
DWELL TIME 2SEC
STEP CAM PRE TIME STEP CAM PRE TIME
1 1CH - 2SEC 9 9CH - 2SEC
2 2CH - 2SEC 10 10CH - 2SEC
3 3CH - 2SEC 11 11CH - 2SEC
4 4CH - 2SEC 12 12CH - 2SEC
5 5CH - 2SEC 13 13CH - 2SEC
6 6CH - 2SEC 14 14CH - 2SEC
7 7CH - 2SEC 15 15CH - 2SEC
8 8CH - 2SEC 16 16CH - 2SEC
Press the FUNCTION button to display the next
page, then press this button again to return to
the previous page.
2. Move the cursor to the channel you want to edit,
then press the SET button.
The cursor moves to the title area, and the square
cursor appears on the character table.
3. To select a character, move the cursor on the
desired character in the table by pressing the
Direction Arrow buttons.
4. Then press the SET button to pick up the char-
acter, and place it in the title area.
5. Repeat the above procedures 3 to 4 until the
title for a certain camera is completed.
6. If a wrong character is selected, press the
Increment (+) or Decrement (–) button to move
the cursor in the title area.
Note:Press the (+) button to move the cursor to
the right, or press the (–) button to move the
cursor to the left.
Then press the SET button to overwrite the
character with the character selected in the
table.
7. Press the SETUP/ESC button to move the cursor
to the channel number area.
8. Repeat the above procedures 2 to 7 for the rest
of the cameras.
9. Move the cursor to the channel area, then press
the SETUP/ESC button to return to the previous
SYSTEM SETUP menu.
4. Camera Title Display Position
This item lets you select the camera title position to
be displayed on the monitor screen.
Refer to the Clock Display Position Setting on page
30 for more details.
1. Move the cursor to TITLE POSITION, then press
the SET button. The position setting menu
appears on the monitor screen.
2. Move the title by pressing the Direction Arrow
Buttons.
Note:In the Multiscreen display with display of
the Record out signals, the clock display is
shifted one line from the preset position if
the Camera Title and the Clock are preset
to the same position.
3. Press the SETUP/ESC button to execute the
selection and return to the previous SYSTEM
SETUP menu.
5. Sequence Setup
This item lets you program the sequence pattern for
Spot or Multi Sequence.
You can either program a spot sequence (SEQ1) or
two multi sequences (SEQ2, SEQ3).
Spot Sequence (SEQ1)
This item lets you program or edit a Spot Sequence.
Up to 32 steps can be assigned in the table shown
below.
You can also enable the Auto Skip function to skip
any steps where no video signal is present.
The duration of each step is determined by the
Dwell Time setting.
The initial factory setting is sequential display of 16
camera pictures.
1. Move the cursor to the SEQUENCE SETUP
parameter on the SYSTEM SETUP menu.
2. Select SEQ1 by pressing the LEFT or RIGHT
button, then press the SET button. The setup
menu shown below appears on the monitor
screen.
Auto Skip
1. Move the cursor to the AUTO SKIP parameter.
2. Select ON or OFF by pressing the LEFT or RIGHT
button.
ON:Enables the auto skip function.
OFF:Disables the auto skip function.
Note:The AUTO SKIP function is not available
when playing back pictures.
Step Assigment
1. Move the cursor to the step number you want to
edit in the CAM area by pressing the Direction
Arrow button.
2. Select the desired camera or playback channel in
the CAM area by pressing the Increment (+) or
Decrement (–) button.
1 - 16:Camera Channel
P1 - P16:Playback Channel
–:Not Assigned
Notes:
•Pressing the Camera Number Buttons assigns
the camera channel directly.
•Any playback steps programmed in a
sequence are excluded from display on the
Spot Monitor and Multiscreen Monitor 2 due to
the way the system is designed.
3. Repeat the above procedures to assign other
steps.
-32-
SEQ1(SPOT-SEQUENCE)SETUP 2 OF 2
STEP CAM PRE TIME STEP CAM PRE TIME
17 - - 2SEC 25 - - 2SEC
18 - - 2SEC 26 - - 2SEC
19 - - 2SEC 27 - - 2SEC
20 - - 2SEC 28 - - 2SEC
21 - - 2SEC 29 - - 2SEC
22 - - 2SEC 30 - - 2SEC
23 - - 2SEC 31 - - 2SEC
24 - - 2SEC 32 - - 2SEC
SEQ3(MULTI-SEQUENCE)SETUP 1 OF 5
AUTO SKIP OFF
STEP 1 CAM
DWELL TIME 5SEC
AREA CAM PRE AREA CAM PRE
1 1CH - 9 - -
2 2CH - 10 - -
3 3CH - 11 - -
4 4CH - 12 - -
5 5CH - 13 - -
6 6CH - 14 - -
7 7CH - 15 - -
8 8CH - 16 - -
SEQ2(MULTI-SEQUENCE)SETUP 1 OF 5
AUTO SKIP OFF
STEP 1 CAM
DWELL TIME 3SEC
AREA CAM PRE AREA CAM PRE
1 1CH - 9 - -
2 2CH - 10 - -
3 3CH - 11 - -
4 4CH - 12 - -
5 - - 13 - -
6 - - 14 - -
7 - - 15 - -
8 - - 16 - -
Preset Position
1. Move the cursor to the step number you want to
edit in the PRE area by pressing the Derection
Arrow Buttons.
2. Select the desired preset position number in the
PRE area by pressing the Increment (+) or
Decrement (–) button.
Note:A preset position assigned to a step that has
been assigned to a playback channel is invalid.
3. Repeat the above procedures to assign other
steps.
Dwell Time
•Uniform Dwell Time
1. Move the cursor to the DWELL TIME parameter.
2. Select the desired dwell time by pressing the
LEFT or RIGHT button.
Dwell Time can be selected between 0SEC and
30SEC.
Note:If 0SEC is selected for dwell time, the
spot sequence is not activated.
•Individual Dwell Time
1. Move the cursor to the step number you want to
edit in the TIME area by pressing the Directon
Arrow buttons.
2. Select the desired dwell time by pressing the
Increment (+) or Decrement (−) button.
Steps for which a different dwell time has been
selected are marked “−” in the DWELL TIME
area. Previous settings made in the DWELL
TIME area become invalid.
Programming Steps 17 to 32
1. Press the FUNCTION button to display the next
page. The table shown below appears on the moni-
tor screen.
2. Program the sequence pattern for steps 17 to
32 as described for the previous page.
3. Press the FUNCTION button to display the pre-
vious page.
4. After finishing the setting, press the SET
UP/ESC button to execute the setting and return
to the previous SYSTEM SETUP menu.
Auto Skip
1. Move the cursor to the AUTO SKIP parameter.
2. Select ON or OFF by pressing the LEFT or RIGHT
button. The initial factory setting is ON.
ON:Enables the auto skip function.
OFF:Disables the auto skip function.
Note:The AUTO SKIP function is not available
when playing back pictures.
Camera / Playback
This item lets you select the camera or playback picture
to be displayed at each step.
1. Move the cursor to the STEP parameter.
2. Select CAM or PLAY by pressing the LEFT or
RIGHT button.
CAM:Enables display of camera picture.
PLAY: Enables display of playback picture.
Multi Sequence (SEQ2, SEQ3)
This item lets you program or edit a Multi
Sequence. Up to 5 steps can be assigned in the
table shown below.
You can also enable the Auto Skip function to skip
any steps where no video signal is present.
The duration of each step is determined by the
Dwell Time setting.
According to the initial factory setting, SEQ2 is dis-
played on four screen segments (quad) and SEQ3
on nine segments.
1. Move the cursor to the SEQUENCE SETUP
parameter on the SYSTEM SETUP menu.
2. Select SEQ2 or SEQ3 by pressing the LEFT or
RIGHT button, then press the SET button. The
setup menu shown below appears on the moni-
tor screen.
-33- Dwell Time 1. Move the cursor to the DWELL TIME parameter. 2. Select the desired dwell time by pressing the LEFT or RIGHT button. Dwell Time can be selected between 0SEC and 30SEC. Note:If 0SEC is selected for dwell time, that step will not be shown on the monitor screen. Display Channel Assignment 1. Move the cursor to the area number you want to edit in the CAM area by pressing the Direction Arrow buttons. 2. Select the desired camera or playback channel in the CAM area by pressing the Increment (+) or Decrement (–) button. 3. Repeat the above procedures to assign other area numbers. Note: The multiscreen pattern of each step is determined automatically as follows: •For example, if several camra channels are assigned to area numbers, the screen segmen- tation that will accommodate the highest area number will be selected. •Areas not assigned a camera channel, or assigned a channel to which no camera is con- nected, are displayed in black. •Pressing the Camera Number Buttons assigns the camera channel directly. Preset Position 1. Move the cursor to the area number you want to edit in the PRE area by pressing the Direction Arrow Buttons. 2. Select the desired preset position number in the PRE area by pressing the Increment (+) or Decrement (–) button. Notes: •When the STEP parameter in this table is on PLAY, it is not possible to select a preset posi- tion in the PRE area. •It is possible to assign the same camera chan- nel to multiple area numbers within a step. In this case, make sure to assign the same preset positions. Programming Steps 2 to 5 1. Press the FUNCTION button to display the next step. 2. Program the sequence pattern for steps 2 to 5 according to the procedures described above. 3. After completing the setting, press the SETUP/ESC button to execute the setting and return to the previ- ous SYSTEM SETUP menu. 6. Sequence Timing (Multiscreen) This item lets you select functions of devices con- nected to pin 26 of the ALARM/REMOTE Control Connector.One of these functions is input of the time adjust- ment signal from a VCR, the other enables external sequence switching for multiscreen output. 1. Move the cursor to the SEQ TIMING-MLT para- meter. 2. Select INT(TIME-ADJ) or EXT by pressing the LEFT or RIGHT button. INT:Advances a sequence by the Dwell Time that was programmed on the SEQUENCE SETUP menu. It enables input of the time adjustment sig- nal from a Time Lapse VCR. EXT:Enables external sequence switching. Notes: •If EXT is selected, time adjustment input from a Time Lapse VCR is disabled. •If EXT is selected, connect the external sequence switch to pin 26 of the ALARM/ REMOTE Control Connector. •The Mutiplexer accepts the time adjustment signal for 6 minutes, that is, 3 minutes before and 3 minutes after the exact time (For example, from 9:57:00 through 10:03:00. Time is adjusted to 10:00:00). 7. Sequence Timing (Spot) This item let you select between internal and exter- nal control for advancing the sequence on the Spot Monitor. 1. Move the cursor to the SEQ TIMING-SPT para- meter. 2. Select INT or EXT by pressing the LEFT or RIGHT button. INT:Advances a sequence by the Dwell Time that was programmed on the SEQUENCE SETUP menu. EXT:Advances a sequence by the input from pin 6 of the ALARM/REMOTE Control Connector. 8. Lock Mode This item lets you decide which buttons will be locked while the LOCK switch is in ON position. 1. Move the cursor to the LOCK MODE parameter. 2. Select ALL or VCR by pressing the LEFT or RIGHT button. Initially, the initial factory setting is ALL. VCR:Locks the VCR Control Buttons. ALL:Locks all the buttons. Note:The LOCK indicator only lights up when the LOCK switch is in ON position and LOCK MODE is set to ALL.
-34-
CABLE COMP/VD2/DATA SETUP 1 OF 2
CAM CABLE VD2 DATA
1CH S ON ON
2CH S ON ON
3CH S ON ON
4CH S ON ON
5CH S OFF OFF
6CH S OFF OFF
7CH S OFF OFF
8CH S OFF OFF
CABLE COMP/VD2/DATA SETUP 2 OF 2
CAM CABLE VD2 DATA
9CH S OFF OFF
10CH S OFF OFF
11CH S OFF OFF
12CH S OFF OFF
13CH S OFF OFF
14CH S OFF OFF
15CH S OFF OFF
16CH S OFF OFF
Press the FUNCTION button to display the next
page, then press this button again to return to
the previous page.
2. Move the cursor to the channel you want to edit
by pressing the Direction Arrow Buttons.
3. Select one of the parameters shown below in
the CABLE area by pressing the Increment (+)
or Decrement (−) button.
S:Up to 400 m (1 300 ft)
M:400 m (1 300 ft) to 700 m (2 300 ft)
L:700 m (2 300 ft) to 900 m (3 000 ft)
When using the RG-59/U, BELDEN 9259 or
equivalent cable.
Note:Set CABLE to S if no camera is connect-
ed to the channel.
4. Select ON or OFF in the VD2 area by pressing
the Increment (+) or Decrement (−) button.
Note:Select ON for a camera with VD2 capabil-
ity, otherwise select OFF.5. Select one of the parameters shown below in
the DATA area by pressing the Increment (+) or
Decrement (−) button.
ON:Communicates with the camera site by
multiplexed data.
1-16:Communicate with the camera site by RS-
485.
This number indicates the unit address of
the selected camera.
OFF:Disables communication with the camera
site.
6. Repeat the above procedures to edit other
channels.
7. Press the SETUP/ESC button to execute the set-
ting and return to the previous SYSTEM SETUP
menu.
Note:Installation of the WV-PB6164 Data Multi-
plex Boards is required for controlling more
than 4 cameras.
10. Alarm Terminal Setup
This item lets you edit the alarm input number cor-
responding to each channel.
1. Move the cursor to ALM TERMINAL SETUP on
the SYSTEM SETUP menu, then press the SET
button. The ALARM TERMINAL SETUP table
shown below appears on the monitor screen.
ALARM TERMINAL SETUP
NO. CAM PRE NO. CAM PRE
1 1CH - 9 9CH -
2 2CH - 10 10CH -
3 3CH - 11 11CH -
4 4CH - 12 12CH -
5 5CH - 13 13CH -
6 6CH - 14 14CH -
7 7CH - 15 15CH -
8 8CH - 16 16CH -
2. Move the cursor to the number you want to edit
by pressing the Derection Arrow Buttons.
3. Select the channel to be assigned in the CAM
area by pressing the Increment (+) or
Decrement (–) button.
Note:Channel numbers can also be input
directly with the camera Number Buttons.
4. Select the preset position number to be
assigned in the PRE area by pressing the
Increment (+) or Decrement (–) button.
5. Repeat the above procedures to assign other
terminal numbers.
6. Press the SETUP/ESC button to execute the set-
ting and return to the previous SYSTEM SETUP
menu.
Note:The same channel can be assigned to
multiple alarm terminals.
In this case, different preset positions can
be assigned, but when alarm occurs at
these positions, the camera moves to the
preset position where the most recent alarm
occurred.
9.Cable Compensation/VD2/ Data
This item lets you select the optimum setting for the
cable-loss compensator and whether to supply the
VD2 (sync) signal or control data to the camera.
Note:These settings will work only for the input
channels that have the multiplex feature with
the Data Mutiplex Board WV-BP6164 installed.
The boards are installed for input channels 1
through 4 at the factory. You can install boards
for other channels. For installations, see page
10.
1. Move the cursor to CABLE COMP/VD2/DATA
SETUP on the SYSTEM MENU, then press the
SET button. The CABLE COMP/VD2/DATA
SETUP table shown below appears on the mon-
itor screen.
-35-
11. Playback Mode
This item lets you select the ID code for playback of
recorded video tape.
1. Move the cursor to the PLAYBACK MODE para-
meter.
2. Select FIELD or FS10 by pressing the LEFT or
RIGHT button.
The initial factory setting is FIELD.
FIELD:Normal position.
FS10:Enables playback of a tape that is
recorded on the WJ-FS10.
12. Data Mode
This item lets you select an external controller from
the data port.
1. Move the cursor to the DATA MODE parameter.
2. Select CU550A or PC by pressing the LEFT or
RIGHT button.
CU550A:Enables control from the WV-CU550A
System Controller.
PC:Enables control from a PC.
The initial factory setting is CU550A.
13. RS-232C Mode
This item lets you select the RS-232C port for con-
trol of the VCR, or for external control of the system
from a PC.
1. Move the cursor to the RS-232C MODE para-
meter.
2. Select VCR or PC by pressing the LEFT or
RIGHT button.
VCR:Enables use as VCR control port.
PC:Enables use as external control port from a
PC.
The initial factory setting is VCR.
Note:Be sure to select PC on this menu if you
plan to use the REMOTE OUT connector for
controlling the VCR.
COM PORT SETUP
RS-232C DATA RS-485
DELAY OFF OFF OFF
BAUD RATE 9600 9600 19200
WAIT TIME OFF 100 OFF
DATA BIT 7 8 8
PARITY ODD EVEN NONE
STOP BIT 1 1 1
XON/XOFF - OFF OFF
FULL/HALF - - FULL
2. Move the cursor to the port you want to edit by
pressing the Direction Arrow Buttons.
3. Select the desired Delay Time in the DELAY
area by pressing the Increment (+) or
Decrement (–) button.
4. Select the desired Baud Rate in the BAUD
RATE area by pressing the Increment (+) or
Decrement (–) button.
5. Select the desired Wait Time in the WAIT TIME
area by pressing the Increment (+) or
Decrement (–) button.
6. Select 7 or 8 in the DATA BIT area by pressing
the Increment (+) or Decrement (–) button.
7. Select the desired Parity Check in the PARITY
area by pressing the Increment (+) or
Decrement (–) button.
8. Select 1 or 2 in the STOP BIT area by pressing
the Increment (+) or Decrement (–) button.
9. Select ON or OFF in the XON/XOFF area by
pressing the Increment (+) or Decrement (–)
button. (except RS-232C)
10. Select FULL or HALF Duplex in the FULL/HALF
area by pressing the Increment (+) or
Decrement (–) button. (RS-485 only)
11. Repeat the above procedures to edit other
ports.
12. Press the SETUP/ESC button to execute the set-
ting and return to the previous SYSTEM SETUP
menu.
14. Communication Port Setup
This item lets you set the parameters for communi-
cation between the ports and the connected appli-
ances.
1. Move the cursor to COM PORT SETUP, then
press the SET button. The COM PORT SETUP
table shown below appears on the monitor
screen.
-36-
15. VCR Input Select
This item lets you select the VCR input terminal.
1. Move the cursor to the VCR IN SELECT para-
meter.
2. Select VIDEO or S-VIDEO by pressing the LEFT
or RIGHT button.
VIDEO:Selects input from the VCR VIDEO ter-
minal.
S-VIDEO:Selects input from the VCR S-VIDEO
terminal.
The initial factory setting is VIDEO.
16. Daisy Mode
This item lets you select whether to have the video
signal connected to SPOT IN looped through to the
SPOT OUT connector (daisy-chain connection).
1. Move the cursor to the DAISY MODE parame-
ter.
2. Select ON or OFF by pressing the LEFT or
RIGHT button.
ON:Select this parameter if the Video
Multiplexer is daisy-chained.
OFF:Normal position.
The initial factory setting is OFF.
17. Unit Address
This item lets you assign a unit number for identifi-
cation when multiple Video Multiplexers are con-
nected in a system.
1. Move the cursor to the UNIT ADDR. SET para-
meter.
2. Select the desired unit number by pressing the
LEFT or RIGHT button.
The initial factory setting is 1.
After finishing the settings, press the SETUP/ESC
button to execute the settings and return to the pre-
vious SETUP MENU.
CAM DOWNLOAD
DOWNLOAD 1CH NO
CAM 1 2 3 4 5 6 7 8
DATA O+ - O+ - - N- + -
CAM 9 10 11 12 13 14 15 16
DATA - - - - - - - -
O:RESULT OK +:DATA EXISTENCE
N:RESULT NG -:DATA NOTHING
CAUTION:ALL ALARM INPUTS
HAVE BEEN DISABLED.
Camera Download
This item lets you save the camera setup data into
the memory of the Video Multiplexer.
If the setup contents of the camera should be lost
due to malfunctioning or replacement of a camera,
you can simply reload the data stored in the Video
Multiplexer.
1. Move the cursor to the CAM DOWNLOAD para-
meter in the SETUP MENU.
2. Select YES by pressing the LEFT or RIGHT but-
ton, then press the SET button
The CAM DOWNLOAD table shown below
appears on the monitor screen.
3. Select the channel you want to edit by pressing
the LEFT or RIGHT button.
1CH - 16CH:Enables storing of setup data for
the selected camera channel.
ALL:Enables storing of setup data for all cam-
era channels.
Note:Channel numbers can also be input
directly with the Camera Number Buttons.
4. Move the cursor to “NO” by pressing the UP or
DOWN button.
5. Select “YES“ by pressing the LEFT or RIGHT
button.
6. Press the SET button to begin loading. “NOW
LOADING” appears on the table.
To cancel loading, press the SETUP/ESC but-
ton.
7. When loading is finished, the result is displayed
for each channel.
8. Press the SETUP/ESC button, then system will
restart.
Note:Alarm is disabled while this menu is dis-
played.
-37-
CAM UPLOAD
UPLOAD 1CH NO
CAM 1 2 3 4 5 6 7 8
DATA O+ - O+ - - N- + -
CAM 9 10 11 12 13 14 15 16
DATA - - - - - - - -
O:RESULT OK +:DATA EXISTENCE
N:RESULT NG -:DATA NOTHING
CAUTION:ALL ALARM INPUTS
HAVE BEEN DISABLED.
ALL RESET SELECT
ALL-RESET NO
CAUTION:ALL ALARM INPUTS
HAVE BEEN DISABLED.
Camera Upload
This item lets you upload camera setup data from
the Video Multiplexer’s memory to a camera.
1. Move the cursor to the CAM UPLOAD parameter
in the SETUP MENU.
2. Select YES by pressing the LEFT or RIGHT but-
ton, then press the SET button.
The CAM UPLOAD table shown below appears
on the monitor screen.
3. Select the channel you want to edit by pressing
the LEFT or RIGHT button.
1CH - 16CH:Enables data uploading to a
selected camera.
ALL:Enables data uploading to all cameras.
Note:Channel numbers can also be input
directly with the Camera Number Buttons.
4. Move the cursor to “NO” by pressing the UP or
DOWN button.
5. Select “YES” by pressing the LEFT or RIGHT
button.
6. Press the SET button to begin the load. “NOW
LOADING” appears on the table.
To cancel loading, press the SETUP/ESC but-
ton.
7. When loading is finished, the result is displayed
for each channel.
8. Press the SETUP/ESC button, then system will
restart.
Note:Alarm is disabled while this menu is dis-
played.
All Reset
This item lets you restore the factory settings without
having to go through each individual menu.
1. Move the cursor to ALL RESET SELECT on the
SETUP MENU, then press the SET button. The
ALL RESET SELECT menu shown below
appears on the monitor screen.
2. Select “YES” by pressing the LEFT or RIGHT
button.
3. Press the SET button to execute the All Reset
function.
4. First “NOW RESETTING” appears, then “RESET
COMPLETED”.
5. Press the SETUP/ESC button to return to the
SETUP MENU.
Note: Alarm is disabled while the ALL RESET
menu is displayed.
-38- OPERATING PROCEDURES VCR CAM SPOT ENTRANCE STILL SEQUENCE MULTI SCREEN STILL MONITOR CONTROL FUNCTION Before starting the following procedures, all system components should be turned on. Then set the LOCK switch to the OFF position. Operating the Spot Monitor The following operations are available on the Spot Monitor. Displaying the Camera Picture 1. Single Spot 1. Press the SPOTbutton. The LED (green) on the button lights up. 2. Press a CAMERA (1 - 16)button to display a selected camera picture on the monitor screen. The LED on the selected CAMERA button lights up. 2. Spot Sequence 1. Press the SPOTbutton. The LED (green) on the button lights up. 2. Press the SEQUENCEbutton to activate the sequence (SEQ1) programmed. The LED on the SEQUENCE button lights up. Note:Refer to the Sequence Setup on page 31 for more details. 3. Press the SEQUENCEbutton to move one step for- ward in the sequence. 4. To cancel the sequence, press the respective CAMERAbutton again. The selected camera picture is displayed in spot mode. Operating the Multiscreen Monitor The following operations are available on the Multi- screen Monitor. Note:We recommend to use the Single Spot when displaying non-interlace pictures, for instance, the Menu screen of the WJ-SX550, to prevent picture disturbance. Displaying the Camera Picture 1. Single Spot 1. Press the MULTISCREENbutton. The LED (green) on the button lights up. 2. Press the VCR/CAMbutton to CAMposition (LED off). 3. Press a CAMERA (1 - 16)button to display a selected camera picture on the monitor screen. The LED on the selected CAMERA button lights up. 2. Single Still 1. Repeat the step 1 - 3 described above for Single Spot. 2. Press the STILLbutton to freeze the displayed pic- ture. The LED on the STILL button lights up, and the LED on the pressed CAMERA button starts to blink. The camera title and “STILL” (both blinking) alter- nate in the display. 3. To cancel the still picture, press the STILLbutton again. The selected camera picture is displayed in spot mode.