Panasonic Video Cassette Recorder Pv V4622 Operating Instructions

							31
 Auto Play
Insert a tape 
➛ ➛➛ ➛
➛ Power comes on,
➛ ➛➛ ➛
➛ Play starts if there is no record tab
(see p. 4).
 Auto Rewind
Play
Fast Forward
 Play Auto Eject
(Repeat Play must be off)
Play, 
➛ ➛➛ ➛
➛ Tape end, 
➛ ➛➛ ➛
➛ Rewind,
➛ ➛➛ ➛
➛ Tape ejects if there is no record tab REW
FF PLAY
SEARCH
M/A SKIP
NUMBER
keys
CA/ZERO
Press ACTION
to return to normal screen. Press ACTION
to display menu.
Press to select REPEAT
PLAY and press 
to set ON or OFF.
Set to playback a recording over and over.
3 2 1
ON: Play repeats at
tape end or if
unrecorded
portion over 30
sec. is detected.
Press DISPLAY during play
to display Counter.
Press COUNTER
RESET at desired
position to reset to
“0:00:00”.
Continue to record, playback etc.
Press STOP.
Unit will go into FF
or REW mode and
stop at the last
point the Counter
was set to 0:00:00.
Press CA/ZERO
in Stop mode
to start ZERO
SEARCH.
5 4 3 21
To quickly return to a specified tape location.
VCR       C / A    CLOCK       CH
SELECT :              SET : 
EXIT      : ACT I ON     
REPEAT  PLAY             :OFF
T I ME  STAMP               :ON
REMOTE WARNING     :ON
AUTO  SHUT- OFF       :ON
AUTO  VCR/TV             :ONIDIOMA/LANGUE : ENGLISHVCR’ S  OUTPUT CH    :3
COUNTER
RESET
DISPLAY *Important:If a remote control button does not work when pressed, press
the VCR button on the remote and try the button again.STOP
ACTION
PLAY       1 2 : 0 0AM 0 : 0 0 : 0 0 SP
REW        1 2 : 3 0AM          CH  02 0 : 30 : 30 SP
SELECT/
SET
 :PLAY :STOP :FF
Zero Search
Repeat Play
Auto Operation Functions
STOP       1 2 : 3 1AM          CH  02 0 : 0 0 : 0 0 SP
Advanced
Operation
➛ ➛➛ ➛
➛ Tape end, 
➛ ➛➛ ➛
➛ Rewind
V4622 P22-44 (2nd) [LSQT0509B].p65 2002/05/23, 18:2931 
						

							32For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
5 43 2 1
Press to enter CAPTION
and press 
 to
set.
Channels already set and channels deleted
from Channel Memory are not displayed.
You can set a total of ten channel captions.
Do “Preset Caption” steps 1~3 on
left.
Characters
change in
following order.
Repeat steps 3 and 4 as desired.
To make corrections,
Press 
  to move to the incorrect entry,
then press  to make correction.
Or, press ADD/DLT to clear the caption.
A    B    C         Z    BLANK             &
9         2    1    0    /     !
Press to select MANUAL
CAPTION and
press 
 to set.
VCR  C / A   CLOCK     CHANNELPRESET  CAPTION
MANUAL  CAPTION
SELE
CT :              SET : 
EXIT      : ACT I ON     
VCR  C / A   CLOCK     CHANNEL
CH  NUMBER          CAPTION
        
02                     ----           
CLEAR    : ADD/DLT
SELECT  :              SET : 
EXIT       : ACT I ON     
Press  to
select CH
NUMBER
and press 
 to
move cursor to
the right.
Press ACTION twice
to return to normal screen.
Special VCR  Features
Repeat step 5 until
the list is complete.To create your
own captions, go to
“Manual Caption”
on right.
Channel Caption
When set, station name, e.g. ABC, CBS, and channel number appear on-screen.
Set up to 24 preset captions, and/or 10 manually created captions.
You need a list of stations and the channel numbers you receive them on.
To make corrections,
Press  and  to select the channel number,
then press  to change, or ADD/DLT to
delete the number.
1) Press  to
highlight caption.
2) Press 
 to move
cursor to the right.
3) Press 
 to
select CH
number.
4) Press 
 to set.
54 32 1
SELECT  :               
EXIT       : ACT I ON     
REPEAT  PLAY             :OFF
T I ME  STAMP               :ON
REMOTE WARNING     :ON
AUTO  SHUT
- OFF       :OFF
AUTO  VCR/TV             :ONIDIOMA/LANGUE : ENGLISHVCR’ S  OUTPUT CH    :3
VCR       C / A    CLOCK       CH
ANTENNA  :   CABLE
AUTO  SET
CHANNEL  CAPTION
WEAK  SIGNAL   DISPLAY : OFF
CABLE/DSS  BOX  SET  UP
VCR  Plus+  CH  SET  UP
VCR  C / A   CLOCK     CHANNEL
SELECT   :               
EXIT        : ACT I ON     
VCR  C / A   CLOCK     CHANNELANTENNA  :   CABLE
AUTO  SET
CHANNEL  CAPTION
WEAK  SIGNAL   DISPLAY : OFF
CABLE/DSS  BOX  SET  UP
VCR  Plus+  CH  SET  UP
SELE
CT :              SET : 
EXIT      : ACT I ON     
VCR  C / A   CLOCK     CHANNELPRESET  CAPTION
MANUAL  CAPTION
SELE
CT :              SET : 
EXIT      : ACT I ON     
VCR  C / A   CLOCK     CHANNEL           ABC          --           CBS          --           FOX          --           NBC          --           A&E            --           FAM          --CLEAR    : ADD/DLT
SELECT  :             SET : 
EXIT       : ACT I ON     
Press ACTION*
to display menu.
Press 
 to select
CHANNEL.
Press 
to select
CHANNEL
CAPTION and
press 
 to set.
Press 
to select PRESET
CAPTION and
press 
 to set.
Press ACTION twice
to return to normal screen.
6
Assign preset
captions.
Preset CaptionManual Caption
VCR  C / A   CLOCK     CHANNEL
CH  NUMBER          CAPTION
        
02                       ----           
CLEAR    : ADD/DLT
SELECT  :              SET : 
EXIT       : ACT I ON     
V4622 P22-44 (2nd) [LSQT0509B].p65 2002/05/23, 18:2932 
						

							33
*Important:If a remote control button does not work when pressed, press
the VCR button on the remote and try the button again.
ACTION
ADD/ DLT SELECT/
SET
 :PLAY :STOP :REW :FF
If Multi-brand feature is used (p. 22), and this
feature is set to on, a warning appears whenever
an invalid key is pressed in TV, DSS, or Cable
mode.
321
Press ACTION
to display menu.
Press 
to select REMOTE
WARNING and
press 
 to set ON
or OFF.
If “OFF,” remote warning will not appear if
invalid key is pressed.
Press ACTION
to return to normal screen.
VCR       C / A    CLOCK       CH
SELECT :              SET : 
EXIT      : ACT I ON     
REPEAT  PLAY             :OFF
T I ME  STAMP               :ON
REMOTE WARNING     :ON
AUTO  SHUT
- OFF       :ON
AUTO  VCR/TV             :ONIDIOMA/LANGUE : ENGLISHVCR’ S  OUTPUT CH    :3
Remote Warning ON/OFF Feature
When set to ON, all operations except for timer
record and tape eject are prohibited. Useful for
households with small children.
To turn off,
repeat above.
VCR  LOCK  ACT I VATED
VCR  LOCK  OFF
VCR Lock cancels in 24 hours if clock is set.
To turn on,
hold down REC on
the VCR in Stop mode
with no tape inserted
for 7 sec.
(Please ignore the NO
CASSETTE warning.)
VCR Lock Feature
Advanced
Operation
REC
V4622 P22-44 (2nd) [LSQT0509B].p65 2002/05/23, 18:2933 
						

							34For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
To find out the present tape position and amount of tape remaining.
Tape position is displayed for VHS-C type Cassettes, tapes
under 30 minute long, and some other tapes, but the
position is not correct.
Tape remaining time display may not be
precise.
1
BEG I N                END
                                                SP
                                 R 120 M
 I  N.
“DETECTING TAPE POSITION” is displayed
only when a cassette is first inserted, and it
takes several seconds for correct tape
position to appear.
SELECT/
SET
TAPE
POSITIONACTION
Special VCR Features (continued)
Press ACTION again
to return to normal screen.
When “OFF” is selected,
the program data is
written on the tape, but
will not be displayed.
The VCR writes program data (see example below)
about the first 10 seconds of every recording.
The information is then displayed the first 10 seconds of
playback.
3 2 1
SELECT  :               
EXIT       : ACT I ON     
REPEAT  PLAY             :OFF
T I ME  STAMP               :ON
REMOTE WARNING     :ON
AUTO  SHUT
- OFF       :OFF
AUTO  VCR/TV             :ONIDIOMA/LANGUE : ENGLISHVCR’ S  OUTPUT CH    :3
VCR       C / A    CLOCK       CHPress ACTION*
to display menu.
VCR       C / A    CLOCK       CH
SELECT :              SET : 
EXIT      : ACT I ON     
REPEAT  PLAY             :OFF
T I ME  STAMP               :ON
REMOTE WARNING     :ON
AUTO  SHUT
- OFF       :ON
AUTO  VCR/TV             :ONIDIOMA/LANGUE : ENGLISHVCR’ S  OUTPUT CH    :3
Press to select TIME STAMP
and press 
 to set.
 :PLAY :STOP :REW :FF
VCR/TV
Time Stamp FeatureReady Checklist
Clock is set to correct time.
Record tab in place. (See p. 4.)
Tape Position and Tape Status Feature
Press TAPE POSITION
to return to normal screen.
2
The present tape position indication and
amount of tape remaining (according to
tape speed) is displayed.
DETECTING   TAPE   POSITION
Press TAPE POSITION
to detect current tape position.
This function cannot display
exact amount of tape
remaining for tapes 30
minutes or less, or for tapes
over 120 minutes in length.
Note 
One Touch
Recording
11 / 11 / 2001  SUNSUN12 : 0 0PMCH  0 8  ABC
Timer Recording11 / 11 / 2001  SUN12 : 0 0PM  -      1 : 0 0PM   CH  0 8  ABC   ABC    MOVIEMOVIE
When Clock is not
set...
SHUTTLE
Ring
V4622 P22-44 (2nd) [LSQT0509B].p65 2002/05/23, 18:2934 
						

							35
*Important:If a remote control button does not work when pressed, press
the VCR button on the remote and try the button again.
The VCR VCR/TV selection can be set to
auto or manual.
Press ACTION
to return to normal screen.
31
Press ACTION
to display menu.
SELECT  :               
EXIT       : ACT I ON     
REPEAT  PLAY             :OFF
T I ME  STAMP               :ON
REMOTE WARNING     :ON
AUTO  SHUT- OFF       :OFF
AUTO  VCR/TV             :ONIDIOMA/LANGUE : ENGLISHVCR’ S  OUTPUT CH    :3
VCR       C / A    CLOCK       CH
For more on VCR/TV selection, see “Record
one station, watch another” and “Select
channels at VCR” sections (p.15).
VCR/TV Selector Feature
Note
VCR       C / A    CLOCK       CH
SELECT :              SET : 
EXIT      : ACT I ON     
REPEAT  PLAY             :OFF
T I ME  STAMP               :ON
REMOTE WARNING     :ON
AUTO  SHUT- OFF       :ON
AUTO  VCR/TV             :ONIDIOMA/LANGUE : ENGLISHVCR’ S  OUTPUT CH    :3
The power shuts off at a preset time.
2 1
Press ACTION
to display menu.
Press 
to select AUTO
SHUT-OFF.
Press 
 repeatedly
to change shutoff
time as shown
below.
Auto Shut-Off Feature
Press ACTION
to return to normal screen.
3
OFF
2 Hours
6 Hours4 Hours
OFF(Manual):You select “VCR” or “TV”
mode using the VCR/TV
button on the unit or remote.
ON(Auto):“VCR” mode is automatically
set when VCR is turned on,
or in Play mode.
2
Press to select AUTO
VCR/TV.
Press 
 to set
ON or OFF.
VCR       C / A    CLOCK       CH
SELECT :              SET : 
EXIT      : ACT I ON     
REPEAT  PLAY             :OFF
T I ME  STAMP               :ON
REMOTE WARNING     :ON
AUTO  SHUT- OFF       :ON
AUTO  VCR/TV             :ONIDIOMA/LANGUE : ENGLISHVCR’ S  OUTPUT CH    :3
The shut-off countdown will not function
during Play or Record.
Note
When set to “ON,” picture is displayed
regardless of signal strength.
ON: Picture is displayed despite signal
condition and may be of poor quality.
OFF:Screen turns solid blue when signal is
weak or non-existent.
Selecting ON has no effect on connected
equipment with blue back feature.
Press ACTION
to return to normal screen.3 2 1
Press ACTION
to display menu.
Press 
 to select and
display CHANNEL.
Press 
 to select
WEAK SIGNAL
DISPLAY, and
press 
 to set ON
or OFF.
ANTENNA  :   CABLE
AUTO  SETCHANNEL  CAPTION
WEAK  SIGNAL   DISPLAY : OFF
CABLE/DSS  BOX  SET  UP
VCR  Plus+  CH  SET  UP
SELE
CT :              SET : 
EXIT      : ACT I ON     
VCR  C / A   CLOCK     CHANNEL
SELECT  :               
EXIT       : ACT I ON     
REPEAT  PLAY             :OFF
T I ME  STAMP               :ON
REMOTE WARNING     :ON
AUTO  SHUT- OFF       :OFF
AUTO  VCR/TV             :ONIDIOMA/LANGUE : ENGLISHVCR’ S  OUTPUT CH    :3
VCR       C / A    CLOCK       CH
Weak Signal Display ON/OFF Feature
Shuttle Variable Speed Search
Release the Shuttle mode.Press a function button such as : PLAY,
STOP, etc.
The VCR performs the function of the button
pressed.
When the SHUTTLE Ring is turned more
than half in Stop mode, normal Fast Forward
or Rewind will begin.
Some noise bars are normal during Shuttle
operation.
After 3 minutes in Still or Slow, the VCR will
go into Stop mode.
When the SHUTTLE Ring is released, the
VCR goes into Still mode. The SHUTTLE Ring allows you to smoothly
control the tape speed during special effects
playback in both forward or reverse.
Begin the forward or reverse search.Turn SHUTTLE Ring while in Play or Still mode.
The more you turn the Ring, the faster the
search speed will be.
Notes
Advanced
Operation
V4622 P22-44 (2nd) [LSQT0509B].p65 2002/05/23, 18:2935 
						

							36For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Copying Your Tapes  (Dubbing)
1Insert pre-recorded tape.
2
Insert blank tape with record tab.
Press REC, then PAUSE/SLOW
immediately to enter REC/PAUSE mode.
3
4Press PLAY to start dubbing.
Playing VCR starts playback.Press PAUSE/SLOW to start dubbing.
Recording VCR starts recording.
Press STOP to stop dubbing.
Caution: Unauthorized exchanging and/or copying of copyrighted recordings may be copyright infringement.
Playing (Source) VCRRecording (Editing) VCR
5
To Monitor Dubbing on Your TV
1Turn your TV on and tune to the Recording
VCR channel (CH3 or CH4).
2Set the VCR/ TV Selector on the Recording
VCR to “VCR.”
Dubbing tapes protected with Copy
Guard will result in poor quality
recordings.
Connection
Press STOP to stop dubbing. Press PLAY, then PAUSE/SLOW
immediately to enter PLAY/PAUSE mode.
The operation of steps 4 and 5 must be done on the
playing and recording VCRs at the same time.
VCRIN FROM ANT.
OUT TO TV
VIDEO OUT
AUDIO OUT
AUDIO INVCR
VIDEO INTV
VHF/UHF
R
LRLR
LR
1
2
Front of VCR
(Audio/Video In Terminals on
the front of VCR are available)
Connect VIDEO OUT terminal on Playing VCR to VIDEO IN terminal on Recording VCR. To
monitor the dubbing, also connect a TV as shown.
Connect “L” and “R” AUDIO OUT terminals on Playing VCR to “L” and “R” AUDIO IN
terminals on Recording VCR.
In place of a Playing VCR, you can use other equipment, such as a Camcorder.
Simply connect the unit’s Audio/Video outputs to the Recording VCR.
Press INPUT to set VCR Input mode to LINE1
for Video Input (Rear) or to LINE2 for Video Input
(Front). (See “Selecting the Input Mode” below.)
Selecting the Input Mode
Method 1: Press INPUT repeatedly.
Channel Number ↔ ↔↔ ↔
↔ LINE1 ↔ ↔↔ ↔
↔ LINE2
Method 2: Press  CH  / .
Display will change as below.
“L1” or “L2” lights on Multi-Function Display
(about 4 sec.) when LINE1 or LINE2 is selected.
LINE1:  For rear audio/video connection.
LINE2:  For front audio/video connection.
 VIDEO IN 2L-AUDIO IN2-R
1
23
125
LINE1(CABLE)69(TV)orLINE2
(Rear Connection shown.)
Note
V4622 P22-44 (2nd) [LSQT0509B].p65 2002/05/23, 18:2936 
						

							37
Power Source:120 V AC, 60 Hz
Power Consumption:
Power On
Approx. 23 watts
Power Off
Approx. 3.0 watts
Video Signal:EIA Standard NTSC color
Video Recording System:4 rotary heads helical
scanning system
Audio Track:1 track (Normal)
2 channel (Hi-Fi Audio
Sound)
Tuner:
Broadcast Channels:VHF 2 ~ 13, UHF 14 ~ 69
CABLE Channels:Midband A through I (14 ~ 22)
Superband J through W (23 ~ 36)
Hyperband AA ~ EEE (37 ~ 64)
Lowband A-5 ~ A-1 (95 ~ 99)Special CABLE channel 5 A (01)Ultraband 65 ~ 94, 100 ~ 125
Operating Temperature:5 °C ~ 40 °C (41 °F ~ 104 °F)
Operating Humidity:10 % ~ 75 %
Weight:2.7 kg (6.0 lbs).
Dimensions:430 (W) x 98 (H) x 242 (D) mm
16-15/16” (W) x 3-7/8” (H)
x 9-9/16” (D) inch
Playing older or damaged tapes may
eventually cause video heads to
become clogged.
Specifications
Use a soft cloth or dusting attachment
of a vacuum cleaner to remove dust
from the ventilation holes on the back
sides and bottom of the cabinet.
Plastic surfaces are easily scratched
and can be marred by alcohol and
various solvents. Avoid excessive use
of oil-based furniture polishes since
the materials used in the cabinet will
accumulate more dust.
We recommend using a nonabrasive,
antistatic cleaner and polisher.
Cleaning the VCR
Note:Designs and specifications are subject to
change without notice.
V I DEO  HEADS  MAYNEED  CLEAN I NGPLEASE   I NSERT  HEADCLEAN I NG  CASSETTEOR  REFER  TO  MANUAL
END               : PLAY
Cleaning Tape
Digital Auto Picture
Automatically controls the video output signal for
less noise depending on the tape condition.
Digital Auto Tracking
Continuously analyzes the signal and adjusts for
optimum picture quality.
Manual Tracking Control (to reduce picturenoise)
Use during Playback and Slow Motion mode to
reduce picture noise.
Press CH (TRACKING) 
/ on the remote
control or VCR until the picture clears up.
To return to Auto Tracking, press POWER off,
then on again a few seconds later.
V-Lock Control (to reduce picture jitter)
In Still mode, CH (TRACKING) / operate as a
V-Lock control.
Features for a Quality Picture
RRRRRRRR
VCR & Cassette Information
During playback, this
screen appears if
clogging is detected.
To remove screen,
press PLAY on the
remote or VCR.
Head Cleaning
For Your
Information
Video Head Clog Sensor
Use “dry” type head cleaning
cassette only. (Part No. NV-TCL30PT
is recommended.)
Follow cleaning tape instructions
carefully. Excessive use of tape can
shorten head life.
If head clog symptoms persist, contact
your nearest Factory Servicenter or
authorized Servicenter. (See page 41.)
V4622 P22-44 (2nd) [LSQT0509B].p65 2002/05/23, 18:2937 
						

							38For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Warning and Instruction Displays
OSD
If you attempt to set or
review a Timer
Recording and the
Clock is not set...
After a Timer Program
has been set...
If you press REC on
the remote control or
VCR, and a cassette is
inserted with no record
tab...
If you press PLAY, FF,
REW, or REC on the
remote control or VCR
without a cassette
inserted...
If you press POWER
or STOP during a
Timer Recording...
(visible in VCR
mode only)
If you press an invalid
key on the remote
while in CABLE/DSS
mode...
CautionPageCaution
22
23
35
PLEASE SET CLOCK BY
PRESSING ACTION KEY
CHECK CASSETTE
RECORD TAB
NO CASSETTE
OSD
 4
14
15 16 16
16
If you press an invalid
key on the remote
while in TV mode...
TURN VCR OFF
FOR TIMER RECORDING
TO CANCEL TIMER REC
PRESS POWER THEN
STOP KEYVIDEO HEADS MAY
NEED CLEANING
PLEASE INSERT HEAD
CLEANING CASSETTE
OR REFER TO MANUAL
END       :PLAY
VCR LOCK ACTIVATED 33
VCR Status & Clock Displays Function & Channel DisplaysBlank Tape/ No Video Signal
Indications
Whenever a blank section of a tape comes
up in Play mode, or when the selected
channel has no broadcast signal with the
Weak Signal Display Feature (p. 35) set to
OFF, the TV screen will turn solid blue.
On-Screen Displays (OSD)
REMOTE CONTROL IS SET
TO CABLE/DSS MODE
USE VCR :  VCR KEY
22
23
35 37
If head cleaning
becomes necessary
while playing back a
tape...
If you press a function
buttons other than
STOP/EJECT or
POWER while the VCR
is in VCR Lock mode...
To display or
remove overlay
at right,
➛ ➛➛ ➛
➛ press DISPLAY.
These displays will alert you to a missed
operation or provide further instructions.
Page
CH 0 8
REMOTE CONTROL IS SET
TO TV MODE
USE VCR : VCR KEY
When a function button is
pressed, e.g. PLAY, or you
change channels, a 5
second display appears.
(Some Station names may
also appear if Channel
Caption is set. See page 32.)
REC         1 2 : 0 0AM0 : 25ABC   -0 : 1 2 : 3 4 SPSTEREOSAPMONO
11/11/2001  SUN
12:00PM-    1:00PM
CH 08 ABC MOVIE
Function Status
Rec Time Remaining
(OTR mode only,
see p. 15.)Current TimeChannel
Caption
(See p. 32.)
Tape Speed
(See p. 4.) Broadcast Audio
Being Received
(See p. 25.)
Counter
Time Stamp Data
( See p. 34.)
 This is not displayed
in Rec mode.
V4622 P22-44 (2nd) [LSQT0509B].p65 2002/05/23, 18:2938 
						

							39
Before Requesting Service
Power
No power…
Recording & Playback
TV program cannot be recorded...
Timer recording cannot be performed…
There is no playback picture, or the playback
picture is noisy or contains streaks...
During special effects playback, picture may
contain some vertical jitter when using a TV
with an Automatic Vertical Hold Control...
VCR cannot be controlled...
Check the following points if you are having trouble with your VCR.
Correction
Completely insert Power Plug into an AC outlet.
Set POWER button to on.
Make sure power source is active.
Miscellaneous
Programs cannot be viewed on TV...
Video cassette cannot be inserted...
Video cassette cannot be removed...
Video cassette ejects when a recording is started
or the power is turned off for timer recording...
In Stop mode, the motor (CYLINDER)
continues to rotate...
Remote Control
VCR cannot be remote controlled...
ACTION and PROG/VCR+ buttons do not
respond...
If you cannot resolve the problem, please call the Customer Call Center for product
assistance at 1-800-211-PANA (7262).
To locate an authorized servicenter, please call toll free 1-800-211-PANA (7262).
or send e-mail to : [email protected]
Make sure VCR power is on.
Make sure Remote is in VCR mode.
Aim Remote Control directly at remote sensor on VCR. (P. 6)
Avoid any object blocking signal path.
Check Remote batteries. (P. 4)
Make sure VCR LOCK is set to off. (P. 33)
Exposing VCR remote sensor to direct fluorescent or outdoor
light may cause signal interference.
Check connections between VCR, external antenna, and TV.
Press VCR button for VCR mode. (P. 22)
Check Remote batteries. (P. 4)
Correction
Check connections between VCR, external antenna, and TV.
Check channel selections.
Make sure your antenna system (CABLE or TV) is correctly
set. (Channels [P. 12])
Make sure cassette record tab is intact. (P. 4)
Confirm that clock is set to current time and date.
Make sure Cable/DSS box (if used) is left on and tuned to
channel to be recorded.
Set recording start/stop times correctly. (P. 16)
Make sure VCR POWER button is pressed off. (P. 16)
Timer recording may not be performed or continued if a power
interruption occurs before or during a Timer Recording, even
after power is restored.
Select channel 3 or 4 on TV to match VCR output channel (3
or 4) (P. 8) or select LINE.
Set VCR/TV selector to “VCR.”
Adjust TRACKING control in either direction. (P. 37)
Try Head Cleaning. (P. 37)
Set TV’s Vertical Hold Control to MANUAL, then adjust.
Make sure VCR power is on.
Check Remote batteries.
Make sure VCR LOCK is set to off. (P. 33)
Make sure Remote is in proper mode. (P. 22)
Make sure Timer Recording is not in progress.
Correction
Make sure TV power is on.
Make sure TV is set to output of VCR.
Check connections between VCR, external antenna, and TV.
Set VCR/TV selector to “TV.” (P. 15)
Make sure proper signal source is selected.
Insert the cassette with window side up; record tab facing you.
Check if a tape is already in the unit.
Completely insert Power Plug into an AC outlet.
Make sure cassette record tab is intact. (P. 4)
To enable Quick play mechanism, the cylinder will rotate for
about 3 minutes. This reduces response time from Stop to
Play mode and from Play to Rewind Search mode.
For Your
Information
V4622 P22-44 (2nd) [LSQT0509B].p65 2002/05/23, 18:2939 
						

							40For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Panasonic VHS VCR  Products
Limited Warranty
Limited Warranty  Coverage
If your product does not work properly because of a defect in materials or workmanship,
Panasonic Consumer Electronics Company or Panasonic Sales Company (collectively
referred to as “the warrantor”) will, for the length of the period indicated on the char t below,
which starts with the date of original purchase (“warranty period”), at its option either (a)
repair your product with new or refurbished parts, or (b) replace it with a new or a
refurbished product. The decision to repair or replace will be made by the warrantor.
During the “Labor” warranty period there will be no charge for labor. During the “Par ts”
warranty period, there will be no charge for parts. You must mail-in your product dur ing the
warranty period. If non-rechargeable batteries are included, they are not warranted.
This warranty only applies to products purchased and serviced in the United States or
Puer to Rico. This warranty is extended only to the original purchaser of a new product
which was not sold “as is”.
Mail-In Service
For assistance in the continental U.S.A. in obtaining repairs please ship the product to:
Panasonic Services Company
Customer Servicenter
Suite B
4900 George McVay Drive
McAllen, TX  78503
For assistance in Puerto Rico call Panasonic Sales Company
(787) 750-4300 or fax (787)768-2910
When shipping the unit carefully pack and send it prepaid, adequately insured and
preferably in the original carton. Include a letter detailing the complaint and provide a day
time phone number where you can be reached.
IF REPAIR IS NEEDED DURING THE WARRANTY PERIOD THE PURCHASER WILL BEREQUIRED TO FURNISH A SALES RECEIPT/PROOF OF PURCHASE INDICATINGDATE OF PURCHASE, AMOUNT PAID AND PLACE OF PURCHASE.CUSTOMER WILL BE CHARGED FOR THE REPAIR OF ANY  UNIT RECEIVEDWITHOUT SUCH PROOF OF PURCHASE.
Limited Warranty
PANASONIC CONSUMER ELECTRONICS COMPANY,
DIVISION OF MATSUSHITA ELECTRIC
CORPORATION OF AMERICA
One Panasonic Way
Secaucus, New Jersey 07094PANASONIC SALES COMPANY,
DIVISION OF MATSUSHITA
ELECTRIC OF PUERTO RICO, INC.,
Ave. 65 de Infantería, Km. 9.5
San Gabriel Industrial Park,
Carolina, Puerto Rico 00985
Product or Part Name
All components of VCR
except item listed below
Video Tape (in exchange
for defective video tape)Parts
One (1) Year
Five (5) DaysLabor
Ninety (90) Days
Not Applicable
Limited Warranty continued on next page.
V4622 P22-44 (2nd) [LSQT0509B].p65 2002/05/23, 18:2940