Panasonic Video Cassette Recorder Pv V4622 Operating Instructions

							21
To Make Corrections,
press  repeatedly
to delete number, then
repeat step 3.
Press PROG/VCR+
button to display
PROGRAM.
Press PROG/VCR+
button to end program.
VCR Plus+ System Programming
Press  
to select display VCR
Plus+ screen.
Press NUMBER keys
to enter PlusCode number
and press PROG/VCR+
button to set.
Press 
to select ONCE,
DAILY(MON~FRI), or
WEEKLY record
frequency and press
PROG/VCR+ button to set.
Press 
to select category and
recording speed.
Press 
 to set.
7 32 1
4
5
6
Do normal Timer Record if...
PlusCode number is not listed for
program.
the program (e.g. sports event) may
run over set stop time.
See page 17 to:
cancel a timer recording in progress.
review, replace, or clear program
contents.
Important for DSS/Cable Box Users
When recording via DSS, the receiver
must be left on. When recording via
cable or antenna, DSS receiver must
be off.
When recording via a cable box,
leave box on and tuned to channel to
be recorded.
Do not overlap program times.
PlusCode numbers cannot be used to
program VCR to record DSS and
cable box channels.
Make each entry within 1 minute or
the VCR will exit setup mode.
Once VCR Plus+ channel setup is
done, channels stay in memory. If a
power interruption occurs, VCR Plus+
channel setup may be lost. Please do
VCR Plus+ channel setup again.
Obtain unlisted PlusCode numbers by
calling 1 - 900 - 454 - 7587. Call costs
about $.95 per minute.
Ready Checklist
Clock is set.
VCR Plus+ Setup is complete (see pp. 18 - 20).
VCR Plus+        PROG.         LIST
13  SAT  --:--  --:--   --TODAY
CATEGORY : N/A                 SLP DATE START
ST
OPCH
SELECT :              EXIT        : PROG 
Press PROG/VCR+
button again to exit.ADD/DLT NUMBER
keys
 :PLAY :STOP :REW :FF
POWER
SELECT/
SET
ACTION PROG/
VCR+
If the PlusCode number entered begins with “0,”
skip to step 5. Display in step 4 will not appear.
Press POWER off to set the timer.
(“TIMER” lights up on Multi Function Display.)*Important:If a remote control button does not work when pressed, press
the VCR button on the remote and try the button again.
Press ADD/DLT
to delete the program.
VCR Plus+        PROG.         LIST
SELECT :              END         : PROG 
DATE START
STOPCH
SLP
SET:
CATEGORY : N/A
SELECT RECORD SPEED
13  SAT    2:20P    3:20P   02TODAYABC
Notes
Timer
Recording
VCR Plus+        PROG.         LISTDT   START     STOP    CH   SPD13     2 : 00 P    3 : 20P   02    SLP--  -- : --    -- : --   --   --
--  -- : --    -- : --   --   --
--  -- : --    -- : --   --   --
CANCEL   : ADD / DLT SELECT   :              SET :EXIT         : PROG
VCR Plus+        PROG.         LISTENTER PLUSCODE NUMBER
USING  0 - 9  KEYS 
- 
SELECT   :               
EXIT        : PROG     
VCR Plus+        PROG.         LISTENTER PLUSCODE NUMBER
USING  0
 - 9  KEYS
BACKSPACE   :  END         : PROG     
1 
VCR Plus+        PROG.         LISTONCEDAILY(MON-FRI)
WEEKLY
SELECT   :               
END         : PROG     
ontinued)
V4622 P1-21 (2nd) [LSQT0509B].p65 2002/05/23, 18:2821 
						

							22For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Multi-Brand Control Feature
The Remote Control can be set to control some TV and
Cable box/DSS functions.
Find your TV and Cable Box/DSS Receiver Brand
Code Number on the following page.
Setup for TV control,
➛ ➛➛ ➛
➛hold down TV button,
➛ ➛➛ ➛
➛enter code with NUMBER keys.
Multi-Brand Control Setup
Confirm code entry,
➛ ➛➛ ➛
➛press POWER to turn selected unit on or off.
See table below for controllable functions in each mode.Setup for Cable or DSS control,
➛ ➛➛ ➛
➛hold down DSS/CABLE button,
➛ ➛➛ ➛
➛enter code with NUMBER keys.
If code number is 100 or greater,
➛ ➛➛ ➛
➛press 100 key, then other digits.
E.g., press 100 - 0 - 2 for 102.
3 1
Repeat setup after remote battery replacement.
Remote will not control every TV, cable box, or
DSS made by the manufacturer listed. If you get
no response, your particular unit cannot be
controlled. There are NO additional codes for the
products listed. If your product is not listed, then
the remote is not compatible with that product.
2
ModeUnitVCR TV
VCR
TV
All
VOL UP/DOWN
POWER, INPUT,
number  keys,
ENTER, CH
UP/ DOWN,
VOL UP/DOWN VCR/TV, PLAY,
STOP EJECT,
SAP/ Hi-Fi,
DISPLAY, FF,
REW, PAUSE/
SLOW, REC,
SPEED,
 CA/ZERO,
COUNTER
RESET, TAPE
POSITION After remote is set up, you can select VCR, TV, or DSS/
CABLE for the desired function.
Press VCR, or TV, or DSS/CABLE on the remote.
(Table below shows available unit buttons for each mode.)
CABLE/ DSS
Using Multi-Brand Control
CABLE/
DSSVOL UP/ DOWNPOWER, ENTER,
number keys
(except 100key),
CH UP/ DOWN
Not all functions listed may be controllable.
In TV or DSS/CABLE mode, it may be necessary to press ENTER after pressing
NUMBER keys for channel selection.
TV
DSS/
CABLE
NUMBER
keys POWER
ENTER
Notes
Notes
V4622 P22-44 (2nd) [LSQT0509B].p65 2002/05/23, 18:2922 
						

							23
Advanced
Operation
Due to changes in infra-red commands used by manufacturers, some brands have several
codes. If your unit does not respond to the first code, please try the next one.
Some TV, Cable Box and DSS Box brands require you to turn on the power manually.
Cable Box Brand Code Numbers
Panasonic ........................ 01, 02
Quasar............................. 01, 02
RCA ....................................... 03
GE ......................................... 03
Zenith.................................... 04
Magnavox.............................. 05
TV Brand Code Numbers
Sylvania ................................. 05
Sharp............................... 06, 07
Sony ...................................... 08
Toshiba.................................. 09
Sanyo.................................... 10
Fisher.................................... 10JVC ........................................ 11
Hitachi................................... 12
Mitsubishi ........................ 07, 13
Samsung............................... 14
Gold Star ................... 15, 16, 17
DSS Brand Code Numbers
Important Notes
Archer .........................44, 06, 01, 120, 05, 63, 126
Cableview................29, 09, 01, 63, 120, 44, 42, 30
                                                52, 04, 124, 126
Citizen...................44, 52, 30, 63, 42, 04, 124, 126
Curtis.....................................08, 09, 25, 61, 53, 87
Century ......................................44, 51, 75, 59, 126
Cabletenna ..................29, 09, 01, 63, 120, 44, 126
Cable Cinema..............29, 09, 01, 63, 120, 44, 126
Diamond......................29, 09, 01, 63, 120, 44, 126
Eagle.......................62, 40, 22, 13, 58, 20, 26, 107
Eastern...................................................28, 29, 130
Explorer ..................................08, 09, 25, 61, 53, 87
Gemini.....................................................30, 04, 124
General Electric......................................01, 57, 120
General Instruments . 01, 84, 83, 34, 03, 02, 04, 55
   65, 66, 67, 68, 120, 106, 121, 122, 115, 117, 118, 124
Gerrard ...............................................44, 51, 75, 59
GC Electronics ...............44, 42, 63, 29, 30, 52, 04
                                                           124, 126
Hamlin...............41, 14, 15, 28, 102, 104, 103, 130
Hitachi................................................................... 31
Jerrold..........01, 84, 83, 34, 03, 02, 04, 55, 65, 66
       67, 68, 120, 106, 121, 122, 115, 117, 118, 124
Jasco......................................................30, 04, 124
Macom................................................................... 31
Magnavox ......................................................26, 112
Matsushita.................................17, 16, 08, 87, 109
Movietime ......................32, 39, 42, 44, 126, 38, 40
Maestro ...........................................................74, 35
NEC ....................................................40, 19, 38, 32
NSC ....................................................40, 19, 38, 32
Novavision .............................08, 09, 25, 61, 53, 87
Next Level........... 01, 84, 83, 34, 03, 02, 04, 55, 65
                             66, 67, 68, 120, 106, 121, 122
Oak .................................................46, 11, 129, 101Oak Sigma.....................................46, 11, 129, 101
Panasonic ..................................17, 16, 08, 87, 109
Philips ...................23, 24, 20, 13, 07, 50, 128, 129
Pioneer ......................................................06, 05, 12
Pulsar ....................04, 42, 63, 44, 30, 52, 124, 126
Quest ........................................................06, 05, 12
Radio Shack...............................44, 51, 75, 59, 126
RCA ............................................17, 16, 08, 87, 109
Realistic .....................................44, 51, 75, 59, 126
Recoton ......................................44, 51, 75, 59, 126
Regal.................41, 14, 15, 28, 102, 104, 103, 130
Regency ..................................................28, 29, 130
Rembrandt.......44, 42, 63, 29, 01, 32, 39, 120, 126
Samsung ......................................42, 06, 32, 05, 40
Scientific Atlanta...................08, 09, 25, 61, 53, 87
Sheritech ............................................................... 27
Signal ............................................................26, 112
SL Marx.............42, 06, 32, 40, 43, 44, 52, 63, 126
Sprucer ......................................17, 16, 08, 87, 109
Standard Components ...............32, 39, 42, 44, 126
Stargate .............. 04, 42, 32, 40, 63, 44, 30, 52, 06
                                                          124, 126
Sylvania ..........................................................19, 18
Teknika ...........................................................74, 35
Telecaption ....................................................77, 127
Teleview.................................40, 19, 38, 32, 42, 06
Texscan ..........................................................19, 18
Tocom...................................34, 33, 01, 42, 66, 120
Toshiba ................................................................. 36
Unika........................... 44, 42, 63, 29, 01, 126, 120
Universal ..............................52, 43, 44, 63, 42, 126
Viewstar ..................62, 40, 22, 13, 58, 20, 26, 107
Videoway ..........................................07, 23, 50, 129
Vidtek.................................................................... 64
Zenith ...............................................07, 23, 50, 129
Toshiba .................................................................. 90
Hitachi/ Hughes ............................................... 91,  99
Primestar ............................................................... 92
Drake..................................................................... 93
Magnavox........................................................ 94, 95
Uniden............................................................. 94, 95Optimus........................................................... 94, 95
Panasonic .............................................................. 96
ProScan................................................................. 97
RCA ....................................................................... 97
SONY............................................................ 98, 105
V4622 P22-44 (2nd) [LSQT0509B].p65 2002/05/23, 18:2923 
						

							24For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
You Cannot
Advanced Connections
You Can
record and view
both scrambled
and unscrambled
channels if
additional
equipment is
added.
This connection
requires: two
converter boxes,
an A/B switch,
and a 2-way
splitter.view channel
other than the
one selected
for any type of
recording.
do a Timer
recording of a
channel unless
you select it at
the cable box.
view any
(including
scrambled)
channel.
use VCR Remote
Control to select
channels without
using Multi-brand
control feature.
Audio/Video Connection
If your TV has AUDIO IN and VIDEO IN terminals, you can connect your VCR to
them to receive higher quality picture and sound.
IN
VIDEO AUDIO
R
LOUT
IN FROM ANT.
OUT TO TV  AUDIO
IN 1
VHF/UHF
 R
 L
 VIDEO
OUTTV
IN 2 IN 1
CABLE BOX
OUT INOUT 2 OUT 1
2-Way Splitter
CABLE BOX
OUT
A/B Switch
VCR
ANT
or
CATVIN
VHF/UHF
      
  Connect With Two Cable Boxes
VCR
IN FROM ANT.
OUT TO TV  AUDIO
IN 1
VHF/UHF
 R
 L
 VIDEO
OUT
CABLE BOX
OUT IN
IN
R
LOUT
TV
VIDEO AUDIO
VHF/UHF
      
  With a Cable Box (VCR 
      
   Cable Box)
ANT
or
CATV
You CannotYou Can
record
scrambled
channels.
TV VCRIN FROM ANT.
OUT TO TVVHF/UHF
VIDEO IN
R
AUDIO OUT
R
L
AUDIO INLR
VIDEO OUT
Set the VIDEO/TV selector of your TV (Monitor/Receiver) to “VIDEO.” Connect the “L” and “R” AUDIO OUT terminals on the VCR to the “L” and “R”
AUDIO IN terminals of your TV. Connect the VIDEO OUT terminal on the VCR to the VIDEO IN terminal
of your TV.
1
2
3
V4622 P22-44 (2nd) [LSQT0509B].p65 2002/05/23, 18:2924 
						

							25
MONO broadcastNormal monaural sound broadcast.
SAP broadcastSecondary Audio Program (sub language)
broadcast. Select SAP audio mode for the
sub language.
MTS Stereo broadcastMulti-channel Television Sound Stereo
broadcast. Select STEREO audio mode.
If stereo broadcast is weak and display
flickers, select MONO audio mode for
possibly better results.
MTS Stereo and SAP broadcastMulti-channel Television Sound Stereo (main
language) and Secondary Audio Program
(sub language) broadcasts are  being
received simultaneously. Select STEREO or
SAP audio mode.
The following are possible audio broadcast types and on-screen
displays. The signal being received is indicated with an “” mark
while the selected audio mode is indicated with an arrow.
Receivable Broadcast Types
Audio Mode for Recording
1
2
Do a recording.
See page 15.
3
Arrow indicates
selection.
STEREOSAPMONO
STOP       1 2 : 0 0AMABC  0 : 0 0 : 0 0 SPSTEREOSAPMONO
STOP       1 2 : 0 0AMABC  0 : 0 0 : 0 0 SPSTEREOSAPMONO
STOP       1 2 : 0 0AMABC  0 : 0 0 : 0 0 SPSTEREOSAPMONO
STOP       1 2 : 0 0AMABC  0 : 0 0 : 0 0 SPSTEREOSAPMONO
MTS Broadcast/ VHS Hi-Fi Stereo System
Audio Mode for Playback
Start playback.
See page 14.
Only tapes recorded in Hi-Fi stereo will playback with true stereo sound. Standard stereo
tapes will playback in monaural sound.
To listen to Hi-Fi stereo playback, the VCR AUDIO (L/R) jacks must be connected to a
stereo TV or an external stereo amplifier and speakers. (See top of this page.)
If tracking is adjusted during playback, Hi-Fi audio may revert to normal audio.
Hi-Fi and normal audio playback volume level may differ.
Arrow indicates
selection.Equipped with 
®-TV Noise
Reduction for true MTS
reproduction. 
®-TV Noise
Reduction is required for good
stereo separation and audio
fidelity. 
® is a registered
trademark, and is licensed by
® Technology Licensing.
Select “HIFI(L/R)” or
“HIFI(L)” or “HIFI(R)”
to listen to stereo
recordings in stereo
sound. Select
“NORMAL” for
monaural sound.
Stereo Amplifier
AUDIO INRL
VCR
RLR
OUT TO TV
VHF/UHF
TV
R
L
AUDIO OUT
DISPLAY
SAP/Hi-Fi
Connection
Make the Audio/Video Connection as shown on the
previous page.
 You can use a TV connected to a Stereo amplifier and
speakers instead of a Stereo TV.
To display the broadcast signal being received,➛ ➛➛ ➛
➛press DISPLAY.
Press SAP/ Hi-Fi
to display audio mode.
(Display disappears after 5 seconds.)Press SAP/ Hi-Fi
to display audio mode.
(Display disappears after 5 seconds.)
Press SAP/ Hi-Fi
repeatedly to
select desired
mode.
1
2
3
H I F I : L / RH I F I : L H I F I : RNORMAL
Notes
Advanced
Operation
Press SAP/ Hi-Fi
repeatedly to select
desired mode.
Refer to “Receivable
Broadcast Types” above.
V4622 P22-44 (2nd) [LSQT0509B].p65 2002/05/23, 18:2925 
						

							26For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
 Marking
When C/A RECORD: ON, VCR automatically rewinds the
tape after a recording has been made and marks the
beginning and end of any detected commercial blocks.
After marking is done, the tape is returned to the end of
the recording. Commercials are not erased from the tape.
Press ACTION*
to display menu.
Press  to select C/A and display
SET UP COMMERCIAL
ADV.
Press 
to select C/A RECORD
and press 
 to set.
ONTimer Recording, VCR Plus+ System, and One Touch recordings are marked automatically.
When STOP is pressed during normal recording, Select One of a)
or b) or c).
a) Press 1 key to mark the recording 
now.
“NOW MARKING COMMERCIALS” appears.
b) Press 2 key to mark the recording 
later (after the power has
been turned off).
If the tape is rewound and another recording started before the
power is turned off, commercials may not be marked correctly.
c ) Press ACTION to 
cancel the marking of this recording.When using the timer to record two
adjacent shows on the same
channel, better accuracy can be
obtained by programming each
show separately.
NUMBER
keys
 :PLAY :STOP :FF :REW
SELECT/
SET
ACTION
 detects and marks the beginning and
end points of commercials on your tape for recordings over 15
minutes in length. When 
 marked tape
is played back, the VCR a automatically advances through the
commercial segments at high speed. You can also set this feature
to Manual so as to have more control over the advance process.
The effectiveness of this system can vary due to differences in
the way television stations  broadcast. See page 28 for answers
to the most commonly asked questions about this feature.
OFFThe VCR will not mark commercials.
When you are editing or dubbing a tape, or when you do not wish to use this feature,
OFF should be selected.
2
3 1
SELECT  :               
EXIT       : ACT I ON     
REPEAT  PLAY             :OFF
T I ME  STAMP               :ON
REMOTE WARNING     :ON
AUTO  SHUT
- OFF       :OFF
AUTO  VCR/TV             :ONIDIOMA/LANGUE : ENGLISHVCR’ S  OUTPUT CH    :3
VCR       C / A    CLOCK       CH
SELECT  :               
EXIT       : ACT I ON     
SET  UP  COMMERCIAL  ADV.
   C/A  RECORD            :ON
   C/A  PLAYBACK        :AUTO
VCR      C / A       CLOCK       CH
VCR      C / A       CLOCK       CH
SELECT :              SET : 
EXIT      : ACT I ON     
SET  UP  COMMERCIAL  ADV.
   C/A  RECORD            :ON
   C/A  PLAYBACK        :AUTO
4
THE  VCR  IS  WAITING  TO
MARK  COMMERCIALS  IN  THE
PROGRAM  YOU  RECORDED.
MARKING
NOW          : PRESS  1
LATER      
  : PRESS  2
CANCEL    : PRESS  ACTION
Press ACTION again
to return to normal screen.
Tape Operation
Note
Ready Checklist
All connections are made.
One time Setup completed.
VCR is plugged in.
TV is turned on and set to CH3, 4
or Video on TV.
V4622 P22-44 (2nd) [LSQT0509B].p65 2002/05/23, 18:2926 
						

							27
 Playback
When playing back a recording which has been
marked using the  feature, you
can either set VCR to automatically advance through
marked commercial blocks, or set it so that
commercials are only skipped on your command.
AUTO :VCR will automatically advance through
marked commercial blocks recorded on the
tape and then resume playback.
MANUAL :VCR will advance through commercials only
when CA/ZERO is pressed. Playback will
resume when the end mark of a commercial
block is found, or a new recording or blank
portion is detected, or after 8 minutes.
The selection mode in step 3 remains set unless there is a power outage in which case the
original factory setting will be restored.
If playback is started in the middle of a commercial, only a single commercial is shown, or an
individual commercial is longer than 1 minute, the commercial may not be skipped.
Press FF to quickly advance through the commercial.
Part of a recorded program may be skipped over if the program portion between commercials
is less than 1 minute or there are frequent dark and quiet scenes during the program. To view
the portion of tape being incorrectly skipped, press PLAY while the VCR is skipping, reverse
the tape to a point just prior to where the skipping began and press PLAY again. This time the
group will not be automatically skipped. Automatic skipping will be re-enabled when the end of
the marked group is detected.
Press ACTION
to display menu.
Press  
to select C/A and
display SET UP
COMMERCIAL ADV.2
3 1
SELECT  :               
EXIT       : ACT I ON     
REPEAT  PLAY             :OFF
T I ME  STAMP               :ON
REMOTE WARNING     :ON
AUTO  SHUT
- OFF       :OFF
AUTO  VCR/TV             :ONIDIOMA/LANGUE : ENGLISHVCR’ S  OUTPUT CH    :3
VCR       C / A    CLOCK       CH
4
Press ACTION again
to return to normal screen.
PLAY
SELECT/
SET
ACTION
CA/ZERO *Important:If a remote control button does not work when pressed, press
the VCR button on the remote and try the button again.
 :PLAY :STOP :FF :REW
Advanced
Operation
SELECT  :               
EXIT       : ACT I ON     
SET  UP  COMMERCIAL  ADV.
   C/A  RECORD            :ON
   C/A  PLAYBACK        :AUTO
VCR      C / A       CLOCK       CH
 and are
registered trademarks of SRT, Inc.
A Jerry lggulden invention licensed
in association with Arthur
D. Little Enterprises, Inc.
U.S.Pat. No. 5,333,091;
5,692,093; 5,696,866
other patents pending
Notes
VCR      C / A       CLOCK       CHSET  UP  COMMERCIAL  ADV.
   C/A  RECORD            :ON
   C/A  PLAYBACK        :AUTO
SELE
CT   :            SET : 
EXIT        : ACT I ON     
FF
Press 
to select C/A PLAYBACK
and press  to set
“AUTO” or “MANUAL”.
V4622 P22-44 (2nd) [LSQT0509B].p65 2002/05/23, 18:2927 
						

							28For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Tape Operation (continued)
The most commonly asked questions about  are answered below.
Question
How fast does the VCR advance
through commercials?
Are commercials advanced through only
when I playback a recording?
Are commercials still recorded on the
tape in case I choose to view them
sometime?
Does 
 work in
all recording speeds?
Does the VCR advance through
commercials each time I playback tapes
which were recorded using
?
After marking commercials, does the
VCR stop at the end of the tape, or
rewind to the beginning?
Can I play my 
recordings in non-
 VCRs?
Does the marking process interfere with
other programmed recordings?
What happens if I cancel the marking in
progress so I can use the VCR?
What if part of my program is advanced
through along with the commercials?
Answer
The VCR advances through a 3-minute commercial
block in about 8 to 12 seconds if the tape speed is
SLP. In SP, it takes about 25 to 35 seconds.
Yes. The commercials are not marked until after the
recording is finished.
Yes. By setting the C/A PLAYBACK to MANUAL (see
page 27), you can view or advance through
commercials as desired.
Yes. 
 works in SP, LP, and
SLP.
Yes. As long as C/A PLAYBACK is set to AUTO (see
page 27), the VCR should advance through
commercials each time the tape is played back.
The tape stops at the end of the recording so that
any additional timer recordings can be performed.
Yes. 
 marked recordings will
play in non-
 VCRs, but
commercials will not be advanced through.
No. If the interval between 2 or more timer programs
is not sufficient to mark the recording, marking will be
done after all recordings are complete and the power
goes off.
Marking will be resumed when the VCRs power is
turned off as long as the tape has not been ejected.
Please see the 3rd note on page 27.
Additional Notes:
Because of the various ways in which commercials are broadcast, the VCR may not be able
to recognize all commercials.
If a timer recording is scheduled for the middle of the night, please be aware that the VCR will
make some noise as it rewinds and fast forwards the tape while marking commercials.
 and  are registered trademarks of SRT, Inc.
A Jerry lggulden invention licensed in association with Arthur D. Little Enterprises, Inc.
U.S.Pat. No. 5,333,091;
5,692,093; 5,696,866
other patents pending
V4622 P22-44 (2nd) [LSQT0509B].p65 2002/05/23, 18:2928 
						

							29
 helps you locate certain
parts of prerecorded movies (rented or
purchased). The feature works in two ways.
 You can go to the beginning of the movie.
 You can skip from one preview to the next.
 works only on tapes
recorded in SP speed with the record tab
removed.
1
2Start preview searching.
When a preview is detected, VCR
will start playback.
To Search for Preview.
Start next preview searching. 1) In step 3 at left, select GO
TO PREVIEW.
2)Press FF.
Press SEARCH/ M/A SKIP.
To cancel, press STOP.
 :PLAY :STOP :FF
SEARCH/
M/A SKIPSELECT/
SET
STOP PLAY
You can override the operation of SEARCH FOR
PREVIEWS mode by pressing SEARCH/ M/A
SKIP during tape searching.
 works by searching
the tape past each preview and then reversing
back to the start of the detected preview.
While the tape is reversing back, if SEARCH/ M/
A SKIP is pressed, 
 will
begin searching for the next preview.
While searching for the next preview, if you see
the start of a preview which you wish to watch,
press SEARCH/ M/A SKIP and
 will immediately
reverse back to the start of that preview,
instead of searching further past the preview
start point. Once the VCR is playing a preview,
press SEARCH/ M/A SKIP to advance to the
next preview, long commercial or the start of
the movie (whichever is next).
If you want to playback, press PLAY.
*Important:If a remote control button does not work when pressed, press
the VCR button on the remote and try the button again.
Ready Checklist
All connections are made.
One time Setup completed.
VCR is plugged in.
TV is turned on and set to CH3, 4
or Video  on TV.
Advanced
Operation
Insert a tape
without record tab.
Press SEARCH/
M/A SKIP* to
display SEARCH.
Select “GO TO START MOVIE,” if you want
to advance directly to beginning of the
movie.
➛ ➛➛ ➛
➛continue with step 4.
Select “GO TO PREVIEW,” if you want to
view the first (next) preview.
➛ ➛➛ ➛
➛see “To Search for Preview” at right.
Press FF
to start searching.
To cancel,
press STOP.
Press PLAY
to start playback.
When the movie is found...
To cancel,
press STOP.
2
3 1
4                   SEARCH
 INDEX    PROG. END      MOVIE
ENTER   INDEX  NUMBER  :1
USING   1- 9 KEYS
FORWARD  SEARCH :FF
REVERSE  SEARCH :REW
NEXT     :SEARCH  M/A  SK I PEXIT     :STOP
                   SEARCH
 INDEX    PROG. END      MOVIE
GO  TO  START  MOVIE
GO  TO  PREVIEW
SEARCH  START : FF
SELECT               :
EXIT     :
 SEARCH  M/A  SK I P
                   SEARCH
 INDEX    PROG. END      MOVIE
SEARCHING  FOR  START  
OF  MOVIE
CANCEL   :
 STOP
                   SEARCH
 INDEX    PROG. END      MOVIE
THE  MOV I E  I S  READY
START  :
 PLAY
CANCEL   : STOP
Press SEARCH/ M/
A SKIP twice to
select MOVIE and
press 
 to select
GO TO START
MOVIE or GO TO
PREVIEW.
5
If you inserted a cassette with the record tab
or if you selected “INDEX SEARCH”  go to
page 30.
V4622 P22-44 (2nd) [LSQT0509B].p65 2002/05/23, 18:2929 
						

							30For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
 To Calculate Index Number
Example 1:
To go to rec. 2 from rec. 4, enter 3 and press REW.
Example 2:To go to rec. 6 from rec. 2, enter 4 and press FF.
NOTE: 
 indicates start points of each recording.
If Index Search is started very close to an
index mark, that index mark may not be
counted in the search.
6157234
17534 62
Tape Operation (continued)
Search System
For each recording, an invisible index mark is placed on the tape. A program index and
information are also included for timer recordings. These marks are used to access or
scan recordings.
Press SEARCH/ M/A SKIP twice to
display SEARCH in Stop or Play mode.
1
Press FF on the
remote to start
PROGRAM END
SEARCH.
2
Locates end point of recording for continuity.
Examples of Program End Search.
➛ ➛➛ ➛
➛search continues 7 sec. past end point,
➛ ➛➛ ➛
➛tape rewinds to 10 sec. before end point,
➛ ➛➛ ➛
➛tape plays to end point and stops. Upon locating end point,
If Program End Search is started very
close to an index mark, that mark may be
skipped over.
                   SEARCH
 INDEX    PROG. END      MOVIE
SEARCH  START  :FF
NEXT     :SEARCH  M/A  SK I PEXIT     :STOP
Fig. 1
Program 2 or BLANK Program 1 
the current tape position 
Press SEARCH button
FF
INDEX
End Point
Fig. 2
Program  2 Program 1 
the current tape position 
Press SEARCH button
INDEXINDEX BLANK BLANK
FFEnd Point
Fig. 3
If search exceeds
a few seconds in
BLANK area.
Program  2 Program 1 
the current tape position 
Press SEARCH button
BLANKINDEX
FFEnd Point
Program End Search
Note
Note
Index Search
Press SEARCH/
M/A SKIP* to
display SEARCH
in Stop or Play
mode, and then
press NUMBER
keys to select
recording number.
To calculate
number, see below.
Press FF or REW
on the remote to
start search.
Play begins at end
of search.
To search forward
or back 1 index,
press FF or REW
on the remote or
VCR while screen
left is displayed (10
sec.).
To cancel, press
PLAY or STOP.
1
2
                   SEARCH
 INDEX    PROG. END      MOVIE
ENTER   INDEX  NUMBER  :1
USING   1- 9 KEYS
FORWARD  SEARCH :FF
REVERSE  SEARCH :REW
NEXT     :SEARCH  M/A  SK I PEXIT     :STOP
           INDEX  SEARCH
FORWARD SEARCH  : FF
REVERSE SEARCH  : REW      
To cancel, press
PLAY or STOP.
V4622 P22-44 (2nd) [LSQT0509B].p65 2002/05/23, 18:2930