Panasonic Video Cassette Recorder Pv V4622 Operating Instructions

11
3
Settings are made automatically.
When setup is done, this screen appears.
9 /29 / 20 0 2  SUN    2 : 20PMDST : ONSETT I NG  :   CH   10
AUTO  CLOCK  SET
     COMPLETED
VCR     C / A      CLOCK        CH
If “AUTO CLOCK SET IS INCOMPLETE”
appears, manually set clock.
See right.
AUTO  CLOCK  SET  IS
INCOMPLETE
PLEASE SET CLOCK BY
PRESSING ACTION KEY
VCR     C / A       CLOCK       CH
Confirm the output channel of your
cable box or DSS receiver. Press  to
select the same channel as the cable
box or DSS...

12For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Clock
1)Press   to select
CLOCK.
3)Press 
 and   to
select and set the
date, time, and DST
(Daylight Saving
Time).
4)Press ACTION to 
startthe clock and exit this
mode.
(“TIME ZONE ADJUST”
appears only when auto
clock is set.)
SEL.       :              REGLER:    QUITTER  : ACT I ON     
MAGNETO.   C / A    HORL.    CAREPRISE LECTURE       : NONHORODATEUR                 : OUIMESSAGE D’ ERREUR      :...

13
Time Zone Adjust
2)Press  to select
“TIME ZONE ADJUST.”
VCR’s Output
Channel
1)Press  to select
VCR’S OUTPUT CH.
REPEAT  PLAY             :OFFT I ME  STAMP               :ON
REMOTE WARNING     :ON
AUTO  SHUT
- OFF       :OFFAUTO  VCR/TV             :ONIDIOMA/LANGUE : ENGLISHVCR’ S  OUTPUT CH    :3
SELECT   :            SET : 
EXIT        : ACT I ON     
VCR       C / A    CLOCK       CH
2) Press .
3)Press ACTION.
After 3 seconds
REPEAT  PLAY             :OFFT I ME  STAMP               :ON
REMOTE...

14For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Playback a Tape
Rapid Rewind/ Fast Forward
(E.g., T-120 tape rewinds in approx. 1 minute.)
Press REW or FF in Stop mode.
Remove loose or
peeling labels from tapes
to prevent tape jam.
Insert a tape,VCR power comes on. “VCR” lights on Multi
Function Display. If Auto VCR/TV (p. 35) is
set to “OFF,” press VCR/TV until “VCR”
lights on the Multi Function Display.
Press PLAY to play tape.
If tape has no...

15
Multi Function
Display
After 5 min. in Pause mode, VCR
stops to protect the tape and the
video head. Insert a tape with a record tab (p. 4).
1
5 4 2
3VCR power comes on.
“VCR” lights on Multi Function
Display. If Auto VCR/TV (p. 35) is set to
“OFF,” press VCR/TV until “VCR”
lights on the Multi Function Display.
Press CH 
* or NUMBER keys
to select the channel.
For “LINE” input, see p. 36.
For channel over 100, first press 100
key then the other 2 digits.
Press SPEED
to select the record speed (p....

16For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Timer Recording
Press PROG/VCR+* button
to display PROGRAM.
Press PROG/VCR+
button to end the program. 2) To set remaining
items, press 
 to
select and press  to
set START/ STOP
times, CH (channel)
or LINE input (p. 36),
Category** and tape
speed (SP, LP, SLP).
3 2 1
4
1) Set record DATE,
press 
 to select:
1~31= one time, or
DAILY= MON~ FRI, or
WEEKLY= same time
each week and press
 to set.
See...

17
Press POWER and then press
STOP within 10 seconds to
cancel the Timer Recording.
(The TIMER indicator goes out
on Multi Function Display.)
To Replace program...
To Clear program...
Review, Replace or Clear Program Contents:
(Recording is not in progress)
Press to select number.
Press ADD/DLT.
or
Important notes when using a DSS receiver
When recording programs via a DSS receiver, the DSS receiver
must be left on.
When recording programs via an antenna or cable, the DSS
receiver must be turned off....

18For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Timer Recording Using VCR Plus+   System
1
Auto VCR Plus+ System Channel Setup (Part 1)
Press ACTION*
to display menu.
Press 
 
to select CHANNEL.
Press 
to select VCR Plus+
CH SET UP and
press 
 to display.
Make sure to leave VCR
off (overnight). In order for VCR to read PlusCode numbers, some set
up is required. Guide channel numbers are assigned to
each local broadcast and cable station. Because...

19
Auto VCR Plus+ System Channel Setup (Part 2)
Press    to
select channel map for
your area and press
ADD/DLT to set.
Before you perform the following steps, you
should have:
completed “Auto VCR Plus+ System
Channel Setup (Part 1)” on page 18.
left VCR off overnight, and turned it back on
after 9:00 AM the next day.
If channel updating wassuccessful...If VCR could notdistinguish channel map...
Press ACTION
to exit this mode.Press ACTION
to display SELECT
VCR Plus+ CH.
Continue with step 2.ACTION...

20For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
For [VCR
➛ ➛➛ ➛
➛TV] or [VCR
➛ ➛➛ ➛
➛cable box
➛ ➛➛ ➛
➛TV] connection only.
To enter VCR Plus+
channels,
press 
 to move cursor to
right, press  to enter
number, press 
  to set,
and press 
 to scroll up/
down. Press ACTION*
to display menu.
Manual VCR Plus+ Channel Setup
5
To complete step 5 of setup,
do the following:
Prepare a TV/Cable station line-up and
channels they are received on. Also, the...