Panasonic Vdr D50 Operating Instructions Manual

							91LSQT1319
∫Playback indications
∫Confirmatory indications
Motion picture playback
Still picture playback
1Playback (l54)
;Pause (l54)
5, /
6, Fast forward/rewind (l55)
7/8Last/first scene paused
9/:Skip playback (l54)
D/ESlow-motion playback (l55)
;1/2;Frame-by-frame playback 
(l55)
0h00m00sMotion picture playback time
01
01Play mode (l56)
All scenes on the disc 
displayed
Scenes recorded on the 
selected date displayed
Scenes in the selected playlist 
displayed
, , Motion picture recording mode 
(l38)
No.10Scene number
Volume adjustment (l55)
RResume playback (l56)
Contents that have been 
protected on another device
Locked still pictures (l66)
100-0001Still picture folder/file number 
display
XPSPLP
When a printer compatible with 
PictBridge is connected (l75)
Accessing the SD card (When 
connected to a PC)
1DPOF already set 
(to more than 1) (l67)
Number of recording pixels for 
still pictures (l40)
640k480
640k360
The picture size is not displayed for still 
pictures recorded with other products that have 
different picture sizes from the sizes shown 
above.
–– (Time 
display)The built-in battery is low. 
(l33)
°The warning/alarm indication 
appears when LCD monitor is 
rotated towards the lens side. 
Return the direction of the LCD 
monitor to normal position and 
check the warning/alarm 
indication.
No disc is inserted.
Unusable disc
No SD card is inserted.
Unusable card
0.3M
0.2
VDR-D50P&PC-LSQT1319_eng.book  91 ページ  ２００７年１１月１４日　水曜日　午後５時２１分 
						

							92LSQT1319
Indications
2
Messages
CANNOT READ THIS DISC. PLEASE CHECK FOR SCRATCHES OR STAINS ON DISC.
The disc is scratched or dirty. Eject the disc and clean it. (l24) If there are scratches on the disc, 
use a new disc.
THIS DISC IS INCOMPATIBLE.
You inserted an incompatible disc (copy-protected discs, etc.).
PLEASE CHECK THE DISC.
You inserted a disc that cannot be read on this unit (a disc recorded in an incompatible data format 
etc.).
RECOMMENDED TO USE PANASONIC DISC
You inserted a disc that does not meet the DVD standard for quality and performance so you may 
not be able to record normally. Refer to the following support site for information about discs that 
have been confirmed as compatible by Panasonic.
http://panasonic.jp/support/global/cs/e_cam (This website is in English only.)
CANNOT RECORD. (THIS DISC IS FINALIZED)
A finalized DVD-RW (Video format) or DVD-R/DVD-R DL disc has been inserted. After finalizing, 
the discs become play only and cannot record. If you un-finalize a DVD-RW (Video format) disc, it 
can be used for recording. (l69)
FINALIZE THE DISC TO ENABLE PLAYBACK ON OTHER DEVICES.
If you insert a DVD-RW or a DVD-R/DVD-R DL disc recorded in this unit (that has not been 
finalized) into another device such as DVD recorder, PC, etc., the disc may become unusable. Be 
sure to finalize the disc on this unit before inserting it in other devices.
CHECK CARD.
This card is not compatible or it cannot be recognized by the unit.
THIS BATTERY CANNOT BE USED.
Use a battery that is compatible with this unit. (l18)
You are attempting to connect an AC adaptor not compatible with this unit. Use the supplied AC 
adaptor. (l21)
If using a Panasonic battery compatible with this unit (l18), remove the battery and then insert it 
again. If the message appears even after repeating this several times, this unit needs repair. Detach 
the power and contact consumer support (l113, 114). Do not attempt to repair it by yourself.
VDR-D50P&PC-LSQT1319_eng.book  92 ページ  ２００７年１１月１４日　水曜日　午後５時２１分 
						

							93LSQT1319
It is possible that the system cannot complete writing of a file normally when, for example, power is 
turned off for some reason during recording or editing.
If faulty management information is found when a disc is accessed, the following message may appear. 
Be sure to follow the messages. (Repairing may take time depending on the error.)
≥When you repair the disc, use a battery with sufficient battery power or the AC adaptor. Even if the 
power is turned off without repairing the disc, you can repair the disc when you turn the power on 
again.
≥Depending on the condition of the data, it may not be possible to completely repair the data.
≥Do not repair a disc that has been recorded on another device. This may cause the loss of data or the 
disc.
PUSH THE RESET SWITCH.
CHECK THE DISC AFTER PUSHING THE RESET SWITCH TO REPAIR THE DATA.
An irregularity in the unit has been detected. Press the RESET button to restart the unit. (l99)
EXIT THE MENU THEN CHANGE TO MANUAL MODE.
CANCEL MAGICPIX MODE.
You are attempting to use a function that cannot be used simultaneously.
CANNOT SET.
With DVD-RW (Video format) and DVD-R/DVD-R DL discs, if the number of dates displayed when 
 (BY DATE) is selected is 99, you cannot change the aspect ratio from 16:9 to 4:3 and vice 
versa.
DISCONNECT USB CABLE.
The unit cannot correctly establish the connection to the PC or printer. Disconnect and reconnect 
the USB cable and then select the desired USB function again.
CANNOT OPERATE WHILE CONNECTED TO COMPUTER.
The unit’s power cannot be turned off when the unit is connected to the PC.
About recovery
DISC DATA IS NOW BEING REPAIRED. DO NOT SHAKE THE UNIT.
VDR-D50P&PC-LSQT1319_eng.book  93 ページ  ２００７年１１月１４日　水曜日　午後５時２１分 
						

							94LSQT1319
Helpful hints
1
Functions that cannot be 
used simultaneously
Some functions in this unit are disabled or cannot be selected due to the unit’s specifications. 
The table below shows examples of functions restricted by various conditions.
FunctionsConditions which
disable the functions
Digital zoom≥In picture recording mode
Fade
MagicPix≥While recording to a disc (Cannot set or cancel)
≥In picture recording mode
Backlight compensation≥When the MagicPix function is used
≥When the iris/gain is set
Soft skin mode (Set and cancel)≥While recording to a disc
Help mode
Scene mode≥In auto mode
≥When the MagicPix function is used
Change of white balance≥When digital zoom is used
≥When the MagicPix function is used
Adjusting the shutter speed, iris/gain≥When the MagicPix function is used
≥When the scene mode is used
VDR-D50P&PC-LSQT1319_eng.book  94 ページ  ２００７年１１月１４日　水曜日　午後５時２１分 
						

							95LSQT1319
Helpful hints
2
Frequently asked questions
What kind of discs can be used?
DVD-RAM, DVD-RW, DVD-R and DVD-R DL discs can be used if they are 8 cm (3z) 
non-cartridge discs. (l22)
Can discs with a cartridge be used?
They can be used if the cartridge is removed.
Can double sided discs be used?
They can be used.
However you cannot record or play continuously from one side of the disc to the other. 
You will need to eject the disc and turn it over.
Can I record continuously from one side of the disc to the other on a double sided disc?
You cannot record continuously from one side of the disc to the other. The recording time 
indicated on the disc package is the total time for both sides. You will need to eject the 
disc and turn it over to record on both sides.
Is playback possible on a DVD player?
By finalizing a DVD-RW (VR format/Video format) or a DVD-R/DVD-R DL disc in this unit, 
it can be played back on a DVD player.
To playback a DVD-RAM, DVD-RW (VR format), or DVD-R DL disc, you will need a DVD 
recorder or a DVD player that supports DVD-RAM, DVD-RW (VR format) or DVD-R DL 
disc. Refer to the operating instructions of the DVD recorder or DVD player.
VDR-D50P&PC-LSQT1319_eng.book  95 ページ  ２００７年１１月１４日　水曜日　午後５時２１分 
						

							96LSQT1319
Helpful hints
3
Troubleshooting
ProblemCheck points
This unit cannot be 
turned on.
This unit does not stay 
on long enough.
Battery runs down 
quickly.≥Charge the battery using the AC adaptor. (l18)
≥The battery protection circuit may have operated. Attach 
the battery to the AC adaptor for 5 to 10 seconds. If the unit 
still cannot be used, the battery is faulty.
≥Make sure the LCD monitor is opened or the viewfinder 
extended.
≥The battery is affected by ambient temperature. In cold 
places, the battery using time becomes shorter.
≥The battery has a limited life. If the operating time is still too 
short even after the battery is fully charged, the battery has 
worn out and needs to be replaced.
This unit is turned off 
automatically.≥If you do not use the unit for approximately 5 minutes, the 
power is automatically turned off to conserve battery life. To 
resume recording, turn the power back on.
The power will not turn off automatically when the power 
save function (l31) is set to [OFF].
This unit cannot be 
operated though it is 
turned on.
This unit does not 
operate normally.≥The unit cannot be operated unless you open the LCD 
monitor or extend the viewfinder.
≥Press the RESET button. (l99) If normal conditions are 
not restored yet, remove the battery or AC adaptor, wait 
about 1 minute and then reconnect the battery or AC 
adaptor. Then about 1 minute later, turn on the power 
again. (Performing the above operation when the access 
lamp is on may destroy the data on the disc or SD card.)
A clicking sound is heard 
when the power is turned 
off.≥This is the sound of the lens moving and is not a 
malfunction.
The screen has changed 
suddenly. 
(Demo mode is on.)≥If you set [DEMO MODE] to [ON] without inserting a disc or 
an SD card in video recording mode or picture recording 
mode, the unit is automatically set to the demonstration 
mode for introducing its functions. Normally this should be 
set to [OFF]. (l32)
VDR-D50P&PC-LSQT1319_eng.book  96 ページ  ２００７年１１月１４日　水曜日　午後５時２１分 
						

							97LSQT1319
ProblemCheck points
The DISC EJECT lever 
does not work.≥The disc cover will not open unless the unit is powered. 
Connect a charged battery or AC adaptor.
≥The DISC EJECT lever does not work after the unit is 
connected to the PC. Use Windows Explorer to right-click 
the drive icon and select [Eject]. Or select [Eject] from the 
software’s menu.
The disc cannot be read.≥If there are fingerprints or dirt on the disc, wipe them off. 
(l24)
A function indication 
such as the remaining 
time indication or the 
elapsed time indication is 
not shown.≥If you set [SETUP] # [DISPLAY] # [OFF], all indications 
other than warnings and date are not displayed.
Recording does not start, 
although power is 
supplied to the unit and 
the disc or SD card is 
correctly inserted.≥Rotate the mode dial to select   or  .
≥If the DVD-RAM or the DVD-RW (VR format) disc is write-
protected, release the protection. (l70) If the DVD-RAM 
or DVD-RW (VR format) disc was protected on another 
device, use the same device to release the protection.
≥Data cannot be recorded to finalized DVD-RW (Video 
format) and DVD-R/DVD-R DL discs. If you un-finalize a 
DVD-RW (Video format) disc, it can be used for recording. 
(l69)
≥No recording is possible while the SD card’s write protect 
switch is set to LOCK. (l26)
≥If the disc or SD card has no more available memory, free 
up some memory by deleting unnecessary scenes (l59) 
or use a new disc or SD card.
≥If the cover of the disc compartment is open, this unit may 
not operate normally. Close the disc cover.
Recording starts but 
stops immediately.
The playback picture 
breaks up for a moment.≥The disc is scratched or dirty. Eject the disc and clean it. 
(l24) If there are scratches on the disc, use a new disc.
≥The unit is hot. Follow the messages on the display.
To use the unit again, turn the unit off and leave it for a 
while.
Recorded still pictures 
are not clear.≥If you try to record small or finely detailed objects with 
[PICT.QUALITY] set at [ ], the images may break up into 
a mosaic-like pattern. Record with [PICT.QUALITY] set at 
[ ] instead. (l40)
VDR-D50P&PC-LSQT1319_eng.book  97 ページ  ２００７年１１月１４日　水曜日　午後５時２１分 
						

							98LSQT1319
Auto focus function does 
not work.≥Press the AUTO button.
≥There are some recording subjects and surroundings for 
which the auto focus does not operate correctly. (l104) If 
so, use the manual focus mode to adjust the focus. (l50)
“CHECK THE LENS 
COVER.” is displayed.≥Open the lens cover before turning the unit on.
≥This message may appear if you try to record in extremely 
dark places.
Sound is not played back 
from the built-in speaker 
of this unit.≥During playback, move the volume lever to display the 
volume indication and adjust it. (l55)
Although this unit is 
correctly connected to a 
TV, playback images 
cannot be seen.
The playback images are 
squeezed horizontally.≥Please read the operating instructions of your TV and 
select the video input that this unit is connected to.
≥Change the setting to match the aspect ratio of the TV. 
(l72)
Scenes or files cannot be 
deleted or edited.≥Release the protection. (l70)
If the disc or the contents on the disc have been protected 
on another device, release the protection on the same 
device.
≥It may not be possible to delete scenes that have been 
divided. Combine the divided scenes, and then delete 
them. (l62)
≥It may not be possible to delete scenes that are displayed 
as [ ] on the thumbnail display. If the scenes are 
unnecessary, format the disc or SD card to erase the data. 
(l71) Please be aware that if a disc or SD card is 
formatted then all the data recorded on the disc or SD card 
will be erased.
≥If the SD card’s write protect switch is set to LOCK, then 
deletion and editing are disabled. (l26)
≥Locked files cannot be deleted. Release the lock setting. 
(l66)
The images on the SD 
card do not look normal.≥The data may be destroyed. It may have been destroyed by 
static or electromagnetic waves. Store important data on a 
PC or other products as well.
ProblemCheck points
VDR-D50P&PC-LSQT1319_eng.book  98 ページ  ２００７年１１月１４日　水曜日　午後５時２１分 
						

							99LSQT1319
Even if a disc or an SD 
card is formatted, it 
cannot be used.≥Either this unit or the disc or SD card may be damaged. 
Please contact consumer support. (l113, 114) Use an SD 
card from 8 MB to 8 GB with this unit.
If the SD card is inserted 
in another device, it is not 
recognized.≥Check that the device is compatible with the capacity or 
type of SD card (SD Memory Card/SDHC Memory Card) 
that you inserted. Refer to the operating instructions of the 
device for details.
The indication 
disappears.
The screen is frozen.
No operation can be 
performed.≥No operation can be performed on this unit when it is 
connected to a PC.
≥Turn off the power to this unit. If the power cannot be turned 
off, press the RESET button, or remove the battery or AC 
adaptor and then reattach it. Turn on the power again. If 
normal operation is still not restored, detach the power 
connected, and contact consumer support. (l113, 114)
“PUSH THE RESET 
SWITCH.” or “CHECK 
THE DISC AFTER 
PUSHING THE RESET 
SWITCH TO REPAIR THE 
DATA.” is displayed.≥After using the following method to restart the unit, eject the 
disc and clean it. (l24) If there are scratches on the disc, 
use a new disc.
≥The unit has automatically detected an error. Press the 
RESET button with the projecting part of the grip belt A. 
This will restart the unit.
≥If you do not press the RESET button, the power to this unit 
is turned off automatically about 1 minute later.
≥Even after you press the RESET button, the indication may 
still appear repeatedly. If so, this unit needs repair. Detach 
the power connected, and contact consumer support. 
(l113, 114) Do not attempt to repair the appliance by 
yourself.
ProblemCheck points
A
VDR-D50P&PC-LSQT1319_eng.book  99 ページ  ２００７年１１月１４日　水曜日　午後５時２１分 
						

							100LSQT1319
When connected by the 
USB cable, this unit is not 
detected by the PC.≥Close the menu screen before connecting the USB cable.
≥Select another USB terminal on the PC.
≥Check the operating environment. (l79)
≥Disconnect the USB cable, turn the unit off then on and 
then reconnect the USB cable.
When the USB cable is 
disconnected, an error 
message will appear on 
the PC.≥To disconnect the USB cable safely, double-click the   
( ) icon in the task tray and follow the instructions on the 
screen.
ProblemCheck points
VDR-D50P&PC-LSQT1319_eng.book  100 ページ  ２００７年１１月１４日　水曜日　午後５時２１分