Panasonic Vdr D310 Operating Instructions Manual

							21LSQT1145
Before using
1While pressing the stopper A, 
pull out the battery holder.
2Set the button-type battery with 
its (r) mark facing upward and 
then put the battery holder back 
in place.
∫Concerning the button-type battery
≥When the button-type battery runs down, 
replace it with a new battery (part number: 
CR2025). The battery should normally last 
about 1 year, however this depends on how 
frequently the unit is used.
≥Keep the button-type battery out of the reach of 
children.
∫Remote control usable range
The distance between the remote control and the 
unit’s remote control sensor A: Within approx. 
5m (16feet)
Angle: Approx. 10o up and 15o down, left, and 
right
≥The remote control is intended for indoor 
operation. Outdoors or under strong light, the 
unit may not operate properly even within the 
usable ranges.
CAUTION
Danger of explosion if battery is incorrectly 
replaced. Replace only with the same or 
equivalent type recommended by the 
manufacturer. Dispose of used batteries 
according to the manufacturer’s instructions.
Replace battery with Panasonic PART NO. 
CR2025 only. Use of another battery may 
present a risk of fire or explosion.
Caution: Battery may explode if mistreated.
Dispose of used battery promptly. Keep away 
from children. 
Do not recharge, disassemble or dispose of in 
fire.
A
AA
LSQT1145.book  21 ページ  ２００６年１２月２８日　木曜日　午前９時３４分 
						

							Before using
22LSQT1145
Discs and cards
Discs that can be used on this unit
Disc typeDVD-RAM
8 cm (3z)
Single sided/
double sidedDVD-RW
8 cm (3z)
Single sided/double sided
(DVD-RAM 
Ver. 2.1)[DVD-RW Ver. 1.1/2X-SPEED (2X/1X)]
Recording formatDVD Video 
Recording format
(VR format)DVD Video 
Recording format
(VR format)DVD-Video format
(Video format)
CharacteristicRewritable disc Rewritable disc One time recording 
disc*1
Display on the screen
Indication in these 
instructions(RAM) (-RW‹VR›) (-RW‹V›)
Functions
≥Deleting recorded scenes¥¥–
≥Editing on this unit¥¥–
≥Playback on other 
products*2¥*3¥*4¥*5
≥Recording after finalizing –¥¥*6
LSQT1145.book  22 ページ  ２００６年１２月２８日　木曜日　午前９時３４分 
						

							Before using
23LSQT1145
*1 By formatting the disc, it can be used repeatedly. (l82)
*2 DVD players and DVD recorders that support 8 cm (3z) discs.
*3 Playback is possible on compatible products.
*4 Must be finalized on this unit. (l81) Playback is possible on compatible products.
*5 Must be finalized on this unit. (l81) Playback of DVD-R DL is possible on compatible products.
*6 Un-finalize the disc. (l82)
Disc typeDVD-R
8cm (3z)
Single sided/double sidedDVD-R DL
8cm (3z)
Dual layer on single side
(DVD-R for General Ver. 2.0) (DVD-R for DL Ver. 3.0)
Recording formatDVD-Video format
(Video format)DVD-Video format
(Video format)
CharacteristicOne time recording disc One time recording disc
Display on the screen
Indication in these 
instructions(-R)
Functions
≥Deleting recorded scenes –
≥Editing on this unit –
≥Playback on other 
products*2¥*5
≥Recording after finalizing –
¥: available –: not available
LSQT1145.book  23 ページ  ２００６年１２月２８日　木曜日　午前９時３４分 
						

							Before using
24LSQT1145
≥For the purposes of these operating instructions, DVD-R and DVD-R DL are referred to as the 
“DVD-R”.
≥Still pictures cannot be recorded on a disc with this unit. (VDR-D310/VDR-D230)
≥You cannot record or play continuously from one side of the disc to the other when using a double 
sided disc. You will need to eject the disc and turn it over.
≥Discs inserted in a holder, cartridge, or caddy case cannot be used. Always remove bare discs from 
these containers prior to use.
≥It is recommended that you use Panasonic discs. Usually discs compatible with the DVD standard 
can be used for recording and playback with no problems. However, some commercially available 
discs do not meet the DVD standard for quality and performance. If you use one of these discs, you 
may not be able to record or playback normally. (The message “RECOMMENDED TO USE 
PANASONIC DISC” appears.) Refer to the following support site for information about discs that have 
been confirmed as compatible by Panasonic.
http://panasonic.co.jp/pavc/global/cs/e_cam (This website is in English only.)
≥Discs recorded on this unit may not be playable on other products.
≥Recording on DVD-R in DVD Video Recording format is not supported.
≥When using DVD-RW or DVD-R, do not perform the following as it may make the disc 
unusable.
jRecord on a disc with other products after recording on it with this unit.
jRecord on a disc with this unit after recording on it with other products.
jInsert an un-finalized disc in any other products.
∫About format types
≥If a disc is recorded in VR format, the data can be exported on a computer.
∫About DVD-R DL (Dual Layer) 
DVD-R DL (Dual Layer) discs have two layers of recording/playback surface on one side.
If the first layer (L0) becomes full during recording, the recording continues uninterrupted on the second 
layer (L1). However, the recorded picture is divided into 2 scenes at the point where the layers switch. 
The unit automatically switches layers during disc playback so you can play the whole of the disc 
continuously like a normal disc. However, the image or sound momentarily stop at the point where the 
layers switch.
∫Examples of discs that cannot be used on this unit
What is the DVD Video Recording format (VR 
format)?
This is a format for recording on DVD discs 
which allows you to record and erase repeatedly 
and create playlists. You can record on DVD-
RAM and DVD-RW in VR format with this unit.What is the DVD-Video format (Video 
format)?
By finalizing the disc, it can be played back on 
most DVD players. 
You can record on DVD-RW and DVD-R in 
Video format with this unit.
≥Discs other than those with diameter of 8 cm (3z)≥CD-RW
≥Double layer discs other than DVD-R DL≥CD-R
≥iRW≥CD-ROM
≥iR≥CD
≥DVD-ROM
≥DVD-Video
LSQT1145.book  24 ページ  ２００６年１２月２８日　木曜日　午前９時３４分 
						

							Before using
25LSQT1145
When using DVD-RW, select whether to record in DVD Video Recording format (VR format) or DVD-
Video format (Video format) and then format the disc. (l24, About format types)
1When a brand-new DVD-RW is inserted in this unit, 
the screen on the right appears. Select [YES], then 
press the joystick.
2Select format type, then press the joystick.
3When the confirmation message appears, select [YES], then press the 
joystick.
≥To change the format type, format the disc again. (l82)
If the disc is formatted, then all the data recorded on the disc will be erased.
When using brand-new DVD-RW
[VIDEO]:DVD-Video format
[VR]:DVD Video Recording format
LSQT1145.book  25 ページ  ２００６年１２月２８日　木曜日　午前９時３４分 
						

							Before using
26LSQT1145
≥For the purposes of these operating instructions, SD Memory Card and SDHC Memory Card are 
referred to as the “SD card”.
≥Motion pictures cannot be recorded on an SD card with this unit.
≥Please confirm the latest information on the following website. (This website is in English only.)
http://panasonic.co.jp/pavc/global/cs/e_cam
≥This unit supports SD Memory Cards formatted in FAT12 system and FAT16 system based on SD 
Memory Card Specifications and SDHC Memory Cards formatted in FAT32 system.
≥Use this unit to format SD cards. If an SD card is formatted on other products (such as a computer), 
the time spent for recording may become longer and you may not be able to use the SD card. (l83)
≥We recommend that you use a Panasonic brand SD card.
≥When the write-protect switch A on SD card is locked, no recording, deletion or 
editing will be possible on the card.
≥Keep the Memory Card out of reach of children to prevent swallowing.
≥A MultiMediaCard cannot be used on this unit.
Cards that you can use with this unit (VDR-D310/VDR-D230)
Card typeSD Memory CardSDHC Memory Card
Capacity8 MB, 16 MB, 32 MB, 64 MB, 128 MB, 256 MB, 
512 MB, 1 GB, 2 GB4GB
Indication in these 
instructions(SD)
This unit is compatible with both SD Memory cards and SDHC Memory cards. You can only use 
SDHC Memory cards on devices that are compatible with them. You cannot use SDHC Memory 
cards on devices that are only compatible with SD Memory cards. (When using an SDHC Memory 
card on another device, be sure to read the operating instructions for that device.)
A
LSQT1145.book  26 ページ  ２００６年１２月２８日　木曜日　午前９時３４分 
						

							Before using
27LSQT1145
∫How to hold a disc or card
Do not touch the recording/playback surface or the 
terminal surface.
∫When inserting/removing a disc
Do not allow the recording/playback side of the disc to get dirty and avoid fingerprints.
≥If there is a scratch or dirt (e.g. dust or fingerprints) on the recording/playback side of the disc, images 
cannot be recorded or played back normally and the following phenomena may occur:
jRecording or playback becomes impossible.
jPlayback image stops momentarily or sound is interrupted during playback.
jBlock noise appears on playback images.
jThe message “PLEASE CHECK FOR SCRATCHES OR STAINS ON DISC.” appears.
∫If there is dirt or condensation on the disc
Wipe with a damp cloth and then wipe dry.
∫Handling precautions
≥Be careful about scratches and dirt.
≥Do not attach labels or stickers to discs. 
(This may cause disc warping and un-balanced rotation, rendering it unusable.)
≥Write on the label side of the disc only with a soft, oil-based felt pen. Do not use ballpoint pens or 
other hard writing implements.
≥Do not use record cleaning sprays, benzine, thinner, static electricity prevention liquids or any other 
solvent.
≥Do not use scratch-proof protectors or covers.
≥Do not drop, stack, or impact discs. Do not place objects on them.
≥Do not use the following discs:
jDiscs with exposed adhesive from removed stickers or labels.
jDiscs that are badly warped or cracked.
jIrregularly shaped discs, such as heart shapes.
≥Do not expose the terminals of the card to water, garbage or dust.
≥Do not place in the following areas:
jIn direct sunlight.
jIn very dusty or humid areas.
jNear a heater.
jLocations susceptible to significant difference in temperature (condensation can occur).
jWhere static electricity or electromagnetic waves occur.
≥Put discs and cards back in their cases for protection when not using them.
Disc and card handling
LSQT1145.book  27 ページ  ２００６年１２月２８日　木曜日　午前９時３４分 
						

							28LSQT1145
Setup
Setup
Power supply
When this unit is purchased, the battery is not 
charged. Charge the battery before using this 
unit.
≥If the DC cable is connected to the AC 
adaptor, then the battery will not charge. 
Remove the DC cable from the AC adaptor.
1Connect the AC cable to the AC 
adaptor and the AC outlet.
2Put the battery on the battery 
mount by aligning the mark, and 
then securely plug it in.
≥The output plug of the AC cable is not 
completely connected to the AC adaptor jack. 
As shown in A, there is a gap.
∫Charging lamp
≥Battery charging time (l29)
≥We recommend using Panasonic batteries. 
(l15, 143)
≥If you use other batteries, we cannot guarantee 
the quality of this product.
Push the battery against the battery 
holder and slide it until it clicks.
While sliding the BATTERY lever, 
slide the battery to remove it.
≥Hold the battery with your hand so it does not 
fall.
≥Before removing the battery, be sure to set the 
OFF/ON switch to OFF and check that the 
status indicator is off.
Charging the battery
Lights up: Charging
Goes off: Charging completed
Flashing: The battery is over discharged 
(discharged excessively). In a while, 
the lamp will light up and normal 
charging will start.
When the battery temperature is 
excessively high or low, the 
CHARGE lamp flashes and the 
charging time will be longer than 
normal.
A
Inserting the battery
Removing the battery
CAUTION
Danger of explosion if battery is incorrectly 
replaced. Replace only with the same or 
equivalent type recommended by the 
manufacturer. Dispose of used batteries 
according to the manufacturer’s instructions.
LSQT1145.book  28 ページ  ２００６年１２月２８日　木曜日　午前９時３４分 
						

							Setup
29LSQT1145
The times shown in the tables below are for when the temperature is 25oC (77oF) and the humidity is 
60%. If the temperature is higher or lower than 25oC (77oF), the charging time will become longer.
∫Charging time
≥The charging time shown in the table are approximations.
≥“2 h 25 min” indicates 2 hours 25 minutes.
VDR-D310:
VDR-D230/VDR-D210:
Charging time and recordable time
Battery model numberVoltage/capacityCharging time
Supplied battery/
CGA-DU12 (optional)7.2 V/1150 mAh 2 h 25 min
CGA-DU21 (optional) 7.2 V/2040 mAh 3 h 55 min
Battery model numberVoltage/capacityCharging time
Supplied battery/
CGR-DU06 (optional)7.2 V/640 mAh 1 h 40 min
CGA-DU12 (optional) 7.2 V/1150 mAh 2 h 25 min
CGA-DU21 (optional) 7.2 V/2040 mAh 3 h 55 min
LSQT1145.book  29 ページ  ２００６年１２月２８日　木曜日　午前９時３４分 
						

							Setup
30LSQT1145
∫Recordable time (When using a DVD-RAM disc)
≥The times indicate the recordable time when the viewfinder is used. The times in parentheses 
indicate the recordable time when the LCD monitor is used.
≥The actual recordable time refers to the recordable time on a disc when repeatedly starting/stopping 
recording, turning the unit on/off, moving the zoom lever, etc.
≥“1 h 25 min” indicates 1 hour 25 minutes.
VDR-D310:
Battery model 
numberVoltage/
capacityRecording 
modeMaximum 
continuously 
recordable timeActual recordable 
time
Supplied battery/
CGA-DU12 (optional)7.2 V/
1150 mAhXP1h25min
(1 h 20 min)35 min
(35 min)
SP1h40min
(1 h 30 min)45 min
(40 min)
LP1h45min
(1 h 40 min)45 min
(45 min)
CGA-DU21 (optional)7.2 V/
2040 mAhXP2h50min
(2 h 40 min)1h15min
(1h10min)
SP3h10min
(3 h)1h25min
(1h20min)
LP3h20min
(3 h 5 min)1h30min
(1h20min)
LSQT1145.book  30 ページ  ２００６年１２月２８日　木曜日　午前９時３４分