Panasonic Vdr D310 Operating Instructions Manual

							Others
121LSQT1145
Messages
CANNOT READ THIS DISC. 
PLEASE CHECK FOR 
SCRATCHES OR STAINS 
ON DISC.The disc is scratched or dirty. Eject the disc and clean it. (l27) If 
there are scratches on the disc, use a new disc.
NO DATA.There are no images recorded on the disc or card.
THIS DISC IS 
INCOMPATIBLE.You inserted an incompatible disc (copy-protected discs, etc.).
PLEASE CHECK THE 
DISC.You inserted a disc that cannot be read on this unit (a disc recorded 
in an incompatible data format etc.).
RECOMMENDED TO USE 
PANASONIC DISCYou inserted a disc that does not meet the DVD standard for quality 
and performance so you may not be able to record normally. Refer 
to the following support site for information about discs that have 
been confirmed as compatible by Panasonic.
http://panasonic.co.jp/pavc/global/cs/e_cam
(This website is in English only.)
AGS MODE ON -REC 
PAUSEDThe AGS function is activated. (l45)
CANNOT RECORD.
(THIS DISC IS FINALIZED)A finalized DVD-RW (Video format) or DVD-R has been inserted. 
After finalizing, the discs become play-only and cannot record. If you 
un-finalize a DVD-RW (Video format), it can be used for recording. 
(l82)
CANNOT RECORD. DISC 
IS FULL.
The disc is full or the number of scenes has reached the maximum 
limit so no further data can be recorded. Delete unnecessary scenes 
(l71) or insert a new disc.
CANNOT RECORD. THE 
NUMBER OF SCENES HAS 
EXCEEDED THE MAXIMUM 
LIMIT.
CANNOT OPERATE.
TEMPERATURE IS HIGH. 
PLEASE TURN OFF AND 
WAIT A WHILE.The temperature of the unit is high so it cannot be operated. Turn off 
the power, wait until the unit cools and then turn on the power again.
FINALIZE THE DISC TO 
ENABLE PLAYBACK ON 
OTHER DEVICES.If you insert a DVD-RW or a DVD-R disc recorded in this unit (that 
has not been finalized) into another device such as DVD recorder, 
computer, etc., the disc may become unusable. Be sure to finalize 
the disc on this unit before inserting it in other devices.
CANNOT UN-FINALIZE 
THIS DISC.DVD-R cannot be un-finalized.
CHECK CARD.This card is not compatible or it cannot be recognized by the unit.
LSQT1145.book  121 ページ  ２００６年１２月２８日　木曜日　午前９時３４分 
						

							Others
122LSQT1145
It is possible that the system cannot complete writing of a file normally when, for example, power is 
turned off for some reason during recording or editing.
If faulty management information is found when a disc is accessed, the following message may appear. 
Be sure to follow the messages. (Repairing may take time depending on the error.)
≥When you repair the disc, use a battery with sufficient battery power or the AC adaptor. Even if the 
power is turned off without repairing the disc, you can repair the disc when you turn the power on 
again.
≥Depending on the condition of the data, it may not be possible to completely repair the data.
≥Do not repair a disc that has been recorded on another device. This may cause the loss of data or the 
disc.
CARD LOCKED.The write protection switch on the SD card is set to LOCK. (l26)
CARD FULL.The SD card is full so no further data can be recorded. Delete 
unnecessary files (l78) or insert a new SD card.
PUSH THE RESET 
SWITCH.
An irregularity in the unit has been detected. Press the RESET 
button to restart the unit. (l130)
CHECK THE DISC AFTER 
PUSHING THE RESET 
SWITCH TO REPAIR THE 
DATA.
CHANGE TO MANUAL 
MODE.
You are attempting to use a function that cannot be used 
simultaneously.
CANCEL MAGICPIX MODE.
TURN OFF THE VIDEO 
LIGHT.
CANNOT SET.With DVD-RW (Video format) and DVD-R, if the number of dates 
displayed becomes 99 when [PLAY MODE] is set to [BY DATE], you 
cannot change the aspect setting from 16:9 to 4:3 and vice versa.
PLEASE CONNECT AC 
ADAPTORFinalizations cannot be executed and the unit cannot be connected 
to the computer when using a battery. Use the AC adaptor.
DISCONNECT USB 
CABLE.The unit cannot correctly establish the connection to the computer 
or printer. Disconnect and reconnect the USB cable and then select 
the desired USB function again.
CANNOT OPERATE WHILE 
CONNECTED TO 
COMPUTER.The unit’s power cannot be turned off when the unit is connected to 
the computer.
About recovery
DISC ERROR HAS OCCURRED. NOW REPAIRING DATA ON THE DISC.
LSQT1145.book  122 ページ  ２００６年１２月２８日　木曜日　午前９時３４分 
						

							Others
123LSQT1145
Functions that cannot be used simultaneously
Some functions in this unit are disabled or cannot be selected due to the unit’s specifications. 
The table below shows examples of functions restricted by various conditions.
FunctionsConditions which
disable the functions
Digital zoom
≥In picture recording mode
Fade
MagicPix≥While recording to a disc (Cannot set or cancel)
≥In picture recording mode
≥When the video light is on (gain up mode)
Backlight compensation≥When the MagicPix function is used
≥When the video light is on (gain up mode)
≥When the iris/gain is set
Soft skin mode (Set and cancel)
≥While recording to a disc Tele macro (Set and cancel)
Help mode
Video light on (gain up mode)≥When the MagicPix function is used.
Zoom microphone
≥An external microphone is used
Wind noise reduction
Scene mode≥When setting the AUTO/MANUAL/FOCUS switch 
to AUTO
≥When the MagicPix function is used
≥When the video light is on
Change of white balance≥When digital zoom is used
≥When the MagicPix function is used
≥When the video light is on (gain up mode)
Adjusting the shutter speed, iris/gain≥When the MagicPix function is used
≥When the video light is on (gain up mode)
≥When the scene mode is used
LSQT1145.book  123 ページ  ２００６年１２月２８日　木曜日　午前９時３４分 
						

							Others
124LSQT1145
Frequently asked questions
What kind of discs can be used?
DVD-RAM, DVD-RW, DVD-R and DVD-R DL can be used if they are 8 cm (3z) 
non-cartridge discs. (l22)
Can discs with a cartridge be used?
They can be used if the cartridge is removed.
Can double sided discs be used?
They can be used. 
However you cannot record or play continuously from one side of the disc to the other. 
You will need to eject the disc and turn it over.
Can I record continuously from one side of the disc to the other on a double sided disc?
You cannot record continuously from one side of the disc to the other. The recording time 
indicated on the disc package is the total time for both sides. You will need to eject the 
disc and turn it over to record on both sides.
Can DVD-R be recorded to once only?
Recording can be started and stopped until the disc is full.
However the data recorded on the DVD-R cannot be erased.
Is playback possible on a DVD player?
By finalizing a DVD-RW (VR format/Video format) or a DVD-R in this unit, it can be 
played back on a DVD player.
To playback a DVD-RAM, DVD-RW (VR format) or DVD-R DL, you will need a DVD 
recorder or a DVD player that supports DVD-RAM, DVD-RW (VR format) or DVD-R DL. 
Refer to the operating instructions of the DVD recorder or DVD player.
Can software other than that supplied be used?
For information about software from other companies, contact the makers of the 
software.
LSQT1145.book  124 ページ  ２００６年１２月２８日　木曜日　午前９時３４分 
						

							Others
125LSQT1145
Is playback possible on a computer? (Windows)
DVD-RAM, DVD-RW (VR format):
Use the supplied software DVD-MovieAlbumSE.
≥Before using DVD-RW (VR format) on a computer, be sure to finalize it on this unit.
DVD-RW (Video format), DVD-R:
Finalize the disc on this unit and then play it back with commercially available DVD-
Video playback software.
SD card:
Use picture viewer software.
Is editing possible on a computer? (Windows)
DVD-RAM:
Use the supplied software DVD-MovieAlbumSE.
DVD-RW (VR format), DVD-RW (Video format), DVD-R:
Editing is not possible on a computer.
Is it possible to copy data to a computer? (Windows)
DVD-RAM, DVD-RW (VR format):
Use VR disc copy tool or the File Export function in DVD-MovieAlbumSE.
≥Before using DVD-RW (VR format) on a computer, be sure to finalize it on this unit.
DVD-RW (Video format), DVD-R:
Copy with Windows Explorer. Data that has been copied to a computer can be 
written to a new disc with DVDfunSTUDIO.
≥Before using DVD-RW (Video format) or DVD-R on a computer, finalize them on 
this unit.
SD card:
Copy with Windows Explorer.
What should I do when the disc contents cannot be displayed with 
DVD-MovieAlbumSE?
If there are multiple drives, a drive other than this unit may be selected. Click the 
[Preference] button at top right of DVD-MovieAlbumSE screen, click the [Device setting] 
tab to choose the drive where the disc is loaded in the [Drive Select] column, and then 
click [OK].
Is playback possible on a computer (Macintosh)?
Discs:
Use ImageMixer 3.
≥Playback of DVD-RW (Video format) or DVD-R is possible on a standard OS or 
commercially available DVD-Video playback software.
≥Before using DVD-RW (VR format), DVD-RW (Video format) or DVD-R on a 
computer, finalize them on this unit.
SD card:
Use picture viewer software.
LSQT1145.book  125 ページ  ２００６年１２月２８日　木曜日　午前９時３４分 
						

							Others
126LSQT1145
Is editing possible on a computer (Macintosh)?
Use ImageMixer 3.
≥Motion pictures that have been saved to the ImageMixer 3 library can be edited.
≥Before using DVD-RW (VR format), DVD-RW (Video format) or DVD-R on a computer, 
finalize them on this unit.
Is it possible to save data to a computer (Macintosh)?
Discs:
Use ImageMixer 3.
≥Before using DVD-RW (VR format), DVD-RW (Video format) or DVD-R on a 
computer, finalize them on this unit.
SD card:
Copy with the Finder.
The recording date and time are not displayed on ImageMixer 3.
The recording date and time of images recorded on a DVD-RW (Video format) or DVD-R 
cannot be displayed. The recording date and time of images imported to the library can 
be set using [Options] in the [Information] function.
DVD-RAM or DVD-RW (VR format) icon is not displayed on the desktop (Macintosh).
What version of Mac OS X are you using? If it is V10.3.x or earlier, the icon is not 
displayed even if the disc is recognized by the computer. Use Disk Utility or Apple 
System Profiler to verify if the disc is recognized by the computer.
LSQT1145.book  126 ページ  ２００６年１２月２８日　木曜日　午前９時３４分 
						

							Others
127LSQT1145
Troubleshooting
ProblemCheck points
This unit cannot be 
turned on.≥Is the battery fully charged?
#Charge the battery using the AC adaptor. (l28)
≥The battery protection circuit may have operated. Attach the 
battery to the AC adaptor for 5 to 10 seconds. If the unit still 
cannot be used, the battery is faulty.
≥Is the LCD monitor opened or the viewfinder extended?
This unit is turned off 
automatically.≥If you do not use the unit for approximately 5 minutes, the 
power is automatically turned off to conserve the battery 
charge. To resume recording, turn the power back on.
The power will not turn off automatically when the power save 
function (l117) is set to [OFF].
This unit does not stay 
on long enough.≥Is the battery low?
#If the remaining battery power indication is flashing or the 
message “LOW BATTERY.” is displayed, the battery has run 
down. Charge the battery. (l28)
A clicking sound is heard 
when the power is turned 
off.≥This is the sound of the lens moving and is not a malfunction.
Battery runs down 
quickly.≥Is the battery fully charged?
#Charge it with the AC adaptor. (l28)
≥Are you using the battery in an extremely cold place?
#The battery is affected by ambient temperature. In cold places, 
the operating time of the battery becomes shorter.
≥Has the battery worn out?
#The battery has a limited life. If the operating time is still too short 
even after the battery is fully charged, the battery has worn out 
and can no longer be used. 
This unit cannot be 
operated though it is 
turned on.
This unit does not 
operate normally.≥The unit cannot be operated unless you open the LCD monitor 
or extend the viewfinder.
≥Press the RESET button. (l130) If normal conditions are not 
restored yet, remove the battery or AC adaptor, wait about 1 
minute and then reconnect the battery or AC adaptor. Then 
about 1 minute later, turn on the power again. (Conducting the 
above operation when the access lamp is on may destroy the 
data on the disc or card.)
The screen has changed 
suddenly.≥Has the demonstration started?
#If you set [DEMO MODE] to [ON] without inserting a disc or a 
card in video recording mode or picture recording mode, the unit 
is automatically set to the demonstration mode for introducing its 
functions. Normally this should be set to [OFF]. Press the MENU 
button, then select [SETUP] # [DEMO MODE] # [OFF] and 
press the joystick.
LSQT1145.book  127 ページ  ２００６年１２月２８日　木曜日　午前９時３４分 
						

							Others
128LSQT1145
The remote control does 
not function.≥Has the button-type battery of the remote control run out? 
#Replace it with a new button-type battery. (l20) 
The DISC EJECT lever 
does not work.≥The disc cover will not open unless the unit is powered.
#Connect a charged battery or AC adaptor.
≥The DISC EJECT lever does not work when the unit is 
connected to the computer. (l131, 132)
The disc cannot be read.≥Are there fingerprints or dirt on the surface of the disc?
#If there are fingerprints or dirt on the disc, wipe them off. (l27)
A function indication 
such as the remaining 
time indication or the 
elapsed time indication is 
not shown.≥If you set [SETUP]>[DISPLAY]>[OFF], indications other than 
warnings and date indications disappear.
Recording does not start 
although power is 
supplied to this unit and 
the disc or card is 
correctly inserted.≥Is the DVD-RAM or the DVD-RW (VR format) write-protected?
#Release the protection. (l82) If the DVD-RAM or DVD-RW (VR 
format) was protected on another device, release the protection 
on the same device.
≥Has the DVD-RW (Video format) or DVD-R been finalized?
#After finalizing, the discs become play-only and cannot record. If 
you un-finalize a DVD-RW (Video format), it can be used for 
recording. (l82)
≥Has the SD card’s write protect switch been set to LOCK?
#No recording is possible while the write protect switch is set to 
LOCK. (l26)
≥Is the memory of the disc or card full?
#If the disc or card has no more available memory, free up some 
memory by deleting unnecessary scenes (l71, 78) or use a 
new disc or card.
≥Is the unit set to the video recording mode or picture recording 
mode?
#No recording is possible unless the mode dial is at   or  .
≥Is the disc cover open?
#If the cover is open, this unit may not operate normally. Close the 
disc cover.
Recording starts but 
stops immediately.
The playback picture 
breaks up for a moment.≥Is the disc scratched or dirty?
#Clean the disc. (l27) If there are scratches on the disc, use a 
new disc.
≥The unit is hot. Follow the messages on the display.
To use the unit again, turn the unit off and leave it for a while.
The unit arbitrarily stops 
recording.≥Is the AGS function activated? 
#Record in the normal horizontal position or set [AGS] to [OFF]. 
(l45) 
ProblemCheck points
LSQT1145.book  128 ページ  ２００６年１２月２８日　木曜日　午前９時３４分 
						

							Others
129LSQT1145
Recorded still pictures 
are not clear.≥Are you trying to record small or finely detailed objects with 
[PICT.QUALITY] set at [ ]?
#If you try to record small or finely detailed objects with 
[PICT.QUALITY] set at [ ], the images may break up into a 
mosaic-like pattern. Record with [PICT.QUALITY] set at [ ] 
instead. (l52)
Auto focus function does 
not work.≥Is manual focus mode selected?
#Set the AUTO/MANUAL/FOCUS switch to AUTO.
≥Are you trying to record a scene which is hard to bring into 
focus in auto focus mode?
#There are some recording subjects and surroundings for which 
the auto focus does not operate correctly. (l137) If so, use the 
manual focus mode to adjust the focus. (l61)
Sound is not played back 
from the built-in speaker 
of this unit.≥Is the volume too low?
#During playback, move the volume lever to display the volume 
indication and adjust it. (l67)
Although this unit is 
correctly connected to a 
TV, playback images 
cannot be seen.
The playback images are 
squeezed horizontally.≥Have you selected video input on the TV? 
#Please read the operating instructions of your TV and select the 
channel that matches the input used for the connection.
≥Is the [TV ASPECT] setting correct?
#Change the setting to match the aspect ratio of the TV.
Press the MENU button, then select [SETUP] # [TV ASPECT] 
# [16:9] or [4:3] and press the joystick.
Scenes cannot be deleted 
or edited.≥Is the DVD-RAM or the DVD-RW (VR format) write-protected?
#Release the protection. (l82)
If the disc or the contents on the disc have been protected on 
another device, release the protection on the same device.
≥It may not be possible to delete scenes that have been divided.
#Combine the divided scenes, and then delete them. (l72)
≥It may not be possible to delete scenes that are displayed as 
[ ] on the thumbnail display. If the scenes are unnecessary, 
format the disc or card to erase the data. (l82, 83) Please be 
aware that if a disc or card is formatted then all the data 
recorded on the disc or card will be erased.
≥Is the file on the SD card locked?
#Locked files cannot be deleted. Release the lock setting. (l79)
≥If the SD card’s write protect switch is set to LOCK, then 
deletion is disabled. (l26)
The images on the SD 
card do not look normal.≥The data may be destroyed. It may have been destroyed by 
static or electromagnetic waves. Store important data on a 
computer or other products as well.
Even if a disc or a card is 
formatted, it cannot be 
used.≥Either this unit or the disc or card may be damaged. Please 
consult a dealer. Use an SD card from 8 MB to 4 GB with this 
unit.
ProblemCheck points
LSQT1145.book  129 ページ  ２００６年１２月２８日　木曜日　午前９時３４分 
						

							Others
130LSQT1145
With a computer (Windows)
The indication 
disappears.
The screen is frozen.
No operation can be 
performed.≥Is this unit connected to a computer?
#No operation can be performed on this unit when it is connected 
to a computer.
≥Turn off the power to this unit. If the power cannot be turned 
off, press the RESET button, or remove the battery or AC 
adaptor and then reattach it. After that, turn on the power 
again. If normal operation is still not restored, detach the 
power connected, and consult the dealer who you purchased 
this unit from.
“PUSH THE RESET 
SWITCH.” or “CHECK 
THE DISC AFTER 
PUSHING THE RESET 
SWITCH TO REPAIR THE 
DATA.” is displayed.≥Is the disc scratched or dirty?
#After using the following method to restart the unit, eject the disc 
and clean it. (l27) If there are scratches on the disc, use a new 
disc.
≥The unit has automatically detected an error. Press the RESET 
button with the projecting part of the lens cap A. This will 
restart the unit.
≥If you do not press the RESET button, the power to this unit is 
turned off automatically about 1 minute later.
≥Even after you press the RESET button, the indication may still 
appear repeatedly. If so, this unit needs repair. Detach the 
power connected, and consult the dealer who you purchased 
this unit from. Do not attempt to repair the appliance by 
yourself.
If the SD card is inserted 
in another device, it is not 
recognized.≥Check that the device is compatible with the capacity or type of 
SD card (SD Memory Card/SDHC Memory Card) that you 
inserted.
#Refer to the operating instructions of the device for details.
ProblemCheck points
Even if connected by the 
USB cable, this unit is not 
recognized by the 
computer.≥The USB function selection screen does not appear if the USB 
cable is connected while the menu screen is displayed.
#Close the menu screen before connecting the USB cable.
≥Is the AC adaptor connected?
#Use the AC adaptor when connecting the unit and a computer.
≥Select another USB terminal on the computer.
≥Check the operating environment. (l94)
≥Turn the unit off then on and disconnect then reconnect the 
USB cable.
ProblemCheck points
A
LSQT1145.book  130 ページ  ２００６年１２月２８日　木曜日　午前９時３４分