Panasonic Vdr D250 Operating Instructions Manual

							21LSQT1011
Before using
Parts identification and handling
∫Remote control usable range
The distance between the remote control and the unit’s remote 
control sensor A: Within approx. 5 m (16 feet)
Angle: Approx. 10o up and 15o down, left, and right
≥The remote control is intended for indoor operation. 
Outdoors or under strong light, the unit may not 
operate properly even within the usable ranges.
A
D250&300(P_PC)eng.book  21 ページ  ２００６年１月２０日　金曜日　午後２時３分 
						

							22LSQT1011
Before using
Parts identification and handling
This remote control can be used from different high and low angles. It is also handy when a tripod is 
used. When you do not use the remote control, attach the clip to the grip belt. Left-handed users 
can use this unit more easily.
1 Recording start/stop button [REC]
2 Zoom lever [W/T]
3 Photoshot button [PHOTO SHOT]
∫Connect the Magic Wire Remote Control to the unitPlug the Magic Wire Remote Control into the 
REMOTE/MIC terminal as far as it goes.
≥If the pin plug of the remote control is not inserted 
securely into the REMOTE/MIC terminal as far as it 
will go, normal operation may not be ensured.≥Before using, make sure that the plug is inserted 
securely into the terminal as far as it will go.
∫About the clip (on the backside)
When you move with the clip fitted to your pocket or elsewhere, beware of knocking 
over the tripod or causing the unit to fall off the table.
Using the Magic Wire Remote Control (optional)
1
2
3
D250&300(P_PC)eng.book  22 ページ  ２００６年１月２０日　金曜日　午後２時３分 
						

							23LSQT1011
Before using
Discs and cards
Discs and cards
Discs that can be used on this unit
DIsc typeDVD-RAM
8 cm (3z)
Single sided/
double sidedDVD-RW
8 cm (3z)
Single sided/double sidedDVD-R
8 cm (3z)
Single sided/
double sided
(DVD-RAM 
Ver. 2.1)[DVD-RW Ver. 1.1/
2X-SPEED (2X/1X)](DVD-R for 
General Ver. 2.0)
Recording formatDVD Video 
Recording 
format
(VR format)DVD Video 
Recording 
format
(VR format)DVD-Video 
format
(Video format)DVD-Video 
format
(Video format)
CharacteristicRewritable disc Rewritable 
discOne time 
recording disc*1
*1 By formatting the disc, it can be used repeatedly. (l98)
One time 
recording disc
Display on the screen
Indication in these 
instructions(RAM) (-RW‹VR›) (-RW‹V›) (-R)
Functions
≥Deleting recorded 
scenes¥¥––
≥Editing on this unit¥¥––
≥Playback on other 
products*2
*2 DVD players and DVD recorders that support 8 cm (3”) discs.
¥*3
*3 Playback is possible on compatible products.
¥*4
*4 Playback is possible on compatible products. (May have to be finalized on this unit.)
¥*5
*5 Must be finalized on this unit. (l100)
¥*5
≥Recording after 
finalizing–¥
¥*6
*6 Un-finalize the disc. (l101)
–
¥: available –: not available
D250&300(P_PC)eng.book  23 ページ  ２００６年１月２０日　金曜日　午後２時３分 
						

							24LSQT1011
Before using
Discs and cards
≥Still pictures cannot be recorded on a disc with this unit.
≥When using double sided disc, you cannot record or play continuously from one side of the disc 
to the other. You will need to eject the disc and turn it over.
≥Discs inserted in a holder, cartridge, or caddy case cannot be used. Always remove bare discs 
from these containers prior to use.
≥It is recommended that you use Panasonic discs. Usually discs compatible with the DVD 
standard can be used for recording and playback with no problems. However, some commercially 
available discs do not meet the DVD standard for quality and performance. If you use one of 
these discs, you may not be able to record or playback normally. (The message 
“RECOMMENDED TO USE PANASONIC DISC” appears.) Refer to the following support site for 
information about discs that have been confirmed as compatible by Panasonic.
http://panasonic.co.jp/pavc/global/cs/e_cam (This website is in English only.)
≥Discs recorded on this unit may not be playable on other products.
≥Recording on DVD-R in DVD Video Recording format is not supported.
≥When using DVD-RW or DVD-R, do not perform the following, as doing so may make the disc 
unusable.
– Record on a disc with other products after recording on it with this unit.
– Record on a disc with this unit after recording on it with other products.
– Insert an un-finalized disc in any other products.
∫About format types
∫Examples of discs that cannot be used on this unit
What is the DVD Video Recording format 
(VR format)?
This is a format for recording on DVD discs 
which allows you to record and erase 
repeatedly and create playlists. You can 
record on DVD-RAM and DVD-RW in DVD 
Video Recording format with this unit.What is the DVD-Video format (Video 
format)?
By finalizing the disc, it can be played back 
on most DVD players. 
You can record on DVD-RW and DVD-R in 
DVD-Video format with this unit.
≥DVD-RAM (2.6 GB) Ver. 1.0≥DVD-ROM≥MO
≥DVD-R (3.9 GB) Ver. 1.0≥DVD-Video≥MD
≥DVD-R (4.7 GB) for Authoring Ver. 2.0≥CD-R≥iD
≥iRW≥CD-RW≥Floppy disk
≥iR≥CD≥CD-ROM
≥DVD-R DL≥LD
≥Discs other than those with diameter of 8 cm (3z)
≥Dual/double layer discs
D250&300(P_PC)eng.book  24 ページ  ２００６年１月２０日　金曜日　午後２時３分 
						

							25LSQT1011
Before using
Discs and cards
When using DVD-RW, select whether to record in DVD Video Recording format (VR format) or 
DVD-Video format (Video format) and then format the disc. (l24, About format types)
1 When a brand-new DVD-RW is inserted in this 
unit, the screen on the right appears. Select 
[YES], then press the joystick.
2 Select format type, then press the joystick.
3 When the confirm screen appears, select [YES], then press the 
joystick.
≥To change the format type, format the disc again. 
(l98)
If the disc is formatted, then all the data recorded on 
the disc will be erased.
When using brand-new DVD-RW
VIDEO:DVD-Video format
VR:DVD Video Recording format
D250&300(P_PC)eng.book  25 ページ  ２００６年１月２０日　金曜日　午後２時３分 
						

							26LSQT1011
Before using
Discs and cards
≥Motion pictures cannot be recorded on an SD card with this unit.
≥Please confirm the latest information on the following website. (This website is in English only.)
http://panasonic.co.jp/pavc/global/cs/e_cam
≥For the purposes of these operating instructions, SD Memory Card and miniSD™ Card are 
referred to as the “SD card”.
≥This unit supports SD cards formatted in FAT12 system and FAT16 system based on SD Memory 
Card Specifications.
≥Use this unit to format SD cards. If an SD card is formatted on other products (such as a 
computer), the time spent for recording may become longer and you may not be able to use the 
SD card. (l99)
≥We recommend that you use a Panasonic brand SD card.
≥Be sure to insert miniSD™ Cards in the dedicated card adaptor before use. Inserting a card in 
this unit without the adaptor may damage the unit or the card. 
≥Do not insert an empty card adaptor in this unit. Do not leave the adaptor in this unit while 
inserting or removing miniSD™ Cards. This may cause the unit to malfunction.
≥When the write-protect switch on SD Memory Card is locked, no recording, deletion or editing will 
be possible on the card.
≥Keep the memory card out of reach of children to prevent swallowing.
≥MultiMediaCards cannot be used on this unit.
Cards that you can use with this unit
Card typeSD Memory CardminiSD™ Card
Capacity8 MB, 16 MB, 32 MB, 64 MB, 
128 MB, 256 MB, 512 MB, 
1 GB, 2 GB (Maximum)32 MB, 64 MB, 128 MB, 
256 MB, 512 MB
Indication in these 
instructions(SD)
Write-protect switch Locked status
D250&300(P_PC)eng.book  26 ページ  ２００６年１月２０日　金曜日　午後２時３分 
						

							27LSQT1011
Before using
Discs and cards
∫How to hold a disc or card
Do not touch the recorded surface or the terminal surface.
∫If there is dirt or condensation on the disc
Wipe with a damp cloth and then wipe dry.
∫Handling precautions
≥Be careful about scratches and dirt.
≥Do not attach labels or stickers to discs. (This may cause disc warping and un-balanced rotation, 
rendering it unusable.)
≥Write on the label side of the disc only with a soft, oil-based felt pen. Do not use ballpoint pens or 
other hard writing implements.
≥Do not use record cleaning sprays, benzine, thinner, static electricity prevention liquids or any 
other solvent.
≥Do not use scratch-proof protectors or covers.
≥Do not expose the terminals of the card to water, garbage or dust.
≥Do not drop, stack, or impact discs. Do not place objects on them.
≥Do not use the following discs:
– Discs with exposed adhesive from removed stickers or labels.
– Discs that are badly warped or cracked.
– Irregularly shaped discs, such as heart shapes.
≥Do not place in the following areas:
– In direct sunlight.
– In very dusty or humid areas.
– Near a heater.
– Locations susceptible to significant difference in temperature (condensation can occur).
– Where static electricity or electromagnetic waves occur.
≥To protect discs and cards, return them to their cases when you are not using them.
Disc and card handling
D250&300(P_PC)eng.book  27 ページ  ２００６年１月２０日　金曜日　午後２時３分 
						

							28LSQT1011
Setup
Power supply
Setup
Power supply
When this unit is purchased, the battery is not charged. Charge the battery before using this unit.
≥If the DC cable is connected to the AC adaptor, then the battery will not charge. Remove 
the DC cable from the AC adaptor.
1 Connect the AC cable to the AC adaptor and the 
AC outlet.
2 Put the battery on the battery mount by aligning 
the mark, and then securely plug it in.
≥The output plug of the AC cable is not completely connected to the 
AC adaptor jack. As shown in A, there is a gap.
∫Charging lamp
Lights up: Charging
Goes off: Charging completed
Flashing: The battery is over discharged (discharged excessively). In a while, the lamp will light up 
and normal charging will start.
When the battery temperature is excessively high or low, the CHARGE lamp flashes and 
the charging time will be longer than normal.
≥Battery charging time (l29)
≥We recommend using Panasonic batteries.≥If you use other batteries, we cannot guarantee the 
quality of this product.
Push the battery against the battery holder and 
slide it until it clicks.
While sliding the BATTERY RELEASE lever, slide 
the battery to remove it.
≥Hold the battery with your hand so it does not fall.
≥Before removing the battery, be sure to set the OFF/
ON switch to OFF and check that the status 
indicator is off before removing the battery.
Charging the battery
A
Fitting the battery
Removing the battery
D250&300(P_PC)eng.book  28 ページ  ２００６年１月２０日　金曜日　午後２時３分 
						

							29LSQT1011
Setup
Power supply
The times shown in the tables below are for when the temperature is 25oC (77oF) and the humidity 
is 60%. If the temperature is higher or lower than 25oC (77oF), the charging time will become 
longer.
∫Charging time
≥“2 h 25 min” indicates 2 hours 25 minutes.
≥The charging times shown in the table are approximations.
∫Recordable time
≥The times indicate the recordable time when the viewfinder is used. The times in parentheses 
indicate the recordable time when the LCD monitor is used.
(When using a DVD-RAM disc)
≥“1 h 25 min” indicates 1 hour 25 minutes.
≥The recordable times shown in the table are approximations.
≥Along with the reduction of the battery capacity, the 
display will change: 
####.
If the battery discharges, then   ( ) will 
flash.
≥The recordable time will become shorter in the 
following cases:
– When you use both the viewfinder and the LCD 
monitor simultaneously while rotating the LCD 
monitor frontward to record yourself, using the 
0 Lux MagicPix function, etc.
– When you use this unit with the LCD monitor lit up 
by pressing the POWER LCD button.≥The batteries heat up after use or charging. This 
unit will also heat up while being used. This is not a 
malfunction.
≥Be aware that the operating time of the battery will 
become shorter in low temperatures. We 
recommend charging a spare battery for use when 
recording.
Charging time and recordable time
Battery model numberVoltage/capacityCharging time
Supplied battery/
CGA-DU12 (optional)7.2 V/1150 mAh 2 h 25 min
CGA-DU21 (optional) 7.2 V/2040 mAh 3 h 55 min
Battery model 
numberVoltage/
capacityRecording 
modeMaximum continuously 
recordable time
VDR-D300VDR-D250
Supplied battery/
CGA-DU12 (optional)7.2 V/
1150 mAhXP1h25min
(1h20min)1h30min
(1 h 25 min)
SP1h35min
(1h30min)1h40min
(1 h 35 min)
LP1h40min
(1h35min)1h45min
(1 h 35 min)
CGA-DU21 (optional)7.2 V/
2040 mAhXP2h40min
(2h35min)2h50min
(2 h 40 min)
SP3h
(2h50min)3h10min
(2 h 55 min)
LP3h10min
(2h55min)3h15min
(3 h 5 min)
D250&300(P_PC)eng.book  29 ページ  ２００６年１月２０日　金曜日　午後２時３分 
						

							30LSQT1011
Setup
Power supply
1 Connect the AC cable to the AC adaptor and 
the AC outlet.
2 Connect the DC cable to the AC adaptor.
3 Connect the DC cable to this unit.
≥Do not use the AC cable for other equipment since the AC 
cable is exclusively designed for this unit. Do not use the 
AC cable from other equipment for this unit.
≥While the DC cable is connected to the AC adaptor, 
the battery will not charge.
≥(VDR-D250 only) When recording, remove the lens cap before turning the unit on.
If the unit is turned on with the lens cap attached, the automatic white balance adjustment 
(l163) may not function properly.
While pressing the button A, set the 
OFF/ON switch to ON.
The status indicator B lights and the power turns on.
≥(VDR-D300 only) In disc recording mode or card 
recording mode, the lens cover opens.
≥When the unit is turned on for the first time, a 
message asking you to set the date and time will 
appear. Select [YES] and set the date and time. 
(l45)
Connecting to the AC outlet
Turning the unit on/off
How to turn on the power
A
B
D250&300(P_PC)eng.book  30 ページ  ２００６年１月２０日　金曜日　午後２時３分