Panasonic Up/Down Wall Mount Kit, Up/Down Stand Kit UE-608030, UE-608031, UE-608032 Operating Instructions

							11
Operating Instructions
Usage
Moving the Stand
Stowing the Projector Assembly
Prepare to move the stand by carrying out the steps below.
1Disconnect the power cable from the power outlet.
2Move the projector.
•While lifting the projector arm slightly, turn it clockwise 
or counterclockwise slowly, and move the arm so that 
it is made parallel with the elite Panaboard unit.
Note
•At the lowest point, the projector may come into 
contact with the unit. Rotate the arm away, so 
that the projector will not touch the unit. 
3Attach knob B (with the board bracket 
attached) at the position shown in the figure 
and secure the projector arm.
Note
•The position of knob A varies depending on the 
projector used. 
4Lower the elite Panaboard to the lowest point.
Note
•If the height of the entrance is less than 2 m 
(6 ft. 63/4in.), proceed with steps 1 and 2, and after 
having moved the projector, lower the height of the 
projector arm by following the steps below.
1Attach knob B to the top hole. 
2Lift the projector arm slightly and remove knob A 
from the projector arm.
(The position of knob A varies depending on the 
projector used.)
3Lower the projector arm to the position where 
knob B stops it.
4Attach removed knob A to the securing position, 
and secure the projector arm.
Knob B
Knob A
Hole for Securing 
Projector Arm
 



Knob B Knob A
UE-608030_EN.book  11 ページ  ２０１０年１０月２８日　木曜日　午後４時２０分 
						

							12 Operating Instructions
Usage
Removing the Foot Reinforcing 
Assemblies
While grasping the release lever on the back side of 
each foot reinforcing assembly, pull the assembly from 
the stand base.
Notice
•Before moving the stand, be absolutely sure to 
remove the foot reinforcing assemblies from the stand 
base. If the stand is moved with these assemblies still 
attached, it may catch on surrounding objects, cause 
somebody to trip over and/or cause injury.
•In case of securing the foot reinforcing assemblies 
using the bolts, please contact your dealer.
Moving the Stand
First get somebody to help you. Then take hold of the 
frame on the elite Panaboard sides and protective 
cover of the stand, and move the stand together.Notice
When moving the stand
•Release the lock lever for each caster.
•Before moving the stand, disconnect the plug of the 
table tap from the wall outlet.
•Make sure that none of the cables are dragged along 
with the stand.
•Be absolutely sure to have another person ready to 
help you move the stand.
•Take care that none of the equipment placed on the 
table plate will fall off.
•While moving the stand, the stowed projector will 
move out of your field of view so while moving the 
stand, take care not to allow the projector to bump into 
a wall, door or other individuals around you.
After the stand has been moved, follow the steps below to 
return it to the condition in which it was before it was moved.
1Lock the stand’s casters.
2Turn the casters so that they point inwards.
3Re-attach the foot reinforcing assemblies.
4Return the knob currently in the hole for 
securing the projector arm to the hole on the 
board bracket. 
•If the height of the entrance is less than 2 m
(6 ft. 63/4in.), perform step 1 to 4 in the note 
(page 11) in reverse.
5Move the projector in front of the elite 
Panaboard.
6Connect the power cord. 
•Readjust the projector as needed and align it 
with the screen.
Foot Reinforcing Assembly Release Levers
UE-608030_EN.book  12 ページ  ２０１０年１０月２８日　木曜日　午後４時２０分 
						

							13
Operating Instructions
Appendix
Appendix
Troubleshooting
Symptom Possible cause and solution
Unusual sounds are heard while 
the elite Panaboard is moving 
up or down or the elite 
Panaboard feels extremely 
heavy when it is raised. Something may be wrong with the up/down unit. Stop using the elite 
Panaboard immediately, and contact your dealer.
Even when the elite Panaboard 
is raised, it drops down under its 
own weight. The adjustment part for raising and lowering the elite Panaboard may be 
out of position. 
Contact your dealer and ask for a service engineer to conduct the 
adjustments again.
UE-608030_EN.book  13 ページ  ２０１０年１０月２８日　木曜日　午後４時２０分 
						

							For Your Safety
14 Installation Manual
For Your Safety
Installation Manual (for qualified service personnel)
•Request assembly of the units and wall mounting from your dealer.
•Before constructing or installing the units, please read “Installation Manual (for qualified service personnel)” 
carefully. Panasonic System Networks Co., Ltd. cannot be held responsible for accidents or damage to 
property resulting from incorrect installation.
•Please read “For Your Safety” (pages 4–6 and pages 14–15) carefully and install the units safely.
•When installing the elite Panaboard on a wall or on the up/down unit, perform installation with 2 people.
For Your Safety
To prevent severe injury and loss of life, read this 
section carefully before using the unit to ensure proper 
and safe operation of your unit.
The following graphic symbols are used in this 
Installation Manual.
Notice
Denotes a 
potential hazard 
that could result in 
serious injury or 
death.
Denotes hazards 
that could result in 
minor injury or 
damage to the 
unit.
These symbols are used to alert 
operators to a specific operating 
procedure that must not be 
performed.
This symbol is used to alert 
operators to a specific operating 
procedure that must be 
emphasized in order to operate 
the unit safely.
This symbol is used to alert 
operators to a specific operating 
procedure that must be 
performed carefully.
WARNING
CAUTION
If the unit is hung on a wall, confirm the 
wall must be capable of supporting at 
least the following weight.
4,100 N (418 k gf)
Do not alter the unit and install. Installing 
an altered unit can cause injury.
Have the unit installed, removed and 
disposed of only by qualified service 
personnel.
Be sure to use the specified parts for the 
installation. Otherwise, it may cause 
injury.
Notes in the operating instructions or 
notes of labels on the unit should be 
observed.
Safety check must be done by qualified 
service personnel after installing this 
option.
WARNING
UE-608030_EN.book  14 ページ  ２０１０年１０月２８日　木曜日　午後４時２０分 
						

							For Your Safety15
Installation Manual
Safety
Do not attach the electronic board to 
mortared walls. Accidental electric 
leakage from the mounting bolts securing 
the up/down unit to metal laths or wire 
laths can cause heat, smoke or fire.
Confirm the bolts of the unit are certainly 
caught by the up/down unit by pulling the 
elite Panaboard after hanging the elite 
Panaboard on the up/down unit if the unit 
is mounted on a wall.
Be sure to put on a glove to avoid injury.
Do not remove the up/down locking 
plates until you are ready to attach the 
board and projector.
If these plates are removed by mistake, 
the up/down part may spring up and 
cause injury. 
Lock the casters (when using the stand) 
both after installation has been completed 
and after the stand has been moved.
If the stand is used with the casters 
unlocked, it may move or be overturned 
and/or cause injury.
After completing the installation or 
moving the stand to another location, be 
absolutely sure to attach the foot 
reinforcing assemblies to prevent the 
stand from toppling.
CAUTION
Locking the 
casters
(Push to lock)
Be careful around the projector ventilation 
area, which becomes hot.
Working in this area or touching nearby 
objects may cause injury. 
UE-608030_EN.book  15 ページ  ２０１０年１０月２８日　木曜日　午後４時２０分 
						

							Product Configuration
16 Installation Manual
Produc t Configuration
Packing Configuration
The following units are required when using the up/down stand kit or up/down wall mount kit.
Included Accessories
The following items are provided in the packing boxes. Check that they are present and accounted for.
∫Up/Down Unit (UE-608030)
Up/Down Stand Kit
Up/Down Unit UE-608030
Stand Table Unit UE-608031
Short-Throw Arm Unit UE-608032
Up/Down Wall Mount Kit Up/Down Unit UE-608030
Short-Throw Arm Unit UE-608032
No.Part NameIllustrationQ’tyNo.Part NameIllustrationQ’ty
1Cable Holder A15Board Mounting Screw 
(M6)4
2Cable Holder B
26Board Bracket 
Fastening Screw (M5)6
3Hook and Loop 
Fastener17Board Bracket
4
4Operating Instructions1
Unit × 1
UE-608030_EN.book  16 ページ  ２０１０年１０月２８日　木曜日　午後４時２０分 
						

							Product Configuration17
Installation Manual
∫ Stand Table Unit (UE-608031)
∫ Short-Throw Arm Unit (UE-608032)
No.Part NameIllustrationQ’tyNo.Part NameIllustrationQ’ty
8Bolt (M6 x 75 mm [215/16in.]) for 
Securing Left and Right Stands6=Collar for Securing 
Table Plate 4
9Collar for Securing Left 
and Right Stands6>Spring Washer for 
Securing Table Plate4
:Screw (M3 x 10 mm [13/32in.]) 
for Securing Protective Cover12?Flat Washer for 
Securing Table Plate 4
;Flat Washer for Securing 
Protective Cover12@Nut for Securing Table 
Plate 4

						

							Wall Mounting Construction
18 Installation Manual
Wall Mounting Construction
Checking the Wall
Which method should be used to mount the up/down wall mount kit depends greatly on the structure of the wall. The 
system to be mounted on the wall is heavy (up to 84 k
g [185.19 lbs] including the elite Panaboard and projector). Before 
proceeding with installation, therefore, consult with the  building manager, maintenance engineer or designer to verify 
that the wall has a structure strong enough to support the weight of the system. For safety, install the elite Panaboard 
only after thoroughly understanding the type of walls, the appropriate types of screws and the construction method.
I.Necessary Tools and Parts (not included with the up/down wall mount kit)
Tools Required for Assembly
Tools and Parts Required for Wall-Mounting Work
Other Parts
*Please choose local certified 4-Way Plug Adaptor.
Notice
•If necessary, have an extension cord ready. A total cable length (including extension cord) of approximately 
5m (16ft. 427/32in.) is required. 
II.Checkpoints to be Observed While Working
1Work-Related Safety Precautions
•Before mounting the up/down unit, read through the following points, and take care to avoid accidents.
— Be absolutely sure to wear a hardhat, protective shoes, safety belt and other safety gear.
— To ensure safety, be absolutely sure to do the work with another individual (= 2-person crew).
— Before proceeding with the work, check that there are no other individuals around you.
— To ensure that the work is accomplished safely and properly, make it a basic rule to strictly observe  all other applicable aspects of safety control.
— If there is a chance that the unit has ended up being deformed or damaged by unexpected impact  while it was being transported and installed, do not install it without taking appropriate measures. 
Otherwise, it may fall off the wall.
10 mm (
13/32in.) Wrench - - - 3
(Ideally, one of these should 
be a ratchet type of wrench.) 13 mm (1/2in.) 
Wrench - - - - - - - - - 1 4 mm (5/32in.) 
Allen Key  - - - - - - -  1 Phillips Head 
Screwdriver  - - - - - 1
Anchor- - - - - - - - - - - - - - - -4
M8 Bolt  - - - - - - - - - - - - - - -4
Flat Washer - - - - - - - - - - - -4
Spring Washer- - - - - - - - - - -4 The specified pull-out strength is required per anchor.
M8 anchor bolts are used when installing the up/down unit on the wall.
(Specified pull-out strength: 5,197.5 N [530 k
gf])
Drill Select the drill diameter specified for the anchors used.
Measuring Tape / Level
These are used to ensure that the holes drilled in the wall will be positioned precisely.
Dust Pump
This is used for cleaning purposes to ensure that no scraps or chips are left inside 
the holes. Note that the cleaning of the insides of the holes must be thorough 
because the drive bolts will be subject to a reactive force at the bottom of the holes.
Torque DriverUse a torque driver whose torque can be specified. 
(Recommended tightening torque: 
12.5 N•m [127 k gf•cm])
5m (16ft. 4
27/32in.) Video Cable (D-sub Cable) 5 m (16 ft. 427/32in.) Power Cable3 m (9 ft. 101/8in.) 
4-Way Plug Adaptor *
(with 3-Conductor 
Ground, Magnet)
UE-608030_EN.book  18 ページ  ２０１０年１０月２８日　木曜日　午後４時２０分 
						

							Wall Mounting Construction19
Installation Manual
2Concerning Installation
•The up/down stand kit and up/down wall mount kit are for indoor use. They cannot be used outdoors. 
Neither can they be installed or used in the following kinds of places.
— Places where they will be directly exposed to rain or water (including under the eaves of a house)
— Places where chemicals are used such as swimming pools
— Places with a lot of steam or grease such as manufacturing plants or kitchens, places with special 
environments such as those with combustible atmospheres
— Seaborne or coastal places and places where corrosive gases are given off
— Places subject to frequent vibrations such as in vehicles or ships (the up/down wall mount kit is not  designed to be used in or on vehicles)
— Places other than walls (this is applicable to the up/down wall mount kit)
— Places where the operating temperature range of the elite Panaboard will be exceeded
•To prevent deformation and discoloring, avoid installing the kits in places exposed to direct sunlight or 
near heating or cooling appliances, etc.
•When carrying out the work, be absolutely sure to abide by the construction-related laws and other 
related ordinances of the country concerned.
3Concerning the Installation Surface
•Mount the up/down unit in a stable location.  The specified pull-out strength is required per anchor.  
M8 anchor bolts are used when installing the up/down unit on the wall.
(Specified pull-out strength: 5,197.5 N [530 k gf])
•Avoid mounting the unit on a wall, which is not a principal st ructure component*, with a plasterboard, plywood or other 
such construction since these walls are weak. If mounting on such a wall is unavoidable, reinforce the wall adequately 
(by ensuring that its ultimate strength will be at least as great as the specified pull-out strength of the anchors).
*Principal Structural Component This term refers to walls, pillars, floors, beams, roofs and staircases, and it excludes partition walls, 
stud walls, attached columns, raised floors, floors on the bottom-most levels of buildings, floors of 
revolving stages, secondary beams, pent-roofs, partial sub-staircases, outdoor staircases and other 
structural parts of a similar nature which are not crucial to the building from a structural point of view.
4Concerning the Screws and Bolts Used
•When obtaining anchors and bolts locally, be absolutely sure that they satisfy the required specifications.
•Do not use wood screws.
5Concerning the Tightening of the Screws and Bolts
•Tighten the screws and bolts using the specified torque. Tightening them up using excessive torque will 
damage the screw threads, causing the unit to fall off the wall. Conversely, the screws will be loose if 
they are tightened up with insufficient torque.
•The torque levels are specified, so use a torque driver to tighten up the screws and bolts.
•The range in which the torque can be specified is limited for each torque driver. Refer to the 
recommended torque levels which are specified, and use the appropriate torque driver.
•Do not use an impact driver or power driver whose torque is difficult to control since using such a driver 
may damage the screws and bolts.
•Tighten the screws and bolts so they go straight in.
6Other Checkpoints
•Make sure that the location is large enough to accommodate the elite Panaboard.
Height: greater than 2,500 mm (8 ft. 27/16in.)
Width: greater than 2,100 mm (6 ft. 105/8in.)
•Make sure that the AC outlet is within 3 m (9 ft. 101/8in.) of where the system will be mounted and that 
it will not be behind the up/down unit and the elite Panaboard.
•Make sure that the Operating Instructions of the elite Panaboard to be mounted on the wall are at hand.
The Operating Instructions that are supplied with each elite Panaboard model describe how to install 
each elite Panaboard directly onto the wall and how to conduct the operation checks.
UE-608030_EN.book  19 ページ  ２０１０年１０月２８日　木曜日　午後４時２０分 
						

							Wall Mounting Construction
20 Installation Manual
Wall Types and Installation Procedures
I.When the Wall is a Principal Structural Component (a concrete wall which is at least 120 mm [43/4in.] thick)
Use the M8 bolts to mount the system on the wall. It is also necessary to provide anchors separately. The 
figure below shows the end mounting position of the up/down unit and the elite Panaboard vis-à-vis the hole 
positions. Check that there is enough space around the mounting position. Carefully read the instructions for 
the anchors which will be used, and check the correct hole diameters.
Note
•The above outline drawing for wall-mounting uses the UB-T880W as an example. The UB-T781 and other 
models have a smaller installation surface area than the UB-T880W so they can definitely be mounted if 
the space shown in the drawing is available.
Wall-Mounting Construction Procedure
1Drill the two top holes in the wall.
2Fasten the anchors to the holes.
3Insert the M8 bolts into the top left and right anchors and 
tighten them up until they only protrude approximately 4 mm
(
5/32in.) from the surface of the wall.
4With the help of another individual, take the up/down unit out of 
its packing box, and hang it on the wall by engaging the 
elongated holes at the top of the pipe on the rear surface of the 
unit with the two bolts.
5With the up/down unit hanging on the wall, mark off the 
positions of the holes used to secure the bottom part of the 
unit, put the up/down unit down, and drill the two bottom holes 
in the wall.
6Fasten the anchors to the bottom holes.
2500 mm 438 mm
530~785 mm
335~785 mm (when the pin end stopper is released)
900 mm
2100 mm 951 mm
A
100 mm
2,100 mm (6 ft. 1011/16in.)
951 mm (3 ft. 1
7/16in.)
2,500 mm 
(8 ft. 23/8in.)438 mm 
(1 ft. 51/4in.)
900 mm 
(2 ft. 11
7/16in.)
100 mm 
(315/16in.)
530 to 785 mm (1 ft. 87/8in. to 2 ft. 629/32in.)
335 to 785 mm (1 ft. 13/16in. to 2 ft. 629/32in.)
 (when the pin end stoppers are released)
UB-T880W / UB-T781W
•UB-T880: Above dimensions less 
122 mm (413/16in.)
•UB-T780 / UB-T781 / UB-T780BP:
Above dimensions less 25 mm (31/32in.)
ProjectorA
Panasonic 420 mm (1 ft. 417/32in.)
SANYO 567 mm (1 ft. 105/16in.)
EPSON 410 mm (1 ft. 45/32in.)
Optoma 389 mm (1 ft. 35/16in.)
Acer 385 mm (1 ft. 35/32in.)
BenQ 425 mm (1 ft. 423/32in.)
Bolt
Approx. 4 mm (
5/32in.)
Spring Washer
Flat Washer
(max. diameter of 16 mm [5/8in.])
UE-608030_EN.book  20 ページ  ２０１０年１０月２８日　木曜日　午後４時２０分