Panasonic Small Digital Business System 308/616 Installation Instructions

S-DBS Programming Instructions 
Vl .o Section 400 
Issue 1 July 1990 
Incidence of Harm to the Telephone Lines 
Should terminal equipment cause harm to the telephone network, the telephone company shall, where 
practical. notify the customer that temporary discontinuance of service may be required. However, 
where prior notice fs not practical. the telephone company may temporarily discontinue service 
forthwith. if such action is reasonable in the circumstances. In case of un-notified temporary...

Section 400 S-DBS Programming instructions 
Issue 1 July 1990 Vl .o 
Responsibility of Grantee (Manufacturer) of Registered Equipment 
The Grantee or its agent shall provide the user of the registered equipment with the following: 
(Al Instructions concerning instaUation. operation and repalr procedures. where apphcable. 
(B) Notification that the registered terminal equipment may not be used with party lines or coin lines. 
(C) Instruction indicating that when trouble is experienced the customer shall...

S-DBS Programming Instructions 
v1.0 Section 400 
Issue 1 JuIy 1990 
.-- - 
Table of Contents 
FCC RULES AND REGULATIONS (Part 68) ... 
.......................................... 
Ill 
Notifying the Telephone Company ... 
................................................ 
IJl 
RINGER EQUIVALENCE NUMBER (REN) 0.5 B ... 
..  .................................. 
Ill 
Connection to a Party Line or Coin Operated Telephone I.&e 
................ 
iii 
Incidence of Harm to the Telephone Lines 
.............. ..-...

SeWon 4UO 
Issue 1 July 1990 -- ._-----. sLDBsrg Ins~ctions 
v1.0 
HOW TO ENTER THE PROGRAM MODE .................................... 
Attendant’s phone .............................................................................. 
ON/OFF key of POWER SEEING ...................................................... 
HOW TO PROGRAM .................................................................. 
DATA TERMINAL PROGRAMMING ............................................ 
ENTERING THE DATA TERMINAL PROGRAMMING...

Section 400 
Issue .l ..JulEl990. 
-- S-DBS Programming Instnxt$ln; 
. 
PROGRAMMING GUIDELINES 
Before pro graag the small DBS system: 
a) Make certain all connections to the main unit have bee6 
properly installed and tested. See the Installation 
Instructions manual, Section 300. 
b) Complete the programming table form with all necessary 
information obtained from the end user. See page.2. 
cl Perform the initialization procedure before programming. 
See page 3. 
a  

S-DBS Programming Instructions 
VI.0 Section 400 
Issue 1 July 1990 
((..- -. 
1 i 
PROG-G DATA TABLE FORMS 
Enter features and installation specifications in a programming table form. 
See the Programming Table manual, Section 450. 
C :.) 
2  

Section 400 
Issue 1 July 1990 S-DBS Programming Instxuc~ln~ 
. 
- 
-___-- 
INITIALKXNG THE SYSTEM BEFORE PROGRAMMING 
Before programmin 
g for the first time, reset the system as follows: 
1. Turn off the power for the Main Cabinet. 
2. Set the RAlld switch to 9XZAR”. 
3. Turn the power for the Main Cabinet back on. 
4. Set the 
RAM switch to “HOLD”. 
a 
NOTE: This is a one-time operation. If the procedure 
is repeated at the next programming session, aJl 
previously programmed data will be erased. 
. 
3  

S-DBS Programming Instructions 
VI.0 Section 400 
Issue 1 July 1990 
SMALL DIGITAL BUSINESS SYSTEM PSD KEY SETTINGS 
The system consists of the following 6 modes. Each of these modes is represented 
by personal speed dial’ (PSD) keys l-6. See figure I on page 5 of this section. 
1. PSI) 1 Key - System Setting: 
Contains ail of the feature options which are system-wide 
based. 
2. PSD 2 Key - ‘Bunk Setting: 
Contains aII of the feature options on a per line basis. 
3. PSD 3 Key - Extension and Ring...

Section 400 
Issue 1 July 1990 
SMALXAH3S KEY TELEPEIONE 
S-DBS Programming Instructions 
v1.0 
‘. . 
PSD 6 PSD 7 
PSD 8 PSD 9 PSD 10 
0 m 0 0 0 
One-Touch 
PSD 1 PSD 2 PSD3 
PSD 4 PSD 5 =V= 
nnnnn 
FIGURE I  

S-DBS Programming Instructions 
v1.0 Section 400 
Issue 1 July 1990 
PROGRAMMING KEYS 
HOLD 
- Assigns data ~~advances-to-~~~~~er.- ..___ 
port at the same address. 
FLBH 
- Assigns data and returns to the previous 
port at the same address. 
# 
* 
AUTO - Assigns data and advances to the next higher 
address at the same port. 
- Assigns data and returns to the previous 
address at the same port. 
- Moves to a higher or lower address at the 
same port by pressing AUTO and entering the 
new address. 
CONF...