Panasonic Small Digital Business System 308/616 Installation Instructions

S-DBS Installation Instructions 
v1.0 Section 300 
Issue 1 August 1990 
ENVIRONMENT 
Electrical Noise 
-- 
_-. .--~-..--- -~--..- .---. 
ElectJical noise might disturb the operation of the system’s digital control circuits. 
Place the equipment away from heavy motors, welders or dimmers, and radio receivers 
and computers which generate electrical noise. 
Conversely, this system may interfere with radio receivers and computers. P&e the 
main unit at least 10 feet (3 meters) away fi-om ail other...

Section 300 
Issue 
1 August 1990 
ENVIRONMENT (continued) 
Vibration 
Do not install the system in an area with 
disconnection or loosening of components. 
Water Factor 
%s 
S-DBS Installation Instructions 
v1.0 
excessive vibration which can cause 
Water is a dangerous hazard to equipment and can totally damage the system. Do not 
place the equipment near anything containing water or under overhead plumbing, 
sprinkler system values or in areas that are susceptible-to flooding. 
B !e  

S-DBS Installation Instructions 
v1.0 Section 300 
Issue 1 August 1990 
INSTALLATION 
Always set the power switch to 6E’PTEEe instaE%~~EtionnectiEithe AC power to 
the key system unit (KSU). 
Use the appropriate screwdriver to fasten the screws. 22 
Handle the Main Unit carefully to avoid damaging the cover. 
.a 
1. Removing the Main 
Unit Cover 
a) Remove the two screws 
main unit. 0 a from &e front cover (B) of the 
b) Remove the tiont cover 
(B) by pulling it to the left@. 
Frant 
aover B 
0 b 
0 a...

Section 300 
Issue 1 August 1990 
* 
S-DBS Installation Instructions 
v1.0 
INSTALLATION (continued) 
2. Wall-Mounting. Procedure for the Main Cabinet Cover 
a) Attach four screws loosely to a wall stron 
fl enough 
to hold the wei ht of a KSU. The screws s ould 
___ _~_. 
- ---stand--out one- f ourth of an inch from-the wall surface. 
b) Pass the screws through the holes on the back of (r 
the main cabinet and pull the cabinet in a 
downward direction. - 
c) Tighten the two screws (A) and (B) with a...

*. 
Section 300 
Issue 1 August 1990 
f‘? 
I  S-DBS Installation Instructions 
v1.0 
INSTALLATl[ON (continued) 
3. Installing the Backup Battery 
a) Place the backup batteries (W-42130) in the 
battery compartment of the KSU. 
b) Insert the connecter cord of the batteries onto 
the BAT terminals of the KSU (+ and -). (? 
In case of power failure the backup battery will support normal system operation for, 
approximately, 30 minutes under full-load for the DBS3Q8 system and, approxi- 
mately, 20 minutes...

Section 300 
Issue 1 August 1990 
ei+ 
S-DBS Installation Instructions 
v1.0 
INSTALLATION (continued) 
4. Initializing the System 
a) Set the power switch of the main unit to OFF. 
b) Set the RAM switch in the center of the KSU 
Tom the HOLD to the CLEAR position. 
CJ plum the power surltcIi’?PtIie~iinitX~~ON~ 
d) Set the RAM switch back to-HOLD. Q 
Ram Switch 
Hold Clr MC0 
L  

S-DBS Installation Instructions 
v1.0 
KEY TELEPHONE 
1. Wall-Mounting Procedure 
4 
bl 
cl 
d) 
Place the telephone face down on a soft surface. 
Push in on the wide end of the dark grey wall 
adapter with thumbs or heels of hands until the 
adapter is released. 
Turn the adapter upside down. Insert the guides 
into the two adapter mounting holes at the 
lower end of the key telephone,-then push in 
the--adapter. --- .._ _- --.--.. 
a 
Place the mounting holes of the bracket over the 
studs of the...

Section 300 
Issue 1 August 1990 
Fci+ 
S-DBS Installation Instructions 
v1.0 
TRUNKLINES 
1. Connecting the Trunk Lines 
The telephone cable from the CO/PBX line can be directly connected to the outside 
line jack on the main unit. 
The DBS308 system has a six-pin modular jack (RI-25C) for COL 1, COL qand COL 
3. The DBS616 system has two modular jacks for COL 1, COL 2 and COL 3, and COL 
4, COL 5 and COL 6. 
y;z.ft the outside lines to the COL jack with a 6-w-ire modular cord no longer than 
I/  

___.---__ 
S-DBS Installation Instructions 
VI.0 
TRUNK LINES (continued) 
Figure 8 
Section 300 
Issue 1 August 1990 
P* 
/ ‘. . 
co 1-3 
CNl CN2 
CO 4-6 
rc > 
COL 1 
COL5 
111111 
< 
> < 
H COL3 COL6 MAIN 
UNlT 
.- 
c . 
I 
12  

Section 300 
Issue 1 August 1990 
%+ 
S-DBS Installation Instructions 
v1.0 
Use a female 25-pair cable to connect the extension ports to a 50-pin split block. 
The DBS308 system has one connector on the main unit for extensions 1 to 8, DPHl, 
DPH2 and PFU output. The DBS616 has two connectors for extensions 1 to 8 and 
extensions 9 to 16. 
Except for ports 1 and 2 which are for key telephones only, each extension port can 
connect a key telephone and/or a single line telephone (SLT). 
1. Connecting the...