Panasonic Sirius Satellite Radio Cr Srf100 Operating Instructions

CR-SRF100/CR-SRT10020 1.  “SIRIUS SATELLITE RADIO” will scroll across the display, twice.
2. If there is no antenna detected, “ANTENNA ERROR” will show on the second line of the display:
3. If the antenna is good, but no signal is found, “ACQUIRING SIGNAL” will show on the second line of 
the display:
4. Once satellite signal is present, the CDU will display the current channel number, category, and name
depending upon the current system configuration/setup.
NOTE: If your system is using an FM modulator...

CR-SRF100/CR-SRT10021
7.2.2. Shut-Down (Turn Off)
Press and hold the [SEL]button for greater than two seconds to turn the system off. The receiver mutes
the SSR audio, blanks the CDU display and turns off all indicators. If an FM Modulator is connected to the
system, it will switch back to the antenna to allow normal AM/FM radio operation .
17233_SGould  08/15/02  14:46  Page 21 

CR-SRF100/CR-SRT10022
7.3. Standard Operations & Screen Display Format
GENERAL KEYPAD HANDLING CHARACTERISTICS
In general, a function in the CDU is engaged by pressing and releasing the button. If any other button press
is detected while the first button is still depressed, the other button(s) function is ignored. The only excep-
tion from this is when a function requires simultaneous key presses (e.g., entering SETUP mode).
Therefore, in this manual, “press a key” actually means “press and release a...

CR-SRF100/CR-SRT10023 The channel name is displayed in the last 12 characters of the top line. If the full channel name is greater
than twelve characters in length, then the full channel name is scrolled across the display once, and the
eight-character abbreviated version is displayed thereafter.
The category name is displayed on the bottom line. If no category information accompanies this channel,
then this area of the display area will be blank.
If you change channels, there can be a slight delay in...

CR-SRF100/CR-SRT10024 Then pressing and releasing the [SEL]button will have the following effect:
followed shortly by:
17233_SGould  08/15/02  14:46  Page 24 

CR-SRF100/CR-SRT10025 And repeated pressing of the [SEL] button will have the following effect:
followed shortly by:
17233_SGould  08/15/02  14:46  Page 25 

CR-SRF100/CR-SRT10026 The display reverts to:
If the ARTIST or TITLE information is not available, the words “ARTIST” and “TITLE” are remain in their
place. If a PDT field other than ARTIST and TITLE does not contain information the field is skipped and the
next field that contains data is displayed.
DISPLAY WHEN TUNING TO A CHANNEL STORED IN A PRESET
No matter what mode you are in (PRESET, CHANNEL or CATEGORY), if you tune to a channel that is also
stored in a preset (rotating the [SEL]knob OR pressing...

CR-SRF100/CR-SRT10027
(STORING CHANNELS IN PRESETS
To store a channel in a preset, press and hold the preset button for 2 seconds. The receiver will emit a
short beep, indicating the channel is stored at that preset button in the current preset group.
RECALLING PRESET CHANNELS
If the user presses and releases a preset button [1] – [6]the system will select the channel stored at the
preset number for the current preset group.
17233_SGould  08/15/02  14:46  Page 27 

CR-SRF100/CR-SRT10028
7.4. Category Mode
The Sirius satellite system collects category information about each available channel. Any given channel
may be associated with zero, one, or more than one category. Therefore a category map is constructed with
each category identified with the specific channels associated with it.
This channel and category mapping can be illustrated as:
Through the use of preset buttons or by being in channel mode, it is possible to tune to a channel not in
the currently...

CR-SRF100/CR-SRT10029
EXITING FROM CATEGORY MODE
You exit category mode by entering a different mode. There are several ways to do this …
• press the [CHANNEL]button to enter CHANNEL mode.
• press the [PRESET]button to enter PRESET mode.
• enter SETUP mode.
The system indicates exiting category mode by turning off the category mode indicator located next to the
category button.
SELECTING A CATEGORY
You select a category by pressing the [CATEGORY] button until the desired category is displayed. If the...