Panasonic Sc Htb770 Owners Manual

Getting started
RQT977811
≥Use a screwdriver (i) for assembling the speakers.
≥Do not hold the speakers in one hand to avoid injury, you may drop the speakers when carrying them.
When carrying the active subwoofer
To avoid interference, maintain the following distances between the main unit/active subwoofer 
and other electronic devices that use the same radio frequency (2.4 GHz band).
	≥Place the active subwoofer within a few meters of the main unit and in a horizontal position with the top panel facing...

12RQT9778
Step 2  Assembling the speakers
The speakers can be wall mounted by drilling screws into the wall, etc. Make sure that the screw used and the wall are strong enough to support the weight of at least 33 kg (72.8 lbs).The screws and other items are not supplied as the type and size will vary with each installation.
≥For details about the required screws, refer to the diagram below the step “Drive a screw into the wall.” 
(>13).
≥For a safety measure to prevent the speakers from falling, refer to...

Getting started
RQT977813
Connect the speaker cables.
§ If you have difficulty inserting the cable, try straightening the speaker cable and then bending the 
cable about 20 mm (25/32q) from the tip, at an angle of approx. 45o (as illustrated above).
Drive a screw into the wall.
≥Use the measurements indicated below to identify the screwing positions on the wall.
≥Leave at least 20 mm (25/32q) of space above and on each side of the speaker to allow enough space for fitting the speaker.
≥Keep the screws...

14RQT9778
Wall mount the speakers:
Fit the speaker securely onto the screw(s).
Red connector:The speaker attached to the red connector cable is to be placed on the right side.
White connector: The speaker attached to the white connector cable is to be placed on the left side.
ARight speaker connector
BLeft speaker connector
DODO NOT
≥Move the speaker so 
that the screw is in this 
position.≥In this position, the 
speaker will likely fall if 
moved to the left or 
right.
Red
White...

Getting started
RQT977815
The speakers can be wall mounted by drilling screws into the wall, etc. Make sure that the screw used and the wall are strong enough to support the weight of at least 33 kg (72.8 lbs).The screws and other items are not supplied as the type and size will vary with each installation.
≥For details about the required screws, refer to the diagram below the step “Drive a screw into the wall.” 
(>17).
≥For a safety measure to prevent the speakers from falling, refer to page 24.
≥To...

16RQT9778
Assemble the center speaker:
Connect the speaker cable.
≥Insert the wire fully, taking care not to insert beyond the wire insulation.
Assemble the front speakers:
Attach the stand neck.
≥The two front speakers are interchangeable.
≥Keep the screws out of reach of children to prevent swallowing.
Assemble the front speakers:
Connect the speaker cables.
§ If you have difficulty inserting the cable, try straightening the speaker cable and then bending the 
cable about 20 mm (25/32q) from the tip,...

Getting started
RQT977817
Drive a screw into the wall.
≥Use the measurements indicated below to identify the screwing positions on the wall.
≥Leave at least 20 mm (25/32q) of space above and on each side of the speaker to allow enough space for fitting the speaker.
≥Keep the screws out of reach of children to prevent swallowing.
Front speakers
A
At least 30 mm
(13/16q)B‰4.0 mm (5/32q)
C‰7.0 mm to 
‰9.4 mm
(
9/32q to 3/8q)
DWall or pillar
E5.5 mm to 6.5 mm 
(
7/32q to 1/4q)
FFront speaker
(Rear view)
G100...

18RQT9778
Fit the speaker(s) securely onto the screw(s).
 
Red connector:The speaker attached to the red connector cable is to be placed on the right side.
White connector:The speaker attached to the white connector cable is to be placed on the left side.
ALeft speaker connectorBRight speaker connector
DODO NOT
Front speakerCenter speakerFront speakerCenter speaker
≥Move the speaker so that the screw is in this position.≥In this position, the speaker will likely fall if moved to 
the left or right.

...

Getting started
RQT977819
≥For a safety measure to prevent the speakers from falling, refer to page 24.
≥To prevent damage or scratches, lay down a soft cloth and perform the assembly on it.
Assemble the speakers following steps 1 and 2 of “Place the speakers 
horizontally” (>12, 13).
Attach the leg stands. 
≥Keep the screws out of reach of children to prevent swallowing.
When placing the speakers on a table
Place the speakers using the leg stands
∏2 Front 
speakers∏1 Center speaker∏3 Speaker cables...

20RQT9778
≥For a safety measure to prevent the speakers from falling, refer to page 24.
≥To prevent damage or scratches, lay down a soft cloth and perform the assembly on it.
Assemble the speakers following steps 1 and 2 of “Place the speakers 
horizontally” (>12, 13).
Attach the support legs and speaker feet.
≥Keep the screws and the speaker feet out of reach of children to prevent swallowing.
Place the speakers using the support legs and 
speaker feet
∏2 Front 
speakers∏1 Center speaker∏3 Speaker...