Panasonic Pv Dv203 Operating Instructions Manual

41
Digital Features
Digital Features
VCR mode
1Set POWER to VCR.
2Press MENU to display the VCR
FUNCTIONS menu screen.
3Rotate JOG KEY to select DIGITAL
 EFFECT , then press JOG KEY to
display the DIGITAL EFFECT menu
screen.
4Rotate JOG KEY to select D. ZOOM ,
then press JOG KEY to select ON.
Press MENU to exit.
5Press  (PLAY) to start playback.
The center portion of the image
doubles in size.
6Repeat steps 2~4 to select OFF to
cancel this feature.
5PLAY
Color recording of video or still images onto...

42For assistance,  please call :  1-800-211-PANA(7262) or send e-mail to : [email protected]
Digital Features
EIS ON NORMAL
1Set POWER to CAMERA.
2Press EIS to stabilize the picture.
Picture flicker may be observed when
taping under fluorescent lighting
conditions.
The EIS indicator flashes when the
light level is inadequate.
Turn D.E.I.S. OFF during recording
when using a tripod.
3Press REC/PAUSE to start recording.
4Press EIS again to cancel.
 Be sure that D.E.I.S. is turned off
when...

43
Digital Features
Digital Features
Other Digital Functions
Use the following features to add interest
and professionalism to your recordings or
playback. Select from twelve special
effects.
Note
Types of Digital Functions
MIRROR
Symmetrical image from the current camera
picture.
STROBE
The recording appears as a sequence of
still frames.
MOSAIC
The picture appears in a mosaic pattern.
SLIM
The picture is expanded vertically.
TRAIL
The subject being recorded creates a trail
when in motion.
STRETCH
The...

44For assistance,  please call :  1-800-211-PANA(7262) or send e-mail to : [email protected]
Digital Features
3, 4JOG KEY
1POWER
Picture in Picture (PinP)
You can display a PinP (still image) screen
on the Main Picture.
PinP position is fixed at the bottom right of
the screen.
Note
1Set POWER to CAMERA.
2Press MENU to display the CAMERA
FUNCTIONS menu screen.
3Rotate JOG KEY repeatedly to select
 DIGITAL EFFECT , then press JOG
KEY to display the DIGITAL EFFECT
menu screen.
4Press JOG KEY...

45
Editing Features
Editing Features
The original sound can be replaced with
new sound using the built-in Palmcorder
microphone.
Audio Dubbing using the
Built-in Microphone
1Set POWER to VCR.
If you have the optional Remote
Control, you can set the Palmcorder to
stop automatically at a specific point
on the tape. See “Memory-Stop
Editing” on page 46.
2Press  (PLAY). Then press
 (PAUSE) where you  want dubbing to
begin.
3Press MENU to display the VCR
FUNCTIONS menu screen.
Rotate JOG KEY to select...

46For assistance,  please call :  1-800-211-PANA(7262) or send e-mail to : [email protected]
Editing Features
4Press  (PAUSE) to start Audio
Dubbing. “A.DUB ” indication
appears.
Connect the Palmcorder to the TV in
order to monitor the sound.
(p. 39)
Only NTSC (National Television Standards
Committee) recorded tapes can be audio
dubbed. The following screen appears if
the tape was not recorded in NTSC format.
5Press  (PAUSE) to stop Audio
Dubbing. To listen to the desired audio sound, set...

47
Editing Features
Editing Features
S-Video In
VHF Connecting
Cable (not
supplied)TV
(To View)
A/V Cable
(Supplied)
To Audio InRecording:
VCR (Rear)
To S-Video In
(If there is S-Video In)
For technical reasons, dubbing a tape
may reduce its quality.
Press DISPLAY ON TV on the Palmcorder
Remote Control to eliminate EVF/LCD
Monitor indications.
If the Time Code is displayed in the EVF
or LCD monitor, it cannot be reset.
Only the DATE/TIME, when displayed, will
be recorded on the tape....

48For assistance,  please call :  1-800-211-PANA(7262) or send e-mail to : [email protected]
Editing Features
3, 4, 5PAUSE
3, 4PLAY
6STOP High quality digital-to-digital copying can be
accomplished if both Palmcorders incorpo-
rate the DV Input/Output (i.LINK) Connec-
tor (DV Interface cable (i.LINK) is not
supplied).
1Insert a pre-recorded tape into the
source (playing) Palmcorder, and set
POWER to VCR.
2Insert a blank tape with the record
tab closed into the target (recording)
Palmcorder...

49
Card Features
Card Features
You can record still images to a Memory Card.
1Set POWER to M-CARD.
The POWER lamp lights red.
Be sure POWER is fully turned to
M-CARD position.
“PLAY: PUSH PLAY KEY” is
displayed for 10 seconds. (p. 51)
2Press MENU to display CARD SETUP
menu, then press JOG KEY to select
 NORMAL or FINE .
Press MENU to exit this menu.
3Press PHOTOSHOT to record an
image.
The PhotoShot image is recorded to
the Memory Card.
When SHTR EFFECT is set to ON
(Menu OSD: p. 109), still...

50For assistance,  please call :  1-800-211-PANA(7262) or send e-mail to : [email protected]
1Repeat steps 1 and 2 on page 49.
2Set POWER to VCR.
3Press  (PLAY) to start playback of
the cassette tape. And then, press
 (PAUSE) to select an image.
4Press PHOTOSHOT to record the
desired image to the Memory Card.
When PHOTOSHOT is pressed in
PLAY or SLOW mode, the screen
goes to STILL mode.
To playback the images of the
Memory Card, see page 51.
When Variable Speed Search is
done (p. 35),...