Panasonic Projector PT-EW640 User Manual

							Chapter 3 Basic Operations — Operating with the remote control
ENGLISH - 51
Operating with the remote control
For PT-EZ580, PT -EW640  
and PT -EX610 For PT
-EW540 
and PT -EX510
Switching the input
The input for projection can be switched.
 button
1) Press the input selection (, , , , , ) 
buttons.
 fThis operation can be also performed using the  button on the control panel.
Switches the input to RGB1 or RGB2. Switches to another input when one input has already been chosen.
 *1 Switches the input to DIGITAL LINK.
Switches the input to DVI-D.
Switches the input to VIDEO.
*1Switches the input to DisplayPort.
Switches the input to HDMI.
*1 Only for PT-EZ580, PT-EW640 and PT-EX610
Note
 fWhen the optional Digital Interface Box (Model No.: ET -YFB100G) is connected to the  terminal, the ET -YFB100G input changes with each press of the  button. The input can also be changed using the control command of RS-232C.
For twisted-pair-cable transmitters of other manufacturers, switch the input on the projector to DIGIT AL LINK, and then switch the input on the twisted-pair-cable transmitter.
Using the SHUTTER/AV MUTE button
If the projector is not used for a certain period of time during the meeting intermission, for example, it is possible to turn of f the image and audio temporarily.
* button
(Only for PT-EZ580, PT-EW640 and PT -EX610)
 button
1) Press the  button.
 fThe image and audio disappear.
 fThis operation can be also performed using the  button on the control panel.  
						

							Chapter 3 Basic Operations — Operating with the remote control
52 - ENGLISH
2) Press the  button again.
 fThe image and audio reappear.
* button
(Only for PT-EW540 and PT -EX510)
 button
1) Press the  button.
 fThe image and audio disappear.
 fThis operation can be also performed using the  button on the control panel.
2) Press the  button again.
 fThe image and audio reappear.
Attention
 fWhen the [PROJECTOR SETUP] menu → [ECO MANAGEMENT] → [SHUTTER DETECTION] or [AV MUTE DETECTION] is set to [ON], do not switch on /off in a short time.
Note
 fThe power indicator  will flash slowly in green while the shutter function or AV mute function is in use.
Using the mute function
Audio can be temporarily turned off.
 button
1) Press the  button.
 fThe audio disappears.
2) Press the  button again.
 fThe audio reappears.
Adjusting the volume
The volume of the built-in speaker or audio output can be adjusted.
 button
1) Press the  button/ button on the remote control.
 fThis operation can be also performed using the  button/ button on the control panel.
Increases the volume.
Decreases the volume.
Using the freeze function
The projected image can be paused and audio turned off regardless of the playback of the external device.
 button
1) Press the  button.
 fThe image freezes and audio disappears.
2) Press the  button again.
 fFreezing of the image is canceled and audio reappears.  
						

							Chapter 3 Basic Operations — Operating with the remote control
ENGLISH - 53
Note
 f[FREEZE] is displayed on the screen when video is paused.
Using the on-screen display function
Turn off the on-screen display function (no display) when you do not wish the\
 viewers to see the on-screen display, such as the menu or the input terminal name.
 button
1) Press the  button.
 fThe on-screen display disappears.
2) Press the  button again.
 fThe on-screen display appears.
Note
 fIf you press the  button on the control panel for at least three seconds while the on-screen display is off (hidden), the on-screen display is turned on.
Using the presentation timer function
The presentation timer function can be operated.
Presentations, etc. can be performed while checking the elapsed time or \
time remaining in the preset time.
 button
1) Press the  button.
 fThe count is started.
 fThe elapsed time or the remaining time is displayed at the bottom right \
of the projected image.
2) Press the  button again.
 fThe count is stopped.
3) Press the  button again.
 fThe count is resumed.
Note
 fThe presentation timer is ended by holding the  button down for at least three seconds. fFor details such as presentation timer function settings, refer to [DISPLAY OPTION] menu → [P-TIMER] (x page 83).
Using the automatic setup function
The automatic setup function can be used to automatically adjust the resolution, clock phase, and image position when analog RGB signals consisting of bitmap images such as computer signals are being input, or to automatically adjust the image position when DVI-D/HDMI signals are input. Supplying images with bright white borders at the edges and high-contrast black and white characters is recommended when the system is in automatic adjustment mode. Avoid supplying images that include halftones or gradation, such as photographs and computer graphics.
 button
1) Press the  button.
 f[COMPLETE] is displayed when it has completed without any problem.
Note
 fThe clock phase may shift even if it has completed without any incident. In such cases, adjust the [POSITION] menu → [CLOCK PHASE] (x page 70). fIf an image with blurred edges or a dark image is input, [INCOMPLETE] may appear or adjustment may not be performed properly even when [COMPLETE] appears. In this case, adjust the settings in the [ADV ANCED MENU] menu → [INPUT RESOLUTION] (x page 73), [POSITION] → [CLOCK PHASE] (x page 70), and [SHIFT] (x page 68).
 fAdjust special signals according to the [DISPLAY OPTION] menu → [AUTO SETUP] (x page 76). fAutomatic adjustment may not work depending on the model of the computer . fAutomatic adjustment may not work for a synchronization signal of C-SY or SYNC ON GREEN.  
						

							Chapter 3 Basic Operations — Operating with the remote control
54 - ENGLISH
 fImages may be disrupted for a few seconds during automatic adjustment, but it is not a malfunction. fAdjustment is required for each input signal. fAutomatic adjustment can be canceled by pressing the  button during the automatic adjustment operation. fIf the automatic setup function is used while moving images are being input, the adjustment may not be performed properly even for an RGB signal that can use automatic setup. [INCOMPLETE] may appear, or adjustment may not be finished properly even if [COMPLETE] appears.
Using the keystone distortion correction function
The [KEYSTONE] menu can be displayed.
You can correct the keystone distortion that occurs when the projector is\
 installed tilted or when the screen is tilted.
 button
1) Press the  button.
 fThe individual adjustment screen of [KEYSTONE] or [CORNER CORRECTION] ([UPPER LEFT]) is displayed.
2) Press the  button again.
 fThe other individual adjustment screen is displayed.
When the [KEYSTONE] individual adjustment screen is displayed in Step 1), the [CORNER CORRECTION] individual adjustment screen ([UPPER LEFT]) is displayed.
Note
 fAfter the individual adjustment screen of [KEYSTONE] or [CORNER CORRECTION] is displayed, press asqw to adjust the keystone distortion.
 fEither setting of [KEYSTONE] or [CORNER CORRECTION] is enabled. If the other item is adjusted after [KEYSTONE] or [CORNER CORRECTION] was adjusted, the previous setting value will be reset. fIf the  button is pressed while the [CORNER CORRECTION] individual adjustment screen is displayed, the individual adjustment screen for the next corner is displayed. fRefer to the [POSITION] menu → [KEYSTONE] (x page 70) for details.
Using the digital zoom function
The [DIGITAL ZOOM] menu can be displayed.
You can enlarge images.
 button
1) Press the  button.
 fThe [DIGITAL ZOOM] screen is displayed.
2) Press qw to adjust the magnification.
3) Press the  button.
4) Press asqw to move the zoom position.
Note
 fRefer to the [DISPLAY OPTION] menu → [DIGITAL ZOOM] (x page 84) for details.
Switching the aspect ratio of the image
You can switch aspect ratios according to the input signal.
 button
1) Press the  button.
 fThe setting will change each time you press the button.
Note
 fRefer to the [POSITION] menu → [ASPECT] (x page 68) for details.  
						

							Chapter 3 Basic Operations — Operating with the remote control
ENGLISH - 55
Using the P IN P function
Locate a separate, small sub screen in the main screen to project two im\
ages simultaneously.
 button
1) Press the  button.
 fThe setting will change each time you press the button.
Note
 fRefer to the menu [P IN P] menu (x page 98) for details.
Using the function button
[SUB MEMORY], [SYSTEM SELECTOR], [DAYLIGHT VIEW], or [TEST PATTERN] operations can be assigned to the  button on the remote control so that it can be used as an easy shortcut button.
 button
1) Press the  button.
Note
 fAssignment of the function is performed from the [PROJECTOR SETUP] menu → [FUNCTION BUTTON] (x page 92).
Using the status function
You can display the status of the projector.
 button
1) Press the  button.
 fThe [STATUS] screen is displayed.
RGB2
SXGA60+-A1
65.22kHz/ 59.99Hz
1h
100h
200h
300h
27°C/ 80°F
27°C/ 80°F
1/4
MENU
ENTEREXIT
CHANGE SEND STATUS VIA E-MAIL
AROUND LAMP TEMP. INTAKE AIR TEMP.
: TOTAL: NORMAL
LAMP: ECO
PROJECTOR RUNTIME SIGNAL FREQUENCY SIGNAL NAME INPUT
STATUS
Note
 fThis can be displayed from the [PROJECTOR SETUP] menu → [STATUS] (x page 94).
Using the ECO management function
You can display the setting screen relating to ECO management.
 button
1) Press the  button on the remote control.
Note
 fRefer to the [PROJECTOR SETUP] menu → [ECO MANAGEMENT] (x page 87) for details.   
						

							56 - ENGLISH
Chapter 4 Settings
This chapter describes the settings and adjustments you can make using t\
he on-screen menu.   
						

							Chapter 4 Settings — Menu navigation
ENGLISH - 57
Menu navigation
The on-screen menu (Menu) is used to perform various settings and adjustments of the projector.
Navigating through the menu
Operating procedure
 button
1) Press the  button on the remote control or control panel.
 fThe [MAIN MENU] screen is displayed.
MAIN MENUPICTURE
POSITION
ADVANCED MENU
DISPLAY LANGUAGE
DISPLAY OPTION
PROJECTOR SETUP
P IN PTEST PATTERN
SIGNAL LIST
SECURITY
NETWORK
MENU SELECT
SUB MENUENTER
2) Press as to select an item from the main menu.
 fThe selected item is highlighted in yellow.
MAIN MENUPICTURE
POSITION
ADVANCED MENU
DISPLAY LANGUAGE
DISPLAY OPTION
PROJECTOR SETUP
P IN PTEST PATTERN
SIGNAL LIST
SECURITY
NETWORK
MENU SELECT
SUB MENUENTER
3) Press the  button.
 fThe sub-menu items of the selected main menu are displayed.
0
POSITION
SHIFT NORMAL
ASPECT
ZOOM
CLOCK PHASE
KEYSTONE
MENU SELECT
SUB MENU
ENTER   
						

							Chapter 4 Settings — Menu navigation
58 - ENGLISH
4) Press as to select a sub-menu, and press qw or the  button to change or adjust settings.
 fSome items will switch in order as follows each time you press qw.
ABC
 fFor some items, press qw to display an individual adjustment screen with a bar scale as shown be\
low.
0CONTRAST
ADJUST
Note
 fPressing the  button while the menu screen is displayed returns to the previous menu. fSome items may not be adjusted or used for certain signal formats to be input to the projector . The menu items that cannot be adjusted or used are shown in black characters, and they cannot be selected. [DIGITAL CINEMA REALITY] may not be displayed depending on the input signal. fSome items can be adjusted even if signals are not input. fIndividual adjustment screen is cleared automatically if no operation is performed for approximately five seconds. fFor menu items, refer to “Main menu” (x page 58) and “Sub-menu” (x page 59). fThe cursor color depends on the settings of the [DISPLAY OPTION] menu → [ON-SCREEN DISPLAY] → [OSD DESIGN]. The selected item is displayed with the yellow cursor by the factory default.
Resetting adjustment values to the factory defaults
If the  button on the remote control is pressed, the values adjusted in the menu items are restored to the factory default settings.
 button
1) Press the  button on the remote control.
0CONTRAST
ADJUST
Note
 fYou cannot reset all the settings to the factory default at a time. fTo reset all the settings adjusted in the sub-menu item to the factory default one at a time, execute [PROJECTOR SETUP] menu → [INITIALIZE] (x page 96). fSome items cannot be reset to the factory defaults by pressing the  button on the remote control. Adjust each item manually. fThe triangular mark under the bar scale in the individual adjustment screen indicates the factory default setting. The position of the triangular mark varies according to the selected input signals.
Current adjustment value
Factory default setting
Main menu
The following items are in the main menu.
When a main menu item is selected, the screen changes to a sub-menu sele\
ction screen.
Main menu itemPage
[PICTURE]62
[POSITION]68
[ADVANCED MENU]72
[DISPLAY LANGUAGE]74
[DISPLAY OPTION]75
[PROJECTOR SETUP]86
[P IN P]98   
						

							Chapter 4 Settings — Menu navigation
ENGLISH - 59
Main menu itemPage
[TEST PATTERN]100
[SIGNAL LIST]101
[SECURITY]104
[NETWORK]107
Sub-menu
The sub-menu of the selected main menu item is displayed, and you can se\
t and adjust items in the sub-menu.
[PICTURE] 
Sub-menu itemFactory defaultPage
[PICTURE MODE][STANDARD]62
[CONTRAST][0]62
[BRIGHTNESS][0]63
[COLOR][0]63
[TINT][0]63
[COLOR TEMPERATURE][DEFAULT]63
[GAMMA][0]65
[SHARPNESS][+6]*165
[NOISE REDUCTION][OFF]65
[IRIS]*2[OFF]*165
[DAYLIGHT VIEW][AUTO]66
[SYSTEM SELECTOR][YPBPR]*166
*1 Depends on the signal input.*2 Only for PT-EZ580, PT-EW640 and PT-EX610
Note
 fThe factory default settings may vary depending on the picture mode.
[POSITION] 
Sub-menu itemFactory defaultPage
[SHIFT]―68
[ASPECT][NORMAL]*168
[ZOOM]―69
[CLOCK PHASE][0]*170
[KEYSTONE]―70
*1 Depends on the signal input.
[ADVANCED MENU] 
Sub-menu itemFactory defaultPage
[DIGITAL CINEMA REALITY][AUTO]*172
[BLANKING]―72
[INPUT RESOLUTION]―73
[CLAMP POSITION][24]*173
[RASTER POSITION]―73
*1 Depends on the signal input.
Note
 fSub-menu items and factory default settings vary depending on the selected input terminal.   
						

							Chapter 4 Settings — Menu navigation
60 - ENGLISH
[DISPLAY LANGUAGE] 
Details (x page 74)
[DISPLAY OPTION] 
Sub-menu itemFactory defaultPage
[COLOR ADJUSTMENT][OFF]75
[COLOR CORRECTION][OFF]75
[SCREEN SETTING]―76
[AUTO SIGNAL][OFF]76
[AUTO SETUP]―76
[RGB IN]―77
[DVI-D IN]―78
[HDMI IN]―78
[DIGITAL LINK IN]*1―79
[DisplayPort IN]*1―79
[ON-SCREEN DISPLAY]―79
[CLOSED CAPTION SETTING]―81
[BACK COLOR][BLUE]82
[STARTUP LOGO][DEFAULT LOGO]82
[SHUTTER SETTING]*1―82
[P-TIMER]―83
[FREEZE]―84
[DIGITAL ZOOM][1.5]84
*1 Only for PT-EZ580, PT -EW640 and PT -EX610
[PROJECTOR SETUP] 
Sub-menu itemFactory defaultPage
[PROJECTOR ID][ALL]86
[PROJECTION METHOD][FRONT/FLOOR]86
[ECO MANAGEMENT]―87
[SCHEDULE][OFF]88
[STARTUP INPUT SELECT][LAST USED]90
[RS-232C]―90
[REMOTE2 MODE][DEFAULT]92
[FUNCTION BUTTON]―92
[AUDIO SETTING]―92
[STATUS]―94
[DATE AND TIME]―95
[SAVE ALL USER DATA]―96
[LOAD ALL USER DATA]―96
[INITIALIZE]―96
[SERVICE PASSWORD]―97
[P IN P] 
Details (x page 98)
[TEST PATTERN] 
Details (x page 100)