Panasonic Projector PT-EW640 User Manual

							Chapter 4 Settings — [NETWORK] menu
ENGLISH - 111
 fFor the LAN cable between a twisted-pair-cable transmitter and the projector, use a cable that meets the following criteria:
 gCompatible with CAT5e or higher
 gShielded type (including connectors)
 gStraight-through
 gSingle wire
 fThe maximum transmission distance between the twisted-pair-cable transmitter and the projector is 100 m (328'1"). If this distance is exceeded, image and sound may be disrupted and may cause a malfunction in LAN communication.
 fWhen laying cables between a twisted-pair-cable transmitter and the projector , check that cable characteristics are compatible with CAT5e or higher using tools such as a cable tester or cable analyzer.
When using a relay connector midway, include it in the measurement.
 fDo not use a hub between a twisted-pair-cable transmitter and the projector.
 fDo not pull cables forcefully. Also, do not bend or fold cables unnecessarily.
 fTo reduce the effects of noise as much as possible, stretch out the cables between the t\
wisted-pair-cable transmitter and the projector without any loops.
 fLay the cables between a twisted-pair-cable transmitter and the projecto\
r away from other cables, particularly power cables.
 fWhen installing multiple cables, run them side by side along the shortes\
t distance possible without bundling them together.
 fAfter laying the cables, confirm that the value of [SIGNAL QUALITY] in the [NETWORK] menu → [DIGITAL LINK STATUS] is displayed in green (indicates normal quality). (x page 108)
 fFor twisted-pair-cable transmitter of other manufacturers of which the operation has been verified with the DIGIT AL LINK compatible projector, refer to Panasonic website (http://panasonic.net/avc/projector/). Note that the verification for devices of other manufacturers has been made for the items set by Panasonic Corporation, and not all the operations have been verified. For operation or performance problems caused by the devices of other manufacturers, contact the respe\
ctive manufacturers.
Accessing from the web browser
1) Start up the web browser on the computer.
2) Enter the IP address set on the projector into the URL entry field of the web browser.
3) Enter the user name and the password.
 fThe factory default setting of the user name is user1 (user rights)/admin1 (administrator rights) and the password is panasonic (lower case).
4) Click OK.
 fThe [Projector status] page is displayed.
Note
 fIf you use a web browser to control the projector, set [WEB CONTROL] to [ON] in [NETWORK CONTROL] (x page 109).   
						

							Chapter 4 Settings — [NETWORK] menu
112 - ENGLISH
 fDo not perform setting or control simultaneously by starting up multiple web browsers. Do not set or control the projector from multiple computers. fChange the password first. (x page 121) fThe administrator rights allow use of all functions. The user rights allow use of only the following functions: [Projector status] (x page 112), viewing of the error information page (x page 113), [Network status] (x page 114), [Access error] (x page 114), [Mail error] (x page 114), [Basic control] (x page 115), [Advanced control] (x page 115), [Change password] (x page 121) fAccess will be locked for few minutes when an incorrect password is entered three times consecutively. fSome items on the projector setting page use the Javascript function of the web browser. The projector may not be able to be controlled properly if it is set with a browser that does not have this function en\
abled. fIf the screen for the web control is not displayed, consult your network administrator. fWhile updating the screen for the web control, the screen may become whi\
te for a moment, but it is not a malfunction. fThe subsequent web control screens show examples for PT-EZ580. Screen content may differ from that for the model you are using.
Descriptions of items
1 Page tabPages are switched by clicking this item.
2 [Status]The status of the projector is displayed by clicking this item.
3 [Projector control]The [Projector control] page is displayed by clicking this item.
4 [Detailed set up]The [Detailed set up] page is displayed by clicking this item.
5 [Change password]The [Change password] page is displayed by clicking this item.
6 [Crestron Connected(TM)]The control page of Crestron ConnectedTM is displayed by clicking this item.
[Projector status] page
Click [Status] → [Projector status].
Display the status of the projector for the following items.
1 [PROJECTOR TYPE]Displays the type of the projector.
2 [MAIN VERSION]Displays the firmware version of the projector.
3 [POWER]Displays the status of the power.
4 [SHUTTER] *1
Displays the status of the shutter (ON: closed, OFF: open).
5 [PICTURE MODE]Displays the setting status of [PICTURE MODE].
6 [SERIAL NUMBER]Displays the serial number of the projector.
7 [NETWORK VERSION]Displays the version of the firmware of the network.
8 [REMOTE2 STATUS]Displays the control status of the  terminal.
9 [LAMP POWER]Displays the setting status of [LAMP POWER] (x page 87).
10 [VOLUME]
Display the volume status.
11 [INPUT SELECT]Displays the status of the selected input.
12 [INTAKE AIR TEMPERATURE]Displays the status of the air intake temperature of the projector.
*1 For PT-EZ580, PT-EW640 and PT-EX610 [AV MUTE] for PT-EW540 and PT-EX510 Displays the status of AV mute function.   
						

							Chapter 4 Settings — [NETWORK] menu
ENGLISH - 113
13 [AROUND LAMP TEMPERATURE]Displays the status of the temperature around the lamp of the projector.
14 [LAMP RUNTIME]Displays the runtime of the lamps (converted value).
15 [SELF TEST]Displays the self-diagnosis information.
16 [PROJECTOR RUNTIME]Displays the runtime of the projector.
Error information page
When [Error (Detail)] or [Warning (Detail)] is displayed in the self-diagnosis display of the [Projector status] screen, click it to display the error/warning details.
 fThe projector may go into the standby status to protect the projector de\
pending on the contents of the error.
1 Self-diagnosis result displayDisplays the item check results.[OK]:Indicates that operation is normal.[FAILED]:Indicates that there is a problem.
 r[FAILED] items
ItemDescription
[MAIN CPU BUS]There is a problem with the microcomputer circuitry. Consult your dealer.
[FAN]There is a problem with the fan or the fan drive circuit. Consult your dealer.
[INTAKE AIR TEMPERATURE]The air intake temperature is too high. The projector may be used in an environment where the temperature is high, such as near a heating appliance.
[AROUND LAMP TEMPERATURE]The temperature around the lamp is high. The air exhaust port may be blocked.
[LAMP REMAIN TIME]The runtime of the lamp has exceeded the specified time, and it is time to replace the lamp.
[LAMP STATUS]The lamp has failed to turn on. Wait a while until the luminous lamp cools off, and then turn on the power.
[APERTURE(CONTRAST-SHUTTER)]*1There is a problem in the contrast shutter circuit for iris. Consult your dealer .
[SHUTTER(MUTE-SHUTTER)]*1There is a problem with the shutter circuitry. Consult your dealer.
[INTAKE AIR TEMP.SENSOR]There is a problem with the sensor used to detect intake temperature. Consult your dealer.
[AROUND LAMP TEMP.SENSOR]There is a problem with the sensor used to detect exhaust air temperature. Consult your dealer.
[BATTERY]Battery replacement is required. Consult your dealer.
[AIRFLOW SENSOR]There is a problem with the airflow sensor. Consult your dealer.
[LENS MOUNTER]There is a problem in the lens mounter. Consult your dealer.
[COVER OPEN]Installation of the lamp cover is incomplete. Check the installation of the lamp cover .(x page 131)
[PRESSURE SENSOR]There is a problem with the sensor that detects air pressure. Consult your dealer.
[ANGLE SENSOR]There is a problem with the sensor that detects angle. Consult your dealer.
[FILTER UNIT]The air filter unit is not attached. Check the installation of the air filter unit. (x page 130)
[AIR FILTER]There is too much dust accumulated in the air filter unit. Turn the  switch to  (x page 48), and clean the air filter. (x page 130)
*1 Only for PT-EZ580, PT-EW640 and PT-EX610   
						

							Chapter 4 Settings — [NETWORK] menu
114 - ENGLISH
[Network status] page
Click [Status] → [Network status].
The current network setting status is displayed.
[Access error] page
Click [Status] → [Access error].
The error log on the web server is displayed such as access to the pages that do not exist or access with unauthorized user names or passwords.
[Mail error] page
Click [Status] → [Mail error].
Display E-mail error information if failed to send periodic E-mails.
Note
 f[Access error] and [Mail error] display the recent few hundred accesses/requests. All information may not be displayed when many accesses/requests are made at a time. fWhen information in [Access error] and [Mail error] exceeds a certain amount, older information is erased. fCheck [Access error] and [Mail error] periodically.   
						

							Chapter 4 Settings — [NETWORK] menu
ENGLISH - 115
[Basic control] page
Click [Projector control] → [Basic control].
1
2
4
5
3
6
1 [INPUT] *1
Switches the input signal.
2 [VOLUME]Adjusts the volume.
3 [PICTURE MODE]Switches the picture mode.
4 [SHUTTER] *2
Switches the setting whether to use the shutter function (closing/opening of the shutter).
5 [POWER]Turns on/off the power.
6 [CLOSED CAPTION]Switches the closed caption setting.
*1 [DisplayPort] and [DIGITAL LINK] are only for PT-EZ580, PT-EW640 and PT-EX610)*2 For PT-EZ580, PT-EW640 and PT-EX610 [AV MUTE] for PT-EW540 and PT-EX510 Switches the AV mute function on/off.
[Advanced control] page
Click [Projector control] → [Advanced control].
1
2
1 [POSITION]Operates field angle-related settings.2 [PICTURE]Operates picture quality settings.   
						

							Chapter 4 Settings — [NETWORK] menu
116 - ENGLISH
[Network config] page
Click [Detailed set up] → [Network config].
 fClick [Network config] to display the [CAUTION!] screen.
 fClick the [Next] button to display the current settings.
 fClick the [Change] button to display the setting change screen.
1
2
3
4
5
6
7
8
1 [PROJECTOR NAME]Enter the name of the projector. Enter the host name if it is required when using a DHCP server etc.
2 [DHCP ON], [DHCP OFF]To enable the DHCP client function, set to [DHCP ON].
3 [IP ADDRESS]Enter the IP address when not using a DHCP server.
4 [SUBNET MASK]Enter the subnet mask when not using a DHCP server.
5 [DEFAULT GATEWAY]Enter the default gateway address when not using a DHCP server.
6 [DNS1]Enter the DNS1 server address.Permissible characters for the entry of DNS1 server address (primary):Numbers (0 - 9), period (.)(Example: 192.168.0.253)
7 [DNS2]Enter the DNS2 server address.Available characters for the entry of DNS2 server address (secondary):Numbers (0 - 9), period (.)(Example: 192.168.0.254)
8 [Back], [Change]Click the [Back] button to return to the original screen. The screen for confirming the current settings is displayed by clicking the [Change] button. Click the [Submit] button to update the settings.
Note
 fWhen you use the “Forward” and “Back” functions of your browser, a warning message “Page has Expired” may appear. In that case, click [Network config] again since the following operation will not be guaranteed. fChanging LAN settings while connected to the LAN may cause the connection to cut out.
[Ping test] page
Check whether the network is connected to the E-mail server, POP server, DNS server, etc.
Click [Detailed set up] → [Ping test].
1
23
4
1 [Input IP address]Enter the IP address of the server to be tested.
2 [Submit]Executes the connection test.
3 Example of display when the connection has succeeded
4 Example of display when the connection has failed   
						

							Chapter 4 Settings — [NETWORK] menu
ENGLISH - 117
[Adjust clock] page
Click [Detailed set up] → [Adjust clock].
1
2
3
4
5
6
7
1 [Timezone]Selects the time zone.
2 [Set time zone]Updates the time zone setting.
3 [NTP SYNCHRONIZATION]Sets to [ON] to adjust the date and time automatically.
4 [NTP SERVER NAME]Enter the IP address or server name of the NTP server when you set to adjust the date and time manually.(To enter the server name, the DNS server needs to be set up.)
5 [Date]Enter the date to be changed.
6 [Time]Enter the time to be changed.
7 [Set date and time]Updates the date and time settings.
Note
 fThe replacement of the battery inside the projector is required when the time goes out of alignment right after correcting the time. Consult your dealer.   
						

							Chapter 4 Settings — [NETWORK] menu
118 - ENGLISH
[E-mail set up] page
When there is a problem or the runtime of a lamp reaches a set value, an\
 E-mail can be sent to preset E-mail addresses (up to two addresses).
Click [Detailed set up] → [E-mail set up].
1
2
3
4
5
6
1 [ENABLE]Select [Enable] to use the E-mail function.
2 [SMTP SERVER NAME]Enter the IP address or the server name of the E-mail server (SMTP). To enter the server name, the DNS server needs to be set up.
3 [MAIL FROM]Enter the E-mail address of the projector. (Up to 63 characters in single byte)
4 [MEMO]Enter information such as the location of the projector that notifies the sender of the E-mail. (Up to 63 characters in single byte)
5 [MINIMUM TIME]Change the minimum interval for the temperature warning E-mail. The default value is 60 minutes. In this case, another E-mail will not be sent for 60 minutes after sending the temperature warning E-mail even if it reaches the warning temperature.
6 [INTAKE AIR TEMPERATURE]Change the temperature setting for the temperature warning mail. A temperature warning E-mail is sent when the temperature exceeds this value.
8
787
9
7 [E-MAIL ADDRESS 1], [E-MAIL ADDRESS 2]Enter the E-mail address to be sent. Leave [E-MAIL ADDRESS 2] blank when two E-mail addresses are not to be used.
8 Settings of the conditions to send E-mailSelects the conditions to send E-mail.[MAIL CONTENTS]: Selects either [NORMAL] or [SIMPLE].[ERROR]: Sends an E-mail when an error occurred in the self-diagnosis.[LAMP RUNTIME]: Sends an E-mail when the remaining time for the lamp has reached the value set at the right field.[INTAKE AIR TEMPERATURE]: Sends an E-mail when the air intake temperature has reached the value set at the above field.[PERIODIC REPORT]: Places a check mark on this to send an E-mail periodically.It will be sent on the days and time with the check mark.
9 [Submit]Updates the settings.   
						

							Chapter 4 Settings — [NETWORK] menu
ENGLISH - 119
[Authentication set up] page
Set the authentication items when POP authentication or SMTP authentication is necessary to send an E-mail.
Click [Detailed set up] → [Authentication set up].
1
2
3
4
5
6
78
1 [Auth]Selects the authentication method specified by your Internet service provider.
2 [SMTP Auth]Set when the SMTP authentication is selected.
3 [POP Server name]Enter the POP server name.
Allowed characters:Alphanumerics (A - Z, a - z, 0 - 9)Minus sign (-) and period (.)
4 [User name]Enter the user name for the POP server or the SMTP server.
5 [Password]Enter the password for the POP server or the SMTP server.
6 [SMTP server port]Enter the port number of the SMTP server.(Normally 25)
7 [POP server port]Enter the port number of the POP server.
(Normally 110)
8 [Submit]Updates the settings.
[ECO management set up] page
Settings related to the ECO management function of the projector can be made.
Click [Detailed set up] → [ECO management set up].
1 [LAMP POWER]Selects the [LAMP POWER] setting.
2 [AUTO POWER SAVE]Set to [ON] when setting [AMBIENT LIGHT DETECTION], [SIGNAL DETECTION] and [SHUTTER DETECTION] *1
3 [AMBIENT LIGHT DETECTION]Selects enable ([ON])/disable ([OFF]) of the environmental luminance interlock function.
4 [SIGNAL DETECTION]Selects enable ([ON])/disable ([OFF]) of the no signal interlock function.
5 [SHUTTER DETECTION] *1
Selects enable ([ON])/disable ([OFF]) of the shutter interlock function.
6 [NO SIGNAL SHUT-OFF]When the No signal shut-off function is used, select the time until the standby mode is entered.
7 [Submit]Updates the settings.
*1 For PT-EZ580, PT-EW640 and PT-EX610 [AV MUTE DETECTION] for PT-EW540 and PT-EX510
Note
 fFor details of each setting item, refer to the [PROJECTOR SETUP] menu → [ECO MANAGEMENT] (x page 87) on the projector.   
						

							Chapter 4 Settings — [NETWORK] menu
120 - ENGLISH
Contents of E-mail sent
Example of E-mail sent when E-mail is set
The following E-mail is sent when the E-mail settings have been establis\
hed.
=== P anas onic  pr ojec t or  r epor t ( CO NF I G URE )  ===
P r ojec t or  Ty pe  :  E Z 580
S er ial No :  S N9250024
-----  E-mail set up dat a -----
T E M P E RAT URE  WA RNI NG  S E T UP
MINIMUM TIME  at  [  30]  m inut es  int er v al
I NTA K E  A I R T E M P E RAT URE   O v er  [  36 degC /   96 degF  ]  
E RRO R  [  O N  ]
LA M P  RUNT I M E   [ ON  ]   at REMAIN [ 400] H
LA M P  RUNT I M E   [ ON  ]   at REMAIN [ 500] H
INTAKE AIR T EMPERAT URE  [ O N  ]
P E RI O DI C RE P O RT
S unday   [  O F F  ]   M onday   [  O F F  ]   Tues day   [  O F F  ]   Wednes day  [  O F F  ]
T hur s day   [  O F F  ]   F r iday   [  O F F  ]   S at ur day   [  O F F  ]
00: 00  [  O F F  ]     01: 00  [  O F F  ]     02: 00  [  O F F  ]     03: 00  [  O F F  ]
04: 00  [  O F F  ]     05: 00  [  O F F  ]     06: 00  [  O F F  ]     07: 00  [  O F F  ]
08: 00  [  O F F  ]     09: 00  [  O F F  ]     10: 00  [  O F F  ]     11: 00  [  O F F  ]
12: 00  [  O F F  ]     13: 00  [  O F F  ]     14: 00  [  O F F  ]     15: 00  [  O F F  ]
16: 00  [  O F F  ]     17: 00  [  O F F  ]     18: 00  [  O F F  ]     19: 00  [  O F F  ]
20: 00  [  O F F  ]     21: 00  [  O F F  ]     22: 00  [  O F F  ]     23: 00  [  O F F  ]
-----  check syst em -----
M A I N CP U B US   [   O K   ]
FA N   [   O K   ]
INTAKE AIR T EMPERAT URE  [   O K   ]
ARO UND LAMP T EMPERAT URE  [   O K   ]
LAMP REMAIN T IME  [   O K   ]
LAMP STAT US  [   O K   ]
A P E RT URE (CO NT RA S T-S HUT T E R)  [    O K    ]
S HUT T E R(M UT E -S HUT T E R)  [    O K    ]
INTAKE AIR  T EMP.SENSO R  [   O K   ]
ARO UND LAMP T EMP.SENSO R  [   O K   ]
BAT T ERY  [   O K   ]
AIRF LO W SENSO R  [   O K   ]
LE NS  M O UNT E R  [   O K   ]
CO VER O PEN  [   O K   ]
PRESSURE SENSO R  [   O K   ]
ANG LE SENSO R  [   O K   ]
F I LT E R UNI T  [   O K   ]
A I R F I LT E R  [   O K   ]
( E r r or  c ode00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00)
I nt ak e air  t em per at ur e  :   45 degC /  113 degF
A r ound lam p t em per at ur e  :   42 degC /  107 degF
P RO JE CTO R RUNT I M E   2500 H
LAMP ECO   100 H
LAMP NO RMAL  200 H
LAMP REMAIN  1900 H
--------  Current  st at us --------
MAIN VERSIO N  1.00
NET WO RK VERSIO N  1.00
SUB VERSIO N  1.00
LAMP STAT US  LAMP=O N 
I NP UT S I G NA L  HDM I
SIG NAL NAME  XG A60
S I G NA L F RE Q UE NCY   65. 4k Hz  /  54. 4Hz
REMO T E2 STAT US  ENABLE
----- Wired Net work conf igurat ion -----
DHCP  Client   O F F
I P  addr es s   192. 168. 0. 8
M A C addr es s   c c : 7e: e8: 00: 00: 00
Tue J un 04 22: 30: 14: 2013
----- Memo -----
Note
 fAPERTURE(CONTRAST-SHUTTER) and SHUTTER(MUTE-SHUTTER) are only for PT-EZ580, PT-EW640 and PT-EX610.