Panasonic Projector PT-EW640 User Manual

							Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 91
[PROJECTOR]Use the  terminal of the projector to execute RS-232C communication.
[DIGITAL INTERFACE BOX]Executes RS-232C communication via the optional Digital Interface Box (Model No.: ET-YFB100G) and the  terminal.
5) Press as to select [BAUDRATE].
6) Press qw to switch the item.
 fThe items will switch each time you press the button.
[9600]
Select the proper speed.[19200]
[38400]
7) Press as to select [PARITY].
8) Press qw to switch the item.
 fThe items will switch each time you press the button.
[NONE]
Select the parity condition.[EVEN]
[ODD]
Setting the control commands of an existing projector
When controlling the projector on a computer, set use of control commands on a previously purchased Panasonic projec\
tor. This allows the control software for an existing Panasonic projector to be inherited and used.
1) Press as to select [RS-232C].
2) Press the  button.
 fThe [RS-232C] screen is displayed.
3) Press as to select [EMULATE].
4) Press the  button.
5) Press as to select an item.
[DEFAULT]EZ580 series, EW640 series, EX610 series, EW540 series, EX510 series, VW345N series, VX415N series, VW340Z, VX410Z, VX42Z, VX406EA, VX46EA, EZ770 series, EW730 series, EX800 series, RZ475 series, RZ470 series, RW430 series, RZ370 series, RW330 series
[D3500]D3500 series
[D4000]D4000 series
[D/W5k SERIES]D5700 series, DW5100 series, D5600 series, DW5000 series, D5500 series
[D/W/Z6k SERIES]DZ770 series, DW740 series, DX810 series, DZ680 series, DW640 series, DX610 series, DW730 series, DX800 series, DZ6710 series, DZ6700 series, DW6300 series, D6000 series, D5000 series, DZ570 series, DW530 series, DX500 series
[L730 SERIES]L730 series, L720 series, L520 series
[L780 SERIES]L780 series, L750 series
[L735 SERIES]L735 series
[L785 SERIES]L785 series
[F/W SERIES]FW430 series, FX400 series, FW300 series, F300 series, F200 series, FW100 series, F100 series
[LZ370]LZ370 series
[LB/W SERIES]LB3 series, LB2 series, LB1 series, ST10 series, LB90 series, LW80NT series, LB80 series, LB78 series, LB75 series
[VX500 SERIES]VW435N series, VW440 series, VW430 series, VX505N series, VX510 series, VX501U, VX405KEA, VX45KEA, VX500 series, VW330 series, VX400NT series, VX400 series, VX41 series
[EZ570 SERIES]EZ570 series, EW630 series, EW530 series, EX600 series, EX500 series
[VW431D]VW431D series
6) Press the  button.
7) When the confirmation screen is displayed, press qw to select [OK], and press the  button.   
						

							Chapter 4 Settings — [PROJECTOR SETUP] menu
92 - ENGLISH
Note
(Only for PT-EZ580, PT-EW640 and PT-EX610)
 fWhen [INPUT SELECT] is set to [DIGITAL INTERFACE BOX], communication using that serial terminal is available only when the corresponding device (such as the optional Digital Interface Box (Model No.: ET-YFB100G)) is connected to the  terminal. fWhen transferring logos via the optional Digital Interface Box (Model No.: ET-YFB100G), “NO SIGNAL SLEEP” of ET-YFB100G must be set to “OFF” to avoid cutting off communication. fWhen [INPUT SELECT] is set to [DIGITAL INTERFACE BOX], communication speed is fixed to 9 600 bps.
[REMOTE2 MODE]
Set the  terminal.
1) Press as to select [REMOTE2 MODE].
2) Press qw to switch the item.
 fThe items will switch each time you press the button.
[DEFAULT]The pin assignment of the  terminal is used by the factory default setting of the projector.
[USER]Used to change the setting of the  terminal.
[F/W SERIES]The setting of the  terminal is used for the F/W series compatibility .
 fWhen [USER] is selected, proceed to Step 3).
3) Press the  button.
4) Press as to select one from [PIN2] to [PIN8], and press qw to switch the setting.
[FUNCTION BUTTON]
Set the functions of the  button on the remote control.
1) Press as to select [FUNCTION BUTTON].
2) Press the  button.
 fThe [FUNCTION BUTTON] screen is displayed.
3) Press as to select a function.
[DISABLE]Disables the  button.
[SUB MEMORY]Displays the sub memory list. (x page 103)
[SYSTEM SELECTOR]Switches the [SYSTEM SELECTOR] setting. (x page 66)
[DAYLIGHT VIEW]Switches the [DAYLIGHT VIEW] setting. (x page 66)
[TEST PATTERN]Displays the test pattern built-in to the projector. (x page 100)
4) Press the  button.
[AUDIO SETTING]
Set audio functions in detail.
Adjusting the volume
1) Press as to select [AUDIO SETTING].
2) Press the  button.
 fThe [AUDIO SETTING] screen is displayed.
3) Press as to select [VOLUME].
4) Press qw to adjust the level.
OperationAdjustmentRange of adjustment
Press w.Increases the volume.0 - 63Press q.Decreases the volume.   
						

							Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 93
Adjusting the left to right audio balance
1) Press as to select [AUDIO SETTING].
2) Press the  button.
 fThe [AUDIO SETTING] screen is displayed.
3) Press as to select [BALANCE].
4) Press qw to adjust the level.
OperationAdjustmentRange of adjustment
Press w.Increases the volume on the right.L16 - R16Press q.Increases the volume on the left.
Setting audio output of the built-in speaker
1) Press as to select [AUDIO SETTING].
2) Press the  button.
 fThe [AUDIO SETTING] screen is displayed.
3) Press as to select [BUILT-IN SP].
4) Press qw to switch the item.
 fThe items will switch each time you press the button.
[ON]Audio is output from the built-in speaker.
[OFF]Audio is not output from the built-in speaker.
Note
 fAudio is output from the built-in speaker even if the cable is connected to the  terminal. To output audio from external audio devices connected to the  terminal and not from the built-in speaker, set [BUILT-IN SP] to [OFF].
Setting audio output in the standby mode
1) Press as to select [AUDIO SETTING].
2) Press the  button.
 fThe [AUDIO SETTING] screen is displayed.
3) Press as to select [IN STANDBY MODE].
4) Press qw to switch the item.
 fThe items will switch each time you press the button.
[OFF]Audio is not output during standby.
[ON]Audio is output during standby.
Note
 fWhen [STANDBY MODE] (x page 88) in [PROJECTOR SETUP] menu → [ECO MANAGEMENT] is set to [ECO], audio cannot be output during standby.
Setting to mute mode
1) Press as to select [AUDIO SETTING].
2) Press the  button.
 fThe [AUDIO SETTING] screen is displayed.
3) Press as to select [MUTE].
4) Press qw to switch the item.
 fThe items will switch each time you press the button.   
						

							Chapter 4 Settings — [PROJECTOR SETUP] menu
94 - ENGLISH
[OFF]Audio is not output.
[ON]Audio is output.
Setting audio input from a connected device
1) Press as to select [AUDIO SETTING].
2) Press the  button.
 fThe [AUDIO SETTING] screen is displayed.
3) Press as to select the audio input.
4) Press qw to switch the item.
 fThe items will switch each time you press the button.
[AUDIO IN 1]Audio connected to the  terminal is output at projection of images from a preset input terminal.
[AUDIO IN 2]Audio connected to the  terminal is output at projection of images from a preset input terminal.
[AUDIO IN 3]Audio connected to the  terminal is output at projection of images from a preset input terminal.
[HDMI AUDIO IN]*1HDMI audio is output.
[DIGITAL LINK AUDIO IN]*2DIGITAL LINK audio is output.
[DisplayPort AUDIO IN]*3DisplayPort audio is output.
*1 Only when the input is HDMI
*2 Only for PT-EZ580, PT-EW640 and PT-EX610 Only when the input is DIGITAL LINK
*3 Only for PT-EZ580, PT-EW640 and PT-EX610 Only when the input is DisplayPort
[STATUS]
Display the status of the projector.
1) Press as to select [STATUS].
2) Press the  button.
 fThe [STATUS] screen is displayed.
3) Press qw to switch the pages.
 fThe page will change each time you press the button.
[INPUT]Displays the input terminal currently selected.
[SIGNAL NAME]Displays the input signal name.
[SIGNAL FREQUENCY]Displays the frequency of the input signal.
[PROJECTOR RUNTIME]Displays the operation times of the projector.
[LAMP : ECO]Displays the lamp runtime when [LAMP POWER] is set to [ECO] by actual time.
[LAMP : NORMAL]Displays the lamp runtime when [LAMP POWER] is set to [AUTO] and [NORMAL] by actual time.
[LAMP : TOTAL] *1Converts the cumulative lamp runtime into the runtime when set to [NORMAL], and displays the converted runtime.
[INTAKE AIR TEMP.]Displays the status of the air intake temperature of the projector.
[AROUND LAMP TEMP.]Displays the status of the temperature around the lamp of the projector .
[PROJECTOR TYPE]Displays the type of the projector.
[SERIAL NUMBER]Displays the serial number of the projector.
[LAMP UNIT MODEL NO.]Displays the model no. of the lamp unit.
[LAMP SERIAL NUMBER]Displays the serial number of the lamp.
[MAIN VERSION]Displays the main version of the firmware of the projector.
[SUB VERSION]Displays the sub version of the firmware of the projector.
[NETWORK VERSION]Displays the network version of the projector.
[EMULATE]Displays the [EMULATE] settings.
[ON COUNT]
[POWER ON TIMES]Displays the number of times the power is turned on.
[LAMP ON]Displays the number of times the lamp is turned on.
[SHUTTER] *2Displays the number of times the shutter is closed.   
						

							Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 95
[NUMBER OF REGISTERED SIGNAL]Displays the number of registered signals.
[REMOTE2 STATUS]Displays the control status of the REMOTE2.
[SIGNAL INFORMATION]
[MEMORY NO.]Displays the memory number of the input signal.
[INPUT]Displays the input terminal currently selected.
[SIGNAL NAME]Displays the input signal name.
[SIGNAL FREQUENCY]Displays the frequency of the input signal.
[SYNC.STATE]Displays the synch polarity of the input signal.
[V.SYNC WIDTH]Displays the vertical sync signal pulse width of the input signal.
[SCAN TYPE]Displays the scan type of the input signal.
[TOTAL DOTS]Displays the total dot count of the input signal.
[DISPLAY DOTS]Displays the number of input signal display dots.
[TOTAL LINES]Displays the total line count of the input signal.
[DISPLAY LINES]Displays the number of input signal display lines.
[SAMPLING]Displays the sampling information of the input signal.
[SIGNAL LEVEL]Displays the signal level of the input signal.
*1 The lamp runtime displayed is calculated internally by the following con\
versions.
Formula for lamp replacement time (rough estimate)
Lamp runtime displayed in [LAMP : TOTAL]
(A x 9 + B x 8) ÷ 9 fA: Runtime when [LAMP POWER] is set to [AUTO] and [NORMAL]
 fB: Runtime when [LAMP POWER] is set to [ECO]
*2 Only for PT-EZ580, PT-EW640 and PT-EX610
Note
 fThe content of status can be sent via E-mail by pressing the  button while displaying the [STATUS] screen. fSome items in [SIGNAL INFORMATION] may be displayed and others not displayed, depending on the signal being input.
[DATE AND TIME]
Set the time zone, date, and time of the built-in clock of the projector.
Setting the time zone
1) Press as to select [DATE AND TIME].
2) Press the  button.
 fThe [DATE AND TIME] screen is displayed.
3) Press as to select [TIME ZONE].
4) Press qw to switch [TIME ZONE].
Setting the date and time manually
1) Press as to select [DATE AND TIME].
2) Press the  button.
 fThe [DATE AND TIME] screen is displayed.
3) Press as to select [ADJUST CLOCK].
4) Press the  button.
 fThe [ADJUST CLOCK] screen is displayed.
5) Press as to select an item, and press qw to set the local date and time.
6) Press as to select [APPLY], and press the  button.
 fThe setting of the date and time will be completed.
Setting the date and time automatically
1) Press as to select [DATE AND TIME].   
						

							Chapter 4 Settings — [PROJECTOR SETUP] menu
96 - ENGLISH
2) Press the  button.
 fThe [DATE AND TIME] screen is displayed.
3) Press as to select [ADJUST CLOCK].
4) Press the  button.
 fThe [ADJUST CLOCK] screen is displayed.
5) Press as to select [NTP SYNCHRONIZATION], and press qw to change the setting to [ON].
6) Press as to select [APPLY], and press the  button.
 fThe setting of the date and time will be completed.
Note
 fTo set the date and time automatically, the projector must be connected to the network. fIf synchronization with the NTP server fails just after [NTP SYNCHRONIZATION] is turned [ON], or if [NTP SYNCHRONIZATION] is turned [ON] while the NTP server is not set, [NTP SYNCHRONIZATION] will return to [OFF]. fAccess the projector via a web browser to set the NTP server. Refer to “[Adjust clock] page” (x page 117) for details.
[SAVE ALL USER DATA]
Save the various setting values as a backup in the built-in memory of the projector.
1) Press as to select [SAVE ALL USER DATA].
2) Press the  button.
 fThe [SECURITY PASSWORD] screen is displayed.
3) Enter a security password and press the  button.
4) When the confirmation screen is displayed, press qw to select [OK], and press the  button.
 f[PROGRESS] is displayed while saving data.
Note
 fData set from the computer application is not included in [ALL USER DATA].
[LOAD ALL USER DATA]
Load the various setting values saved as a backup in the built-in memory\
 of the projector.
1) Press as to select [LOAD ALL USER DATA].
2) Press the  button.
 fThe [SECURITY PASSWORD] screen is displayed.
3) Enter a security password and press the  button.
4) When the confirmation screen is displayed, press qw to select [OK], and press the  button.
Note
 fThe projector will go into the standby mode to reflect the setting values when [LOAD  ALL USER DATA] is executed. fData registered from a computer is not included in [ALL USER DATA].
[INITIALIZE]
Return various setting values to their factory default settings.
1) Press as to select [INITIALIZE].
2) Press the  button.
 fThe [SECURITY PASSWORD] screen is displayed.
3) Enter a security password and press the  button.
 fThe [INITIALIZE] screen is displayed.
4) Press as to select an item to initialize.
[ALL USER DATA]Returns all setting items including [REGISTERED SIGNAL], [NETWORK SETUP], [E-mail set up], and [USER LOGO] to the factory default settings.The projector will go into the standby status to reflect the setting values.   
						

							Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 97
[REGISTERED SIGNAL]Deletes all the setting values saved for each input signal.To delete only a part of a registered signal, perform the procedure descr\
ibed in “Deleting the registered signal” (x page 102).
[NETWORK/E-MAIL]Returns [NETWORK SETUP] and [E-mail set up] to factory default settings.
[LOGO IMAGE]Deletes the image registered in [USER LOGO].
5) Press the  button.
6) When the confirmation screen is displayed, press qw to select [OK], and press the  button.
[SERVICE PASSWORD]
This function is used by a service person.   
						

							Chapter 4 Settings — [P IN P] menu
98 - ENGLISH
[P IN P] menu
On the menu screen, select [P IN P] from the main menu, and select an item from the sub-menu.Refer to “Navigating through the menu” (x page 57) for the operation of the menu screen. fAfter selecting the item, press asqw to set.
Using P IN P function
Locate a separate, small sub screen in the main screen to project two im\
ages simultaneously.
1) Press as to select [P IN P MODE].
2) Press the  button.
 fThe [P IN P MODE] screen is displayed.
3) Press as to select a function.
[OFF]P IN P function is not used.
[USER1]
The items set in “Setting P IN P function” (x page 98) are used in P IN P function.[USER2]
[USER3]
4) Press the  button.
Setting P IN P function
P IN P function settings can be saved to [USER1], [USER2], and [USER3].
1) Press as to select [P IN P MODE].
2) Press the  button.
 fThe [P IN P MODE] screen is displayed.
3) Press as to select the desired mode from [USER1], [USER2], and [USER3], and press the  
button.
4) Press the  button.
5) Press as to select [MAIN WINDOW] or [SUB WINDOW], and press the  button.
6) Press as to select the input terminal to be displayed in the window, and press the  button.
7) Press the  button.
8) Press as to select an item.
[SIZE]Set the window display size between 10 % and 100 %.
[POSITION]Set the display position of the window within the screen.
[CLOCK PHASE]When the sub window is input from the  terminal or the  terminal and a flickering image or smeared outline appears, set between 0 and +31.
9) If [SIZE] is selected in Step 8), press the  button.
 fThe sub-menu is displayed.
10) Press as to select an item.
11) Press qw to make adjustment, and press the  button.
12) If [POSITION] is selected in Step 8), press the  button.
13) Press asqw to adjust the position, and press the  button.   
						

							Chapter 4 Settings — [P IN P] menu
ENGLISH - 99
14) If [CLOCK PHASE] is selected in Step 8), press qw to make adjustment.
15) Press as to select [FRAME LOCK].
16) Press qw to switch the item.
[MAIN WINDOW]Set frame lock to the input signal set in the main window.
[SUB WINDOW]Set frame lock to the input signal set in the sub window.
17) Press as to select [TYPE].
18) Press qw to switch the item.
[MAIN WINDOW]The main window has display priority.
[SUB WINDOW]The sub window has display priority.
Note
 fThe P IN P function may not be available for some signals being input or terminals being selected. Refer to “Two-window display combination list” (x page 144) for details. fThe main window setting values are applied to image adjustment values such as [PICTURE MODE], [GAMMA], and [COLOR TEMPERATURE]. fOn the normal screen (when no menu is displayed), press as to switch the size and position of the main window and sub window while\
 P IN P is operating. fIf the signals from the  or  terminal are input to either the main window or the sub window, and those input signals are analog RGB or YCBCR/YPBPR signals, the signals are output from the  terminal. If input combination of the main 
window and sub window is RGB1 and RGB2, the signals of the main window take priority for output.   
						

							Chapter 4 Settings — [TEST PATTERN] menu
100 - ENGLISH
[TEST PATTERN] menu
On the menu screen, select [TEST PATTERN] from the main menu.Refer to “Navigating through the menu” (x page 57) for the operation of the menu screen. fPress qw to switch.
[TEST PATTERN]
Display the test pattern built-in to the projector.
Settings of position, size, and other factors will not be reflected in test patterns. Make sure to display the input signal before performing various adjustments.
1) Press qw to switch the [TEST PATTERN] item.
 fThe items will switch each time you press the button.
Menu screen + Color bar (vertical)
Displays test patterns with the menu screen. Select a test pattern so that it is easy to make various adjustments.
Menu screen + Color bar (horizontal)
Menu screen + 16 gradations (vertical 1)
Menu screen + 16 gradations (vertical 2)
Menu screen + 16 gradations (horizontal 1)
Menu screen + 16 gradations (horizontal 2)
Menu screen + Cross hatch
Menu screen + Aspect frame
Menu screen + All white
Menu screen + All black
Menu screen + Entry screenDisplays the menu screen and input signal.Built-in test patterns are not displayed.
Note
 fPress the  button on the remote control while the test pattern is displayed to hide the menu screen.