Panasonic Projector Pt Dw730ul Operating Instructions

[PROJECTOR SETUP] menu 
ENGLISH - 61
Settings
[PROJECTOR SETUP] menu 
Select [PROJECTOR SETUP] from the main 
menu, and select the item from the sub-menu. 
Refer to “
Navigating through the menu ”
 
(
 page 41) regarding the operation of the menu 
screen.   
z
After selecting the item, press ÛÝ/¢/£ to set. 
[PROJECTOR ID]
The projector has an ID number setting function, and 
simultaneous control or individual control is possible 
with one remote control when multiple projectors are 
used side by side....

[PROJECTOR SETUP] menu 
62 - ENGLISH
Settings
3)  When the confirmation is displayed, select [OK] or [CANCEL], and press 
the  button. 
Note
 
z
The speed of the fan is raised and the operation 
sound will become louder when this is set to [ON]. 
[COOLING CONDITION]
You can change the fan control depending on the 
direction of projection. 
Set [COOLING CONDITION] correctly in accordance 
with the direction of projection referencing the 
following figure. It may shorten the life of the lamp if 
u

sed in...

[PROJECTOR SETUP] menu 
ENGLISH - 63
Settings
[LAMP RELAY]
The degradation of the lamp due to continuous usage 
can be reduced by automatically switching the lamp 
to be turned on when using the projector continuously 
for 22 hours or more. 
1)  Press ▲▼ to select [LAMP RELAY]. 
2)  Press ◀▶ to switch [LAMP RELAY]. 
 
z
The time setting to switch the lamp will change 
as follows each time you press the button. 
[OFF][00:00]
(Every one 
hour)
[23:00][01:00]
Note  
z
The   LAMP RELAY¡  function will be...

[PROJECTOR SETUP] menu 
64 - ENGLISH
Settings
[REMOTE2 MODE]
You can set the  terminal. 
1)  Press ▲▼ to select [REMOTE2 MODE]. 
2)  Press ◀▶ to switch [REMOTE2  MODE]. 
 
z
The setting will change as follows each time 
you press the button.
[DEFAULT][USER]
[DEFAULT] The pin assignment of the 
 terminal is used 
by the factory default setting of the 
projector. 
(
 page 100)
[USER] Used to change the setting of the 
 terminal. 
 
■ When selecting [USER] in Step 2)
3)  Press the  button.
4)  Press 
▲▼...

[PROJECTOR SETUP] menu 
ENGLISH - 65
Settings
[NO SIGNAL SHUT-OFF]
You can set the power of the projector automatically 
to standby if there is no input signal by the specified 
time. 
1)  Press ▲▼ to select [NO SIGNAL SHUT-
OFF]. 
2)  Press ◀▶ to switch [NO SIGNAL  SHUT-OFF]. 
[DISABLE] Disables [NO SIGNAL SHUT-
OFF]. 
[10MIN.] -  [90MIN.] Allows you to set in ten minute 
intervals. 
[FUNCTION BUTTON]
You can set the  button on the remote 
control. 
1)  Press ▲▼ to select [FUNCTION 
BUTTON]. 
2)  Press...

[PROJECTOR SETUP] menu 
66 - ENGLISH
Settings
[LOAD ALL USER DATA]
You can load the various setting values saved as a 
backup in the built-in memory of the projector. 
1)  Press ▲▼ to select [LOAD ALL USER 
DATA]. 
2)  Press the  button. 
 
z
The [SECURITY PASSWORD] screen is 
displayed. 
3)  Enter the security password and press 
the  button.
4)  When the confirmation is displayed,  select [OK] or [CANCEL], and press 
the  button.
Note
 
z
The  projector will go into the standby status to 
r

eflect the...

[TEST PATTERN] menu 
ENGLISH - 67
Settings
[TEST PATTERN] menu 
Select [TEST PATTERN] from the main menu. 
Refer to “
Navigating through the menu ”
 
(
 page 41) regarding the operation of the menu 
screen.   
z
Press /¢/£ to switch. 
[TEST PATTERN]
Displays the test pattern built-in to the projector. 
Results of position setting, size, etc. will not be 
reflected in the test patterns. Make sure to display the 
input signal before performing various adjustments. 
Press ◀▶ to switch the various test...

[SIGNAL LIST] menu 
68 - ENGLISH
Settings
Select [SIGNAL LIST] from the main menu. 
Refer to “
Navigating through the menu ”
 
(
 page 41) regarding the operation of the menu 
screen. 
 
■ Registered signal status
 
z
The name can be set for each sub memory 
(
 page 69). 
 
z
Memory number: A1 (1-2)
Sub memory number
When the address number (A1, A2, ... H7, 
H8) is registered 
Registering a signal to the list 
After a new signal is input and the  button 
on the remote control or the control panel is...

[SIGNAL LIST] menu 
ENGLISH - 69
Settings
Managing the sub memory list 
The projector has a sub memory function that can 
register the multiple image adjustment data, even if it 
is recognized as the same signal by the frequency or 
format of the synchronization signal source. 
Use this function when you need to adjust the picture 
quality such as switching of the aspect ratio or white 
balance by the same synchronization signal source. 
The sub memory includes all the data that can be 
a

djusted for...

[SECURITY] menu 
70 - ENGLISH
Settings
[SECURITY] menu 
Select [SECURITY] from the main menu, and select 
the item from the sub-menu. 
Refer to “
Navigating through the menu ”
 
(
 page 41) regarding the operation of the menu 
screen.   
z
When the projector is used for the first time
Initial password: Press Û/£Ý/¢Û/£Ý/¢ in 
order, and press the  button. 
 
z
After selecting the item, press ÛÝ/¢/£ to set. 
Attention
 
z
Make the settings after displaying the [SECURITY] 
screen.
 
z
When the...