Panasonic Projector PT-DS20KU User Manual

							[ADVANCED MENU]
ENGLISH - 81
Settings
[INPUT RESOLUTION]
You can adjust to achieve an optimal image when 
there is a flickering image or smeared outlines.
1) Press ▲▼ to select [INPUT 
RESOLUTION].
2)
 
Press the  button.
▶z The  [INPUT RESOLUTION]
 screen is 
displayed.
3) Press  ▲▼ to select [T
OTAL DOTS], 
[DISPLAY DOTS], [TOTAL LINES], or 
[DISPLAY LINES], and press  ◀▶ to 
adjust it.
▶z Values corresponding to the input signal are 
displayed automatically for each item. Change 
the displayed values and adjust to the optimal 
point viewing the screen when there is a vertical 
banding or missing in the screen.
Note
 z P

reviously mentioned vertical banding will not occur 
with all white signal input.
 z The image may be disrupted while performing the 
adjustment, but it is not a malfunction.
 z[INPUT

 RESOLUTION] can be adjusted only when 
a signal is input to the  terminal or the 
 terminal.
 z Certain signals may not be adjustable.
[CLAMP POSITION]
You can adjust the optimal point when the black part 
of the image is blunt or it has turned green.
1) Press 
▲▼ to select [CLAMP
 
POSITION].
2)
 
Press  ◀▶ to adjust the level.
▶z
Adjust the level to a value from [1] to [255].
 zOptimal value of clamp position adjustment
When the black part is blunt:
The point where bluntness of the black part 
improves the most is the optimal value.
When the black part is green:
The point where the green part becomes black, 
and the bluntness has improved is the optimal 
value.
Note
 z [CLAMP

 POSITION] can be adjusted only when a 
signal is input to the  terminal or the 
 terminal.
 z Certain signals may not be adjustable.
[EDGE BLENDING]
The edge blending function allows multiple projector 
images to be seamlessly overlapped by using the 
inclination of the brightness at the overlapped area.
1) Press 
▲▼ to select [EDGE 
BLENDING].
2)
 
Press  ◀▶ to switch [EDGE 
BLENDING].
▶z The setting will change as follows each time 
you press the button.
[OFF][ON][USER]
[OFF] Sets the edge blending function to 
off.
[ON] Use the setting value of the internal 
distortion of the set for the inclination 
of the edge blending area.
[USER] Use the user-setting value for the 
inclination of the edge blending area. 
(Configuration/registration requires 
separate software. Consult your 
dealer.)
3) Select [ON] or [USER] in Step 2), and 
press the  button.
▶z
The  [EDGE BLENDING] screen is displayed.
4) Press 
▲▼ to specify the location to be 
corrected.
▶z When joining at top: Set [UPPER] to [ON].
▶zWhen joining at bottom: Set [LOWER] to [ON].
▶zWhen joining at left: Set [LEFT] to [ON].
▶zWhen joining at right: Set [RIGHT] to [ON].
5) Press 
◀▶ to switch [ON] and [OFF].
6)  
Press  ▲▼ to select [ST

ART] and 
[WIDTH].
7)
 
Press  ◀▶ to adjust correction width 
and starting point. 
						

							[ADVANCED MENU]
82 - ENGLISH
Settings
▶■To display the adjustment marker
8) Press 
▲▼ to select [MARKER].
9)  
Press  ◀▶ to switch [ON].
▶z
A marker for image position adjustment is 
displayed. The position where the red and 
green lines overlap for the sets to join will be 
the optimal point.
Make sure to set the correction width for the 
sets to join as the same value. Optimal joining 
is not possible with the sets with different 
correction widths.
The optimal point \Ris the point where\R this line overlap\Rs.
Green line
Re\f line
10) Press  ▲▼ to select [BRIGHTNESS 
ADJUST].
11) Press the  button.
▶z The  [BRIGHTNESS ADJUST] screen is 
displayed.
▶z By setting [AUT

O TESTPATTERN] on the 
[EDGE BLENDING] screen to [ON], the black 
test pattern is displayed when you enter the 
[BRIGHTNESS ADJUST] screen.
12) Press  ▲▼ to select [NON-
OVERLAPPED BLACK LEVEL].
13) Press the  button.
▶z The  [NON-OVERLAPPED BLACK LEVEL] 
screen is displayed.
▶z When [INTERLOCKED] is set to [OFF], [RED], 
[GREEN], and [BLUE] can be adjusted.
14) Press 
▲▼ to select an item, and 
press  ◀▶ to adjust the setting.
▶z
Once the adjustment is completed, press the 
 button to return to the 
[BRIGHTNESS 
ADJUST] screen.
15) Press  ▲▼ to select [UPPER], 
[LOWER], [LEFT], or [RIGHT] in 
[BLACK BORDER WIDTH].
16) Press  ◀▶ to set the region (width) 
of the [BLACK BORDER WIDTH] 
adjustment.
▶z When PT -DZ21KU or PT-DS20KU is used, 
proceed to Step 17).
▶z When PT

-DW17KU is used, proceed to Step 
19).
17) Press  ▲▼ to select [UPPER 
KEYSTONE AREA], [LOWER 
KEYSTONE AREA], [LEFT KEYSTONE 
AREA], or [RIGHT KEYSTONE AREA].
18) Press  ◀▶ to adjust the tilt of the 
border between [NON-OVERLAPPED 
BLACK LEVEL] and [BLACK BORDER 
LEVEL].
19) Press  ▲▼ to select [BLACK BORDER 
LEVEL].
20) Press the  button.
▶z The  [BLACK BORDER LEVEL] screen is 
displayed.
▶z When [INTERLOCKED] is set to [OFF], [RED], 
[GREEN], and [BLUE] can be adjusted.
21) Press 
▲▼ to select an item, and 
press  ◀▶ to adjust the setting.
>%/$&.%25(5:,7+@5LJKW
3URMHFWLRQUDQJH
(GJHEOHQGLQJ>:,7+@5LJKW
>0$5.(5@5HG
(GJHEOHQGLQJ>67$57@5LJKW
>0$5.(5@*UHHQ
>%/$&.%25(5/(9(/@ >29(5/$33(%/$&./(9(/@5LJKW
>12129(5/$33(%/$&./(9(/@
Note
 z The [BRIGHTNESS 

ADJUST] function makes it 
harder to notice the black level of the part of the 
image overlapping getting brighter when multiple 
screens are set using [EDGE BLENDING]. The 
optimal point of the correction is set by adjusting 
[NON-OVERLAPPED BLACK LEVEL] so the black 
level of the overlapping image area will be the 
same level as the non-overlapping area.
If the bordering part of the part where the image 
is overlapping and the non-overlapping part gets 
brighter after adjusting [NON-OVERLAPPED 
BLACK LEVEL], adjust the width of the top, bottom, 
left, or right. Adjust [BLACK BORDER LEVEL] 
when the width adjustment makes only the border 
area darker.
 z The joining part may look discontinuous depending 
on the position you are looking from when a screen 
with high gain or rear screen is used.
 zWhen configuring multiple screens using 
both horizontal and vertical edge blending 
simultaneously

, adjust [OVERLAPPED BLACK 
LEVEL] first before making adjustments in Step 
12). Adjustment method is same as the procedure 
of [NON-OVERLAPPED BLACK LEVEL].
 z T

o use either horizontal or vertical edge blending 
only, set all values of [OVERLAPPED BLACK 
LEVEL] to 0. 
						

							[ADVANCED MENU]
ENGLISH - 83
Settings
 zThe [AUTO TESTPATTERN] settings change in 
conjunction with the [AUTO TESTPATTERN] in 
[COLOR MATCHING].
 z Adjustment of the tilt of the border between [NON-
OVERLAPPED BLACK LEVEL] and [BLACK 
BORDER LEVEL] is a function to perform the 
adjustment of [GEOMETR

Y] (
 page 76) together 
with the edge blending. If [NON-OVERLAPPED 
BLACK LEVEL] is tilted by correcting the keystone 
distortion from [KEYST
ONE] in [GEOMETRY], 
perform Steps 17) and 18) to adjust the edge 
blending according to the shape of [NON-
OVERLAPPED BLACK LEVEL].
 z W

hen the keystone is corrected using [KEYSTONE], 
the edge blending cannot be adjusted together. 
(Only for PT-DW17KU)
[FRAME RESPONSE]
Image processing is simplified when 1080/60i, 
1080/50i, and 1080/24sF signals are input to reduce 
image frame delay.
1) Press  ▲▼ to select [FRAME 
RESPONSE].
2)
 
Press  ◀▶ to switch [FRAME 
RESPONSE].
▶z The setting will change as follows each time 
you press the button.
[NORMAL][FAST]
[NORMAL]
Standard setting.
[FAST] Set when the picture is displayed 
later than sound.
Note
 z When [FRAME RESPONSE] is set to [F

AST], 
picture quality deteriorates. Digital cinema quality 
and P IN P functions also cannot be used.
[FRAME LOCK] (PT- DZ21KU and 
PT
-

DS20KU only)
Set this to view 3D display when the scanning 
frequency of the signal is 25 Hz, 50 Hz, and 100 Hz.
1) Press  ▲▼ to select [FRAME LOCK].
2)  
Press  ◀▶ to switch [FRAME LOCK].
▶z
The setting will change as follows each time 
you press the button.
[OFF][ON]
[OFF]
Decreases the flickering.
[ON] Synchronizes the display to the 
scanning frequency of the input 
signal.
Note
 z [

FRAME LOCK] is not displayed when the scanning 
frequency of the signal other than above is input or 
2D images are displayed.
 z The screen may flicker when the [FRAME LOCK] is 
set to [ON].
 zThe display may look discontinuous when the 
[FRAME LOCK] is set to [OFF].
[RASTER POSITION]
This will allow the position of the image to move within 
the display area arbitrarily when the input image is not 
using the whole display area.
1) Press 
▲▼ to select [RASTER 
POSITION].
2)
 
Press the  button.
▶z The  [RASTER POSITION]
 screen is displayed.
3) Press 
▲▼◀▶  to adjust the position. 
						

							[DISPLAY LANGUAGE] menu
84 - ENGLISH
Settings
Select [DISPLAY LANGUAGE] from the main 
menu, and display the sub-menu.
Refer to “Navigating through the menu” 
(
 page 63) for the operation of the menu 
screen.
 z Press 
▲▼ to select a language, and press the 
 button to set.
Changing the display 
language
You can select the language of the on-screen display.
ENTER
DISPLAY LANGUAGE
SELECT
SET
 zVarious menus, settings, adjustment screens, 
control button names, etc., are displayed in the 
selected language.
 z The language can be changed to English, German, 
French, Spanish, Italian, Portuguese, Japanese, 
Chinese, Russian, and Korean.
Note
 z The on-screen display language of the projector is 
set to English by default. (Factory default)
[DISPLAY LANGUAGE] menu 
						

							[3D SETTINGS] menu (PT-DZ21KU and PT- DS20KU only)
ENGLISH - 85
Settings
[3D SETTINGS] menu (PT-DZ21KU and PT- DS20KU only)
Select [3D SETTINGS] from the main menu, and 
select the item from the sub-menu.
Refer to “Navigating through the menu ” 
(
 page 63) for the operation of the menu screen.
 z After selecting the item, press 
▲▼◀▶ to set.
[3D SYSTEM SETTING]
Set a picture display method for use during 3D signal 
input as necessary for the 3D system in use.
1) Press 
▲▼ to select [3D SYSTEM 
SETTING].
2)
 
Press  ◀▶ to switch [3D SYSTEM 
SETTING].
▶z The setting will change as follows each time 
you press the button.
[SINGLE][DUAL (LEFT)][DUAL (RIGHT)]
[SINGLE] During 3D signal input, sequential 
frames of images for the right eye 
and images for the left eye are
alternately displayed.
[DUAL 
(LEFT)] Only images for the left eye are 
displayed during 3D signal input.
[DUAL 
(RIGHT)] Only images for the right eye are 
displayed during 3D signal input.
Note
 z When 2D images are input, 2D images are 
displayed regardless of [3D SYSTEM SETTING] 
settings.
[3D SYNC SETTING]
Set the way in which the  
terminal and the  terminal will be 
used.
Attention
 z Before connecting the external device with the 
cables to the  terminal and 
the  terminal, finish the [3D 
S

YNC MODE] setting and confirm that the device is 
turned off.
 z Changing [3D SYNC MODE] while connecting the 
c

ables may result in malfunctions of the projector or 
external devices connected.
1) Press  ▲▼ to select [3D SYNC 
SETTING].
2)
 
Press the  button.
▶z The precaution message related to 3D SYNC 
setting is displayed.
3) Press the  button.
▶zThe  [3D SYNC SETTING] screen is displayed.
4) Press 
▲▼ to select [3D SYNC MODE].
5)  
Press  ◀▶ to switch [3D SYNC MODE].
▶z
The setting will change as follows each time 
you press the button.
[OFF][1]
[11]
[2]
[10] [3]
[9][4]
[8][5]
[7][6]
▶zItems set in [3D SYNC1]
[OFF]
Not used.
[1] 3D trigger output
[2] 3D trigger output
[3] Stereo synch input
[4] Stereo synch input
[5] Stereo synch input
[6] Frame synch input
[7] Frame synch input
[8] Frame synch input
[9] 3D trigger output
[10] Stereo synch output
[11] 3D IR TRANSMITTER (+) output 
						

							[3D SETTINGS] menu (PT-DZ21KU and PT- DS20KU only)
86 - ENGLISH
Settings
▶zItems set in [3D SYNC2]
[OFF]
Not used.
[1] Stereo synch output
[2] 3D trigger output
[3] Through 3D SYNC1
[4] Stereo synch output
[5] 3D trigger output
[6] Through 3D SYNC1
[7] Stereo synch output
[8] 3D trigger output
[9] Frame synch output
[10] Frame synch output
[11] 3D IR TRANSMITTER (–) output
6) If you selected [1], [4], [7], or [10], 
press 
▲▼ to select [STEREO SYNC 
OUTPUT DELA
Y] and press ◀▶ to set 
the amount of delay output.
▶z Values in the following range change by units of 
10 us.
0 us to 25 000 us
▶z T

o synchronize multiple projectors to display 3D 
images, use a frame synch input and output.
Select [9] or [10] for the first projector.
Select [6], [7], or [8] for the second and 
subsequent projectors.
▶z Stereo synch is a Duty 50% signal at High 
during Left and at Low during Right.
▶zAn “H” is output to the 3D images display and 
an “L” is output to the 2D image display from 
the terminal for which 3D trigger output is 
selected.
Note
 z [1

1] of [3D SYNC MODE] is the setting when the 
3D IR TRANSMITTER TY-3DTRW (Panasonic) is 
used with this projector. As for connecting method, 
consult your dealer.
[3D SIMUL INPUT SETTING]
Set to input and use simultaneous 3D images signals.
1) Press  ▲▼ to select [3D SIMUL
 INPUT 
SETTING].
2)
 
Press the  button.
▶z The  [3D SIMUL INPUT SETTING]
 screen is 
displayed.
3) Press  ▲▼ to select [LEFT
:RGB1 
RIGHT:RGB2], [LEFT:HDMI 
RIGHT:DVI-D], or [LEFT:SDI1 
RIGHT:SDI2].
4)
 
Press  ◀▶ to switch the setting.
▶z
The setting will change as follows each time 
you press the button.
[OFF][AUTO]
[OFF]
Cannot use 3D simultaneous.
[AUTO] Displays simultaneous 3D images.
Note
 z When set to [AUT

O], 3D images are displayed 
when the same 3D compatible signals are entered 
to each input. However, the P IN P status during P 
IN P is maintained.
 z When [BACKUP

 INPUT MODE] is set to [ON], [1], 
or [2], [3D SIMUL INPUT SETTING] cannot be set.
 z This may not function properly for some external 
devices that are connected.
 zCertain signals may not function properly

. 
						

							[3D SETTINGS] menu (PT-DZ21KU and PT- DS20KU only)
ENGLISH - 87
Settings
[3D INPUT FORMAT]
Set the 3D format for the image signals being input. 
Set a 3D format that matches the input signal.
1) Press 
▲▼ to select [3D INPUT 
FORMA T].
2)
 
Press the  button.
▶z The  [3D INPUT FORMAT] screen is displayed.
3) Press 
▲▼ to select a 3D format.
4)  
Press the  button.
[AUTO]*1Automatically detects 3D format of 
input image signals and displays 
images.
[NATIVE] Forcibly displays images in 2D 
regardless of input image signals.
[SIMULTANEOUS]*2Forcibly displays 3D images in 
simultaneous format regardless of 
input image signals.
[SIDE BY  SIDE] Forcibly displays 3D images in side 
by side format regardless of input 
image signals.
[TOP AND  BOTTOM] Forcibly displays 3D images in top 
and bottom format regardless of 
input image signals.
[LINE BY  LINE]
*3
Forcibly displays 3D images in line 
by line format regardless of input 
image signals.
[FRAME 
SEQUENTIAL]*4
Forcibly displays 3D images in frame 
sequential format regardless of input 
image signals.
*1: During DVI-D or HDMI input only
*2:  During 3G-SDI level B input only
*3:
 
During signals other than interlaced signals are input
*4:

 
During RGB1, RGB2, DVI-D, and HDMI input only
Note
 zWhen set to [AUT

O], [SIMULTANEOUS], [SIDE BY 
SIDE], [TOP AND BOTTOM], [LINE BY LINE], or 
[FRAME SEQUENTIAL], images are not displayed 
in 3D as per the [3D SIMUL INPUT SETTING]. 
However, this only occurs in [AUTO] when 3D 
format can be recognized.
 z This may not function properly for some external 
devices that are connected.
[LEFT/RIGHT SWAP]
Flips the timing of the switch between the left and 
right of an image to display. Change the setting if the 
3D images you see appear strange.
1) Press 
▲▼ to select [LEFT/RIGHT 
SW AP].
2)
 
Press  ◀▶ to switch [LEFT/RIGHT 
SW

AP].
▶zThe setting will change as follows each time 
you press the button.
[NORMAL][SWAPPED]
[NORMAL] If the 3D images are displayed 
correctly, do not change the 
[NORMAL] settings.
[SWAPPED] Select when left and right 3D 
images are swapped to be 
displayed.
Note
 z This is disabled when [3D SYSTEM SETTING] is 
set to any setting other than [SINGLE].
[3D COLOR MATCHING]
Switches the color matching correction data applied to 
the displayed image.
1) Press 
▲▼ to select [3D COLOR 
MA TCHING].
2)
 
Press  ◀▶ to switch [3D COLOR 
MA

TCHING].
▶zThe setting will change as follows each time 
you press the button.
[SHARED 2D/3D][SEPARATE 2D/3D]
[SHARED 
2D/3D] 2D signals and 3D signals use the 
same correction data.
[SEPARATE  2D/3D] 2D signals and 3D signals use 
different correction data.
Note
 z Keep the signal you want to adjust input when you 
s

witch the [COLOR MATCHING] (
 page 91) setting. 
						

							[3D SETTINGS] menu (PT-DZ21KU and PT- DS20KU only)
88 - ENGLISH
Settings
[3D PICTURE BALANCE]
Correct a shift when the brightness or color differ in 
the right eye and left eye images.
1) Press 
▲▼ to select [3D PICTURE 
BALANCE].
2)
 
Press the  button.
▶z The  [3D PICTURE BALANCE]
 screen is 
displayed.
3) Press  ▲▼ to select an item, and press 
◀▶  to adjust the setting.
▶z
Correct the setting value parts of the right eye 
image based on the left eye image.
[CONTRAST] You can adjust the contrast of the 
colors.
[WHITE 
BALANCE HIGH  RED] Adjusts the high red white 
balance.
[WHITE 
BALANCE HIGH  GREEN] Adjusts the high green white 
balance.
[WHITE 
BALANCE HIGH  BLUE] Adjusts the high blue white 
balance.
[BRIGHTNESS] You can adjust the dark (black) 
part of the projected image.
[WHITE 
BALANCE LOW  RED] Adjusts the low red white balance.
[WHITE 
BALANCE LOW  GREEN] Adjusts the low green white 
balance.
[WHITE 
BALANCE LOW  BLUE] Adjusts the low blue white 
balance.
[COLOR] You can adjust the color saturation 
of the projected image.
[TINT] You can adjust the skin tone in the 
projected image.
[CLOCK  PHASE] Adjust when the screen flickers or 
outline blurs.
Note
 z [CLOCK PHASE] settings go are enabled at 
simultaneous input of RGB1 and RGB2 to adjust 
the right eye image.
 zThis is disabled when [3D SYSTEM SETTING] is 
set to any setting other than [SINGLE].
 zThis is disabled when [3D 

TEST PATTERN] is 
displayed.
 z This is disabled when [3D 

TEST MODE] is set to 
any setting other than [NORMAL] and [SIDE BY 
SIDE].
▶■ To display [3D WAVEFORM 
MONITOR]
The left eye and right eye images are divided and 
displayed in a waveform on the left and right.
4) Select [3D W AVEFORM MONITOR] in 
Step 3).
5)
 
Press  ◀▶ to switch [3D W

AVEFORM 
MONITOR].
▶z The setting will change as follows each time 
you press the button.
[OFF][ON]
[OFF] The 3D waveform monitor is not 
displayed.
[ON] The 3D waveform monitor is 
displayed.
Note
 z The 3D waveform monitor is displayed only when 
the [3D PICTURE BALANCE] screen is displayed.
 zThe normal waveform monitor cannot be displayed 
in 3D images.
[DARK TIME SETTING]
Set the black display period to be displayed between 
the right eye image and the left eye image as 
necessary for the 3D system used.
1) Press 
▲▼ to select [DARK TIME 
SETTING].
2)
 
Press  ◀▶ to switch [DARK TIME 
SETTING].
▶z The setting will change as follows each time 
you press the button.
[0.5 ms][1.0 ms][1.5 ms]
[2.7 ms][2.5 ms][2.0 ms]
Note
 z This is disabled when [3D SYSTEM SETTING] is 
set to any setting other than [SINGLE].
 zWhen the setting does not correspond to the 3D 
system in use, phenomenon such as increased 
crosstalk and darkening of displayed images may 
occur

. 
						

							[3D SETTINGS] menu (PT-DZ21KU and PT- DS20KU only)
ENGLISH - 89
Settings
[3D FRAME DELAY]
Adjust the timing of the left-right switch of an image.
1) Press 
▲▼ to select [3D FRAME 
DELA Y].
2)
 
Press  ◀▶ to switch [3D FRAME 
DELA

Y].
▶zValues in the following range change by units of 
10 us.
0 us to 25 000 us
[3D TEST MODE]
Set the image display format for use with 3D system 
adjustments.
1) Press  ▲▼ to select [3D TEST MODE].
2)  
Press  ◀▶ to switch [3D TEST MODE].
▶z
The setting will change as follows each time 
you press the button.
[NORMAL][SIDE BY 
SIDE][LEFT/LEFT]
[BLACK/RIGHT][LEFT/
BLACK][RIGHT/ RIGHT]
[NORMAL] Standard setting.
[SIDE BY SIDE] The left eye image is displayed 
on the left, next to the right eye 
image displayed on the right.
[LEFT/LEFT] Both the left eye image and right 
eye image display the left eye 
input signal.
[RIGHT/RIGHT] Both the left eye image and right 
eye image display the right eye 
input signal.
[LEFT/BLACK] The left eye input signal is 
displayed in the left eye image 
and a completely black image is 
displayed in the right eye image.
[BLACK/RIGHT] A completely black image is 
displayed in the left eye image 
and the right input signal is 
displayed in the right eye image.
Note
 z The [3D 

TEST MODE] settings return to [NORMAL] 
when the projector is switched off.
 z This is disabled when [3D SYSTEM SETTING] is 
set to any setting other than [SINGLE].
 zThis is disabled when [3D 

TEST PATTERN] is 
displayed.
[3D TEST PATTERN]
The 3D test pattern can be used to check operation 
and make adjustments even without a 3D signal.
1) Press  ▲▼ to select [3D TEST 
P ATTERN].
2)
 
Press  ◀▶ to switch [3D TEST 
P

ATTERN].
▶zThe setting will change as follows each time 
you press the button.
Menu screen
+
Entry screenMenu screen +
Left: white/
Right: blackMenu screen +
Left: black/
Right: white
Note
 z The 3D test pattern cannot be displayed when the 
following inputs are selected.
–

▶
VIDEO input
–

▶
RGB1 input (only when [RGB IN] is set to [Y/C])
 zThis is disabled when [3D SYSTEM SETTING] is 
set to any setting other than [SINGLE]. 
						

							[3D SETTINGS] menu (PT-DZ21KU and PT- DS20KU only)
90 - ENGLISH
Settings
[SAFETY PRECAUTIONS 
MESSAGE]
Set to show or hide safety precaution messages 
related to 3D viewing when the projector is switched 
on.
1) Press 
▲▼ to select [SAFETY
 
PRECAUTIONS MESSAGE].
2)
 
Press  ◀▶ to switch [SAFETY

 
PRECAUTIONS MESSAGE].
▶z The setting will change as follows each time 
you press the button.
[ON][OFF]
[ON] Shows safety precaution 
messages related to 3D viewing 
when the projector is switched on.
[OFF] Hides safety precaution messages 
related to 3D viewing when the 
projector is switched on.
Note
 z Set to [OFF] to hide the safety precautions 
message when the projector is switched on.
 zA

 confirmation window is displayed when switched 
from [ON] to [OFF]. Select [OK] in the confirmation 
window and press the  button to change 
the setting to [OFF].
Attention
 z When 3D images are viewed by unspecified 
number of people for commercial use, display 
safety precaution messages related to 3D viewing 
to notify viewers.
[3D SAFETY PRECAUTIONS]
Show safety precaution messages related to 3D 
viewing.
1) Press 
▲▼ to select [3D SAFETY
 
PRECAUTIONS].
2)
 
Press the  button.
▶z The [3D SAFETY  PRECAUTIONS] screen is 
displayed.
▶z Press 
◀▶ to turn the page.
1/2
MENU
3D SAFETY PRECAUTIONS
I\f you \biew 3D image\Ns, please note below\N.
In addition, when 3D\N images will be \bie\Nwed
by unspeci\fied numbe\Nr o\f people
or used \for commercia\Nl applications,
someone in authority\N should con\bey
the \following precau\Ntions.
To enjoy 3D images s\Na\fely and com\fortabl\Ny,
please re\fer to the\N Operating Instruct\Nions
\for in-depth descri\Nption.
CHANGE
EXIT
2/2
MENU
3D SAFETY PRECAUTIONSPl\fas\f r\f\brain \brom vi\fw\ling 3D imag\fs
i\b you do not \b\f\fl w\fll\l or ar\f \fxp\fri\fncing
visual \batigu\f.
Pl\fas\f us\f th\f cont\fnt\ls which has b\f\fn
prop\frly mad\f \bor 3D.
Vi\fw \brom at l\fast th\f \lr\fcomm\fnd\fd distanc\f.\l
(3 tim\fs th\f \f\b\b\fctiv\f\l h\fight o\b th\f scr\f\fn)\l
R\f\b\fr to th\f Op\frating\l Instructions
i\b this m\fssag\f is no \llong\fr n\f\fd\fd.
CHANGE
EXIT