Panasonic Projector Pt D12000u Operating Instructions

ENGLISH – 31
Getting Started
Procedure of installation  „
Disconnect the power before installing the input module.
Slot Cover
MAIN POWER AC INOFF ON
IN OUTRS-232C IN RS-422 IN RS-422 OUTSERIALLAN
REMOTE 1 REMOTE 2 IN
OUTIN
SYNC/HD VDB/PBG/Y R/PRS-VIDEO INVIDEO RGB 2 INDVI-D IN
RGB 1 INAUXDVI-DRGB2RGB1S-VIDEOVIDEOAUTO
SETUPMENU LENS
SHUTTER
LIGHT POWER ON STANDBY
ON
OFF ENTER
Remove the slot cover. 1. 
Remove 2 screws.
Insert the input module. 2. 
Slot
Input module
Install the two screws. 3. 
Register the...

32 – ENGLISH
Installation of (optional) input modules (continued)
Connecting signals to the input module
When installing the projector, it is necessary to connect signals to the input module in accordance with the 
connecting equipment.
Refer to the following diagram to establish proper signal connection.
MAIN POWER AC INOFF ON
IN OUTRS-232C IN RS-422 IN RS-422 OUTSERIALLAN
REMOTE 1 REMOTE 2 IN
OUTINSYNC/HD VDB/PBG/Y R/PRS-VIDEO INVIDEO RGB 2 INDVI-D IN
RGB 1 INAUXDVI-DRGB2RGB1S-VIDEOVIDEOAUTO
SETUPMENU...

ENGLISH – 33
Getting Started
Connecting the signal to the  SD-SDI input module
SD-SDI Module
ET-MD77SD1IN
SERIALOUT
LAN
SD-SDI input module (optional)
ET-MD77SD1 (for 480i/576i)
SD-SDI signal SD-SDI signal output
(active through)LAN terminal
*1
(10BASE-T/100BASE-TX)
Professional 
Digital VCR
Note
If a source with an unstable signal is connected, errors in automatic signal recognition may occur. If this  • 
happens, use the SYSTEM SELECTOR menu to switch the format to the one which matches the signals...

34 – ENGLISH
Installation of (optional) input modules (continued)
Connecting the signal to the dual link HD/SD-SDI input 
module
Dual Link
HD-SDI
Module
ET-MD100SD4LINK-A
SERIAL INLINK-B
Dual link HD/SD-SDI input module (optional)
ET-MD100SD4
HD-SDI or 
SD-SDI signal
Professional 
Digital VCR
When connecting a single link signal, connect to the LINK-A terminal. • 
When connecting a dual link signal, connect to both the LINK-A and LINK-B terminals. • 
Note
You can switch the input format mode from the...

ENGLISH – 35
Getting Started
Connecting signals to the  DVI-D input module
DVI Module
ET-MD77DVDVI-D IN LAN
DVI-D input module (optional)
ET-MD77DV
DVI-D signal LAN terminal
*1
(10BASE-T/100BASE-TX)
DVD player or high-vision 
video deck equipped with 
DVD/HDMI terminal PC with DVI output
Pin assignments and signal names of DVI-D input  • 
terminal are listed in the table at right. Pin 
No.SignalPin 
No.Signal
1
T.M.D.S data 2–m18
9p
qx
Outside view2
T.M.D.S data 2+n
+5V
3T.M.D.S data 2 / 4 
shieldo...

36 – ENGLISH
 
How to install and remove the projection lens (optional)
Adjust the lens shift position so that it is at the home 
position (p. 41) before installing or removing the 
projection lens.
Attention
Remove the dust-proof sponge from the lens fitting  • 
of the projector before installing the projection lens. 
(Keep the dust-proof sponge in a safe place for 
later use if needed.)
After removing the projection lens, install the dust- • 
proof sponge to the lens fitting of the projector in 
order...

ENGLISH – 37
Basic Operation
Projection
 
Power indicator lamp
This shows the power supply status. Make sure 
that you fully understand the operation of the power 
indicator lamp before operating the projector.
Indicator 
statusProjector status
Off Main power is off
Red LitStandby mode
POWER ON ( | ) button can be pressed 
so that images can be projected.
Green Lit Images are being projected (on)
Orange LitCooling mode
After a short while, the projector will 
switch to standby mode.
Attention
While the...

38 – ENGLISH
Projection (continued)
 
Powering up the projector
1
  Connect the supplied power 
cable. (120 V/240 V, 50 Hz/60 Hz)
2
  Press the “ | ” marked side of the 
MAIN POWER switch to turn on 
the power.
The power indicator lamp on the projector will  • 
flash in red. After a short period, the indicator 
will illuminate and the projector will enter 
standby mode.
3
  Press POWER ON “ | ”.
The power indicator lamp illuminates in green  • 
and soon the image is projected on the screen.
Note
If the...

ENGLISH – 39
Basic Operation
 
Powering off the projector
1
  Press POWER STANDBY “”.
A confirmation screen will appear. • 
ENTER
POWER OFF
 CHANGE
 EXECUTE
OKCANCEL
2
 Press ◄ or ► to select “OK” and 
press ENTER.
(or press POWER STANDBY “
” 
again.)
The projection of the image stops, and the  • 
power indicator lamp of the main unit lights up 
orange. (The cooling fan keeps running.)
3
  Wait until the power indicator 
lamp of the main unit turns to 
red (i.e., until the cooling fan 
stops). (Approx. 3...

40 – ENGLISH
 
How to adjust the lens
How to adjust the focus, zoom and shift
Use the Lens Shift, Zoom, and Focus controls to properly frame the image on the screen.
LENS
FOCUS
 ADJUST
LENS
ZOOM
 ADJUST
LENS
SHIFT
 ADJUST
At the projector  „
Press LENS on the control panel. 1. 
Pressing the button changes the setup  • 
screen in the order of “FOCUS”, “ZOOM” and 
“SHIFT”.
Press ▲▼◄► to select an item  2. 
and adjust it.
LENS
FOCUS
 ADJUSTUsing the remote control  „
Press LENS (FOCUS, ZOOM,  1. 
SHIFT) on...