Panasonic Projector Pt Ae8000EH Operating Instructions

[POSITION] menu
ENGLISH - 61
Settings
[ASPECT]
You can switch the image aspect ratio manually when 
needed. 
Aspect ratio depends on signals.
Switch settingsSwitch settings
 
■ When a VIDEO/S-VIDEO signal is input
[NTSC/NTSC4.43/PAL-M/PAL60 input]
[AUTO][4:3][16:9]
[ZOOM][JUST][S16:9]
Note
 
z [AUTO] is enabled only when an NTSC signal is input for 
both VIDEO and S-VIDEO signals. 
[PAL/PAL-N/SECAM input]
[16:9][S16:9][14:9][ZOOM1]
  
   
[4:3][JUST][ZOOM2]
 
■ When a COMPUTER (RGB) signal is 
input...

[POSITION] menu
62 - ENGLISH
Settings
AspectScreen
[4:3]
Projects at 4:3. Input signal
 
Projection screen
[16:9]
Projects at 16:9. 
(Enlarged horizontally)Input signal
 
Projection screen
[S16:9]
Projects a 16:9 aspect 
video onto a 4:3 aspect 
screen. Input signal
 
Projection screen
[JUST]
Adjusts horizontally to 
fit 16:9. 
When projecting 
a 4:3 aspect ratio 
video, distortion in the 
center of the screen is 
reduced.
(Enlarged horizontally)Input signal
 
Projection screen
Aspect
Screen
[ZOOM]...

[POSITION] menu
ENGLISH - 63
Settings
[WSS]
In the European broadcasting system, if the input 
signal contains an identification signal, WSS 
automatically switches the aspect ratio to the required 
setting. (
 page 61)
Switch settingsSwitch settings
[ON]Switch automatically
[OFF] Do not switch automatically
Note
 
z Aspect ratio switches only in the case of these input 
signals: PAL/625i (576i)/625p (576p)
[OVER SCAN]
If the 4 edges of an image are partly dropped, you can 
use this function to adjust...

[3D SETTINGS] menu
64 - ENGLISH
Settings
[3D SETTINGS] menu
Either press the  button on the remote 
control or select [3D SETTINGS] from the 
main menu in “Navigating through the menu” 
(
 page 37) and select the item from a 
submenu.
 
z After selecting an item, adjust the screen position 
using the ▲▼◄ ► buttons.
Remote contro
lProjector controls\
[SCREEN SIZE]
When viewing 3D video, set the screen size for 
projection.
[102 cm (40 inches)][152 cm (60 inches)]
[508 cm (200 inches)]
[203 cm (80...

[3D SETTINGS] menu
ENGLISH - 65
Settings
Note
 
z If a setting other than [AUTO] is selected when the input is switched to HDMI, [3D INPUT FORMAT] is changed to [AUTO] 
when actions such as turning the power of/on, switching input, or switching the signal are performed on the connected 
device. 
See the following table regarding settings, input signals and the image for viewing.
Switching 3D 
format
Input signal [AUTO]
[SIDE BY SIDE] [TOP AND  
BOTTOM] [NATIVE]
FRAME  
PACKING
(Normal 3D video)
SIDE BY...

[3D SETTINGS] menu
66 - ENGLISH
Settings
[LEFT/RIGHT SWAP]
Switch to [SWAPPED] if you feel discomfort when 
watching a 3D video with 3D Eyewear.
Switch settingsSwitch settings
[NORMAL][SWAPPED]
[NORMAL]If the 3D video is being displayed 
correctly while the 3D Eyewear is 
being worn, do not change from 
[NORMAL] settings.
[SWAPPED]
Select this if a feeling of discomfort is 
felt towards the 3D video while wearing 
3D Eyewear.
Note
 
z If 3D video is being correctly displayed in 3D, setting 
[LEFT/RIGHT...

[3D SETTINGS] menu
ENGLISH - 67
Settings
 
■ [3D WAVEFORM MONITOR]
For easy balance adjustment, use a video device that 
supports 3D and displays the video output (brightness) 
level of the 3D video for the left and right eye respectively.
1)  
Press the  button.
 
z The [3D WAVEFORM MONITOR] menu is 
displayed.
3D WA
VEFORM MONI TOR
   OFF
   SINGLE LINE SCA\(N(\f)
   SINGLE LINE SCA\(N(R)
   SINGLE LINE SCA\(N(G )
   SINGLE LINE SCA\(N(B)
MOVE LINE
PICT\bRE
POSITION
LANG\bAGE
3D SETTINGS
LENS CONTROL...

[3D SETTINGS] menu
68 - ENGLISH
Settings
5)  Press the ▲▼◄► buttons to specify the 
location of the required character to enter 
and press the  button.
 
z You can enter up to 16 characters.
 
z Select [ALL DELETE] and press the  
button to erase all input text. If you press the 
 button on the remote control, you 
can erase the character currently selected by 
the cursor in the input box.
6)  
Press the ▲▼◄► buttons to select [OK].
7)   Press the  button.
Note
 
z Press the  button without entering any...

[3D SETTINGS] menu
ENGLISH - 69
Settings
 
● [PICTURE BALANCE MEMORY NAME 
CHANGE]
You can edit the memory name of details saved using 
[PICTURE BALANCE MEMORY SAVE].
1)  
Press the ▲▼ buttons to select [MEMORY 
NAME CHANGE] and press the  
button.
 
z The [PICTURE BALANCE MEMORY NAME 
CHANGE] menu is displayed.
PICTURE BALANCE ME\2MORY 
NAME CHANGE
MEMORY1
MEMORY2
MEMORY\f
PICTURE
POSITION
LANGUAGE
\fD SETTINGS
LENS CONTROL OPTION
2)  Press the ▲▼ buttons to select the 
memory name to be changed and...

[3D SETTINGS] menu
70 - ENGLISH
Settings
[3D EYEWEAR BRIGHTNESS]
This enables adjusting the brightness for the 3D 
Eyewear.
Switch settingsSwitch settings
[LIGHT][DARK]
 
 
[NORMAL]
[LIGHT] Select to brighten the 3D video display.
[NORMAL] Select this as standard for 3D viewing
[DARK] Select to reduce 3D video afterimage.
Note
 
z When you switch the brightness of 3D Eyewear, the 
screen may momentarily appear jumbled.
[3D IR TRANSMITTER]
This controls the 3D IR Transmitter embedded in this 
projector....