Panasonic Projector PT-AE7000U User Manual

[LENS CONTROL] menu
ENGLISH - 71
Settings
[LENS MEMORY NAME CHANGE]
 
■
Press the ▲▼ buttons to select the 
1)  
memory name to be changed.
 LENS MEMORY  NAME CHANGE
LENS MEMORY 1
LENS MEMORY 2
LENS MEMORY 3
LENS MEMORY 4
LENS MEMORY 5
LENS MEMORY 6
PICTURE
POSITION
LANGUAGE
3D SETTINGS
LENS CONTROL OPTION
Press the  button.
2)  
[LENS MEMORY NAME INPUT] screen is 
 
z
displayed.
LENS MEMORY  NAME INPUT
ABCDE FGHIJK LM
NO PQRSTU VWXY Z
ab cdefg hijk lm
nopqr stuvwx yz
123456789 0
!" #$% &'
＊+-/=...

[LENS CONTROL] menu
72 - ENGLISH
Settings
[H-AREA POSITION]
You can move the frame area horizontally, such as 
aligning the right or left frame edge to the screen 
edge.Moving left
Moving right
For example, when projecting an overscanned 16:9 
projection area at a 4:3 aspect ratio on a 4:3 aspect 
screen, you can adjust the horizontal discrepancy 
between the screen position and the video display 
position.
 
16:9 projection area 4:3 screen
4:3 video display position
[V-AREA POSITION]
You can move the...

[OPTION] menu
ENGLISH - 73
Settings
[OPTION] menu
Select [OPTION] from the main menu of 
“Navigating through the menu” (
 page 37), 
and choose an item from the submenu.
Select item and use the ◄ ► buttons to switch the 
 
z
settings.
Remote contro lProjector controls
[ON-SCREEN DISPLAY]
This enables setup related to on-screen display.
Press the  button.
The [ON-SCREEN DISPLAY] menu is displayed.
 
z
 ON-SCREEN DISPLAY
 INPUT  GUIDE
 OSD DESIGN
 OSD POSITION  DETA
ILED
 T YPE1
 CENTER
PICTURE
POSITION...

[OPTION] menu
74 - ENGLISH
Settings
[STARTUP LOGO]
You can switch the Panasonic logo that is displayed 
when starting up the projector on/off. 
Switch settingsSwitch settings
[ON]Active
[OFF] Inactive
Note
The logo Panasonic is displayed for 15 seconds.
 
z
[AUTO SEARCH]
Sets whether to automatically search for terminals 
that have an input signal when the projector is turned 
on. 
Switch settingsSwitch settings
[ON] Active
[OFF] Inactive
Attention
Set this to [ON] under normal circumstances.
 
z
When no...

[OPTION] menu
ENGLISH - 75
Settings
[TRIGGER 1/2 SETTING]
You can set the function for each trigger terminal.
The trigger terminals for this projector are used as 
both the input/output terminal for the trigger function 
and the output terminal for the external 3D IR 
Transmitter (optional accessory). This is selected with 
a menu.Attention
You can connect a maximum of two external 3D IR 
 
z
Transmitter (optional accessory).
Make sure the  switch of the projector 
 
z
is turned  before a cable is...

[OPTION] menu
76 - ENGLISH
Settings
[BLANK]
•   
When [BLANK] is activated, output is 12 V. If the 
setting is released, output is 0 V.
[RS-232C COMMAND LINK]
•   
Receives commands (
 page 98) from external 
device and outputs 12 V.
Input
 
z
[POWER ON/OFF] [BLANK]
[POWER ON/OFF]
•   
If the trigger input signal from the external device is 
changed from 0 V to 12 V, the projector power will be 
switched on. And if it is changed from 12 V to 0 V, the 
power will be switched off.
[BLANK]
•   
If the...

[OPTION] menu
ENGLISH - 77
Settings
[LAMP POWER]
Switch the lamp intensity according to the usage 
environment of the projector and its intended use.
Switch settingsSwitch settings
[NORMAL]When higher luminance is 
required
[ECO] When lower luminance is 
sufficient
Note
The brightness in the [ECO] settings is lowered 
 
z
enabling saving power and reducing operating noise. It 
is recommended that you use the [ECO] setting when 
viewing in a place where natural light is blocked and 
there is no artificial...

[OPTION] menu
78 - ENGLISH
Settings
[
 
■ POWER ON LINK]
Specify whether or not to switch the power of the projector 
on when it is in standby by operating external devices.
Switch settingsSwitch settings
[NO]
Inactive
[YES] Switch projector power on along 
with external devices
Note
Depending on the external device, the projector may 
 
z
automatically turn on when some functions of the 
connected devices are used. (Only in standby)
Due to the projector’s characteristics, it takes time 
 
z
before...

[OPTION] menu
ENGLISH - 79
Settings
[OTHER FUNCTIONS]
Press the  button.
The [OTHER FUNCTIONS] menu is displayed.
 
z
 OTHER FUNCTIONS
 FREEZE
 BLANK
 VIERA  LINK
PICTURE
POSITION
LANGUAGE
3D SETTINGS
LENS CONTROL OPTION
 
■ [FREEZE]
You can temporarily freeze the projected video 
independently of external device playback.
Press the  button.
Pressing the  button cancels the 
 
z
function.
Note
While displaying the frozen image, you can enter the 
 
z
[AREA SELECT] mode of the [SPLIT ADJUST] menu 
by...

TEMP and LAMP Indicators 
80 - ENGLISH
Maintenance
TEMP and LAMP Indicators
Managing the indicated problems
If a problem should occur with the projector, the lamp indicator  and/or temperature indicator  
will illuminate or flash. Check the indicator status and deal with problems as follows.Attention
When switching off power to deal with problems, ensure that you follow the procedure in “Switching off the power”. 
 
z
(
 page 30)
Note
Check the status of the power supply with the power indicator . (...