Panasonic Network Interface Unit Wj Nt314 Operating Instructions

41
Auto mode
It is possible to activate auto mode for the camera con-
nected to the video input connector of event CH (CH1 to
4) when the AVMD is detected. (When a preset position
number is selected, operation starts after the camera
moves to the preset position.)
Auto track: Performs auto track when the camera sup-
ports auto track (AUTO TRACK).
–:OFF
Default setting:– 
[Terminal alarm 1 to 4]
Select ON or OFF to determine whether or not to
receive Terminal alarm 1 to 4 (input to the connector
terminal...

42
Configure the settings relating to the alarm image [Alarm image setup]
Click the [Alarm] tab on the Alarm setup page. (page 40)
The settings relating to the alarm image to be transmitted to the FTP server can be configured on this page. The
alarm image will be transmitted to the FTP server. To transmit alarm images to the FTP server, it is necessary to
configure the settings in advance. (page 49)
Refer to pages 40 and 43 for further information about the settings relating to the alarm action and the...

43
Alarm output terminal setup
Select a desired alarm output terminal number from the
pull-down menu, and configure the following items. 
[Alarm output setup]
Select ON or OFF to determine whether or not to
output the alarm signals to the alarm out connector
when an alarm is detected. 
Default setting: OFF
[External terminal output setup]
Select Latch or Pulse for the alarm output terminal at
an alarm occurrence.
Latch:When an alarm is detected, alarm output con-
nector will be in the state selected for...

44
Configure the settings relating to the mail notification [Notification]
Click the [Notification] tab on the Alarm setup page. (page 40)
The settings relating to the alarm mail can be configured on this page. To notify of an alarm occurrence by e-mail, it
is necessary to configure the settings of the mail server. (page 48)
E-mail notification setup
[To E-mail server setup]
When To E-mail server setup is clicked, the [Mail] tab
of the Server setup page will be displayed. (page
48)
[E-mail...

45
Configure the settings relating to Panasonic alarm protocol [Panasonic alarm
protocol]
Click the [Notification] tab on the Alarm setup page. (page 40)
The settings relating to Panasonic alarm protocol can be configured on this page. 
Panasonic alarm protocol setup
[Panasonic alarm protocol]
Select ON or OFF to determine whether or not to
notify of an alarm occurrence by Panasonic alarm proto-
col when an alarm is detected. 
Default setting: OFF
Note: 
When ON is selected, the alarm occurrence will...

46
[User authentication]
Select ON or OFF to determine whether or not to
authenticate the user. 
Default setting: OFF
[User name]
Enter a user name. 
Number of characters that can be entered:1 - 32
characters
Default setting:(blank)
[Password] [Retype password]
Enter the password. 
Number of characters that can be entered:4 - 32
characters
Default setting:(blank)
Note:
When the user name already in use is entered and
the [SET] button is clicked, the respective user infor-
mation will be overwritten. 
For...

47
[Host authentication]
Select ON or OFF to determine whether or not to
authenticate the host. 
Default setting: OFF
Important: 
Before selecting ON for Host authentication, it is
necessary to register IP addresses of the PCs to be
allowed to access the unit and determine their
access levels.
[IP address]
Enter the IP address of the PC to be allowed to access
the unit.
Host name is unavailable for the IP address.
Default setting:(blank)
Notes: 
•When IP address/subnet mask is entered, it is pos-
sible...

48
Configure the settings of the servers [Server setup]
The settings relating to the mail server and the FTP server can be configured on this page. 
The Server setup page has 2 tabs of the [Mail] tab and the [FTP] tab. 
Configure the settings relating to the mail server [Mail]
Click the [Mail] tab on the Server setup page.
The settings relating to the mail server used to send the alarm mail can be configured on this page. 
[SMTP server address]*
Enter the IP address or the host name of the SMTP
server...

49
Configure the settings relating to the FTP server [FTP]
Click the [FTP] tab on the Server setup page. (page 48)
The settings relating to the FTP server used to transmit the alarm images can be configured on this page. 
[FTP server address]
Enter the IP address or the host name of the FTP serv-
er. 
Number of characters that can be entered:1 - 128
characters
Default setting:(blank)
Important: 
When entering the host name for FTP server
address, it is necessary to configure the DNS set-
tings on the...

50
Configuring the network settings [Network setup]
The network settings and the settings relating to DDNS (Dynamic DNS) and SNMP (Simple Network management
Protocol) can be configured on this page. 
The Network setup page has 4 tabs of the [Network] tab, the [DDNS] tab, the [SNMP] tab and the [FTP] tab. 
Configure the network settings [Network]
Click the [Network] tab on the Network setup page.
The following information is required to configure the network settings. 
Contact the network administrator or...