Panasonic Network Camera Wv Sw158 Installation Guide

21
Using a one-gang junction box
  •  Secure the mount bracket (accessory) to the one-gang junction box built in a ceiling or a wall.
Note:
 • Ceiling installation:
    The mount bracket shall be mounted with aligning the front side (the lens side) of the camera 
with the position of the arrow in 
.
   •  Wall installation:
    The mount bracket shall be mounted with 
 facing upward.
83.5 mm {3-9/32"}
One-gang junction box
Mount bracket (accessory)
[Mounting hole pattern] 

22
IMPORTANT:
  •  When inserting an SD memory card, make sure the direction.
  • Before removing the SD memory card, select Not use for SD memory card on the [SD 
memory card] tab of the setup menu first. (
 Operating Instructions (included in the CD-ROM))
  Remove the enclosure. ( Page 16)
  Insert an SD memory card fully into the SD 
memory card slot until a click is heard. 
  Attach the enclosure to the camera. 
 (
 Page 31)
  When removing the SD memory card from the 
SD memory card slot,...

23
Caution:
  •  FOR UL LISTED MODEL(S), ONLY CONNECT PoE 48 V CLASS 2 POWER SUPPLY (UL 
1310/CSA 223) or LIMITED POWER SOURCE (IEC/EN/UL/CSA 60950-1).
Before starting the connection, turn off the power of the devices to be connected.
Check and prepare the required devices and cables for connection.
Note:
  •  Refer to pages 26 and 27 when using the mount bracket (accessory). 
  •  Refer to pages 26 and 27 when using the conduit.
Connect a LAN cable (category 5 or better, straight) between a PoE device...

24
Waterproof treatment for the cable joint sections
Adequate waterproof treatment is required for the cables when installing the camera outdoors. The 
camera body is waterproof, but the cable ends are not waterproof.
Be sure to use the supplied waterproof tape at the points where the cables are connected to apply 
waterproof treatment in the following procedure. Failure to observe this or use of a tape other than 
the provided waterproof tape (such as a vinyl tape) may cause water leakage resulting in...

25
Connection example

LAN cable (category 5 or better, straight)
IMPORTANT: 
  •  Use a switching hub which is compliant with 10BASE-T/100BASE-TX. 
PoE device (hub)
LAN cable
(category 5 or better, straight)
LAN cable
(category 5 or better, straight)LAN cablePC
(category 5 or better, straight) 

26
Camera mounting

 Remove the enclosure. (3 screws) ( Page 16)
 Connect the cables to the camera. ( Pages 23 and 24) 
  • Waterproof the connecting portion. (
 Page 24) 
  Secure the camera with 3 screws (M4) (locally procured).
IMPORTANT: 
  •  Do not touch the lens. 
  •  When tightening the screws, be careful to ensure that the cables does not tangle the cables.

 Connect each cable.
    • Apply waterproof treatment to all connections. (
 Page 24)
 Connect the conduit attachment (locally...

27
 
 Connect each cable.
    • Apply waterproof treatment to all connections. (
 Page 24)
 Secure the mount bracket to the one-gang junction box. (2 screws (M4) (locally procured))
  Secure the camera to the mount bracket with 3 fixing screws (accessory).
    (Recommended tightening torque: 1.4 N·m {1 lbf·ft})
Camera
Attachment for female thread
Conduit attachment
Mount bracket Fixing screws
Conduit
Network cable
Camera
Mount bracket
One-gang junction box
Network cable
Fixing screws
O
CeilingO
Wall 

28
Using the side cable access hole 
  When installing the camera directly on the ceiling or wall with cables exposed, cut off a portion of 
the mount bracket to open a cable access hole. 
Cut off 

29
 Adjust the camera angle.
When determining the camera angle, repeat fine adjustments by gradually moving the panning 
table and tilting table.
  •  Attach the lens adjuster (accessory) to the lens and adjust the direction of the lens. Attach the 
wider end of the lens adjuster to the lens.
  •  Do not touch the lens with your hand when making adjustments.
  •  Make adjustments to the direction of the lens while confirming the picture displayed on com-
puter’s monitor.
  •  When adjusting the...

30
Note:
  •  Depending on the vertical/horizontal angle used, the edges of the camera may be projected.
  •  Use Extra Zoom when you want to adjust the angular field of view on the Tele side. 
  •  If the 3x extra zoom is applied when 2048×1536, 1920×1080, 1280×960, 1280×720 is select-
ed for the image capture size, the image quality will be deteriorated because the effect of Extra 
Zoom is not provided.
 
Attach the lens adjuster (accessory), and rotate the lens to adjust the focus of the lens.
  •...