Panasonic Network Camera Wv Sw158 Installation Guide

							21
Using a one-gang junction box
  •  Secure the mount bracket (accessory) to the one-gang junction box built in a ceiling or a wall.
Note:
 • Ceiling installation:
    The mount bracket shall be mounted with aligning the front side (the lens side) of the camera 
with the position of the arrow in 
.
   •  Wall installation:
    The mount bracket shall be mounted with 
 facing upward.
83.5 mm {3-9/32"}
One-gang junction box
Mount bracket (accessory)
[Mounting hole pattern] 
						

							22
IMPORTANT:
  •  When inserting an SD memory card, make sure the direction.
  • Before removing the SD memory card, select Not use for SD memory card on the [SD 
memory card] tab of the setup menu first. (
 Operating Instructions (included in the CD-ROM))
  Remove the enclosure. ( Page 16)
  Insert an SD memory card fully into the SD 
memory card slot until a click is heard. 
  Attach the enclosure to the camera. 
 (
 Page 31)
  When removing the SD memory card from the 
SD memory card slot, remove the enclosure  
(
 page 16), and push the card until a click is 
heard. After the SD memory card is removed, 
attach the enclosure to the camera again. 
(
 Page 31)
Insert/remove an SD memory card
Label side 
						

							23
Caution:
  •  FOR UL LISTED MODEL(S), ONLY CONNECT PoE 48 V CLASS 2 POWER SUPPLY (UL 
1310/CSA 223) or LIMITED POWER SOURCE (IEC/EN/UL/CSA 60950-1).
Before starting the connection, turn off the power of the devices to be connected.
Check and prepare the required devices and cables for connection.
Note:
  •  Refer to pages 26 and 27 when using the mount bracket (accessory). 
  •  Refer to pages 26 and 27 when using the conduit.
Connect a LAN cable (category 5 or better, straight) between a PoE device (such as a hub) and the 
network connector of the camera.
Connect a LAN cable (category 5 or better, straight, STP) between a PoE device (such as a hub) 
and the network connector of the camera.
IMPORTANT:
  •  Use all 4 pairs (8 pins) of the LAN cable. 
  •  The maximum cable length is 100 m {328 feet}.
  •  Make sure that the PoE device in use is compliant with IEEE802.3af standard. 
  •  When the LAN cable is disconnected once, reconnect the cable after about 2 seconds. When 
the cable is quickly reconnected, the power may not be supplied from the PoE device.
Connection
Network cable
RJ-45 (female) 
						

							24
Waterproof treatment for the cable joint sections
Adequate waterproof treatment is required for the cables when installing the camera outdoors. The 
camera body is waterproof, but the cable ends are not waterproof.
Be sure to use the supplied waterproof tape at the points where the cables are connected to apply 
waterproof treatment in the following procedure. Failure to observe this or use of a tape other than 
the provided waterproof tape (such as a vinyl tape) may cause water leakage resulting in malfunc-
tion.
LAN cable
Note:
  How to wind the supplied waterproof tape
  •  Stretch the tape by approx. twice (see the illustration) 
and wind it around the cable. Insufficient tape stretch 
causes insufficient waterproofing.
  •  Make sure to wind the tape so that it does not press 
down on the hook of the network cable.
  •  To install this product outdoors, be sure to waterproof the cables. 
Waterproof grade (IEC IP66 or equivalent) is applied to this product 
only when it is installed correctly as described in these operating 
instructions and appropriate waterproof treatment is applied. The mount brackets are not 
waterproofed.
Wind the tape in a half-overlapping manner.
Stretch the tape to 
about twice.
2x
hook 
						

							25
Connection example

LAN cable (category 5 or better, straight)
IMPORTANT: 
  •  Use a switching hub which is compliant with 10BASE-T/100BASE-TX. 
PoE device (hub)
LAN cable
(category 5 or better, straight)
LAN cable
(category 5 or better, straight)LAN cablePC
(category 5 or better, straight) 
						

							26
Camera mounting

 Remove the enclosure. (3 screws) ( Page 16)
 Connect the cables to the camera. ( Pages 23 and 24) 
  • Waterproof the connecting portion. (
 Page 24) 
  Secure the camera with 3 screws (M4) (locally procured).
IMPORTANT: 
  •  Do not touch the lens. 
  •  When tightening the screws, be careful to ensure that the cables does not tangle the cables.

 Connect each cable.
    • Apply waterproof treatment to all connections. (
 Page 24)
 Connect the conduit attachment (locally procured) to the conduit.
 Secure the mount bracket to the conduit attachment with the attachment for female thread 
(locally procured).
  Mount the mount bracket to either a ceiling or a wall.
    (3 screws (M4) (locally procured))
  Secure the camera to the mount bracket with 3 fixing screws (accessory).
    (Recommended tightening torque: 1.4 N·m {1 lbf·ft})
Installation
O
CeilingO
Wall 
						

							27
 
 Connect each cable.
    • Apply waterproof treatment to all connections. (
 Page 24)
 Secure the mount bracket to the one-gang junction box. (2 screws (M4) (locally procured))
  Secure the camera to the mount bracket with 3 fixing screws (accessory).
    (Recommended tightening torque: 1.4 N·m {1 lbf·ft})
Camera
Attachment for female thread
Conduit attachment
Mount bracket Fixing screws
Conduit
Network cable
Camera
Mount bracket
One-gang junction box
Network cable
Fixing screws
O
CeilingO
Wall 
						

							28
Using the side cable access hole 
  When installing the camera directly on the ceiling or wall with cables exposed, cut off a portion of 
the mount bracket to open a cable access hole. 
Cut off 
						

							29
 Adjust the camera angle.
When determining the camera angle, repeat fine adjustments by gradually moving the panning 
table and tilting table.
  •  Attach the lens adjuster (accessory) to the lens and adjust the direction of the lens. Attach the 
wider end of the lens adjuster to the lens.
  •  Do not touch the lens with your hand when making adjustments.
  •  Make adjustments to the direction of the lens while confirming the picture displayed on com-
puter’s monitor.
  •  When adjusting the horizontal angle of cameras mounted to a ceiling, adjust the direction of the 
lens by moving the lens holding the indentations on the sides of the lens.
Adjustment
Horizontal position : -20° to +20°
Vertical position : -20° to +90°Vertical position : -90° to +20°
Horizontal position : -80° to +80°
O
CeilingO
Wall 
						

							30
Note:
  •  Depending on the vertical/horizontal angle used, the edges of the camera may be projected.
  •  Use Extra Zoom when you want to adjust the angular field of view on the Tele side. 
  •  If the 3x extra zoom is applied when 2048×1536, 1920×1080, 1280×960, 1280×720 is select-
ed for the image capture size, the image quality will be deteriorated because the effect of Extra 
Zoom is not provided.
 
Attach the lens adjuster (accessory), and rotate the lens to adjust the focus of the lens.
  •  When making adjustments to the focus of the lens, attach the narrower end of the lens adjuster 
to the lens.
When attaching or removing the lens adjuster, 
squeeze the wider end of the lens adjuster as 
shown in the illustration to open the narrower end 
of the lens adjuster.
Note:
 • 
When the focus is difficult to adjust, set the [Zoom] button on the Live page to x2.