Panasonic Network Camera Wv Sw158 Installation Guide

11
Keep SDXC/SDHC/SD memory cards 
(option) away from infants and children. 
Otherwise, they may swallow the cards by mis-
take. In this case, consult a doctor immediately.
Do not hang down from this product or 
use this product as a pedestal.
Failure to observe this may cause a drop 
resulting in accidents.
Correctly perform all wiring
Short circuits in the wiring or incorrect wiring 
may cause fire or electrical shock.
Turn the power off when cleaning this product. 
Failure to observe this may cause...

12
card will be deleted when formatted. If an unfor-
matted SD memory card or an SD memory 
card formatted with other devices is used, this 
product may not work properly or performance 
deterioration may be caused. Refer to the 
Operating Instructions (included in the CD-ROM) 
for how to format a SD memory card. 
  • When some SD memory cards are used 
with this product, the product may not 
work properly or performance deterioration 
may be caused. Use the SD memory cards 
recommended in page 38....

13
Precautions for installation
This product is designed to be installed 
under eaves.
Install the product under eaves to avoid direct 
sunlight.
Installing place
Contact your dealer for assistance if you are 
unsure of an appropriate place in your partic-
ular environment.
  • Make sure that the installation area is 
strong enough to hold this product, such 
as a concrete ceiling. 
  • When this product and camera mount 
bracket are mounted on a ceiling or a wall, 
use the screws described in page 26....

14
Do not remove or loosen the internal cam-
era screws
Do not loosen the internal camera screws. 
Otherwise, water exposure may cause damage 
or malfunction of camera, or camera dropping 
may result in injury.
Radio disturbance
When this product is used near TV/radio anten-
na, strong electric field or magnetic field (near a 
motor, a transformer or a power line), images 
may be distorted and noise sound may be pro-
duced. 
PoE (Power over Ethernet)
Use a PoE hub/device that is compliant with...

15
About the initial set button
After turning off the power of the camera, turn on the power of the camera while holding down this 
button, and wait for around 5 seconds or more without releasing the button. Wait around 2 minutes 
after releasing the button. The camera will start up and the settings including the network settings 
will be initialized. Do not turn off the power of the camera during the process of initialization. Before 
initializing the settings, it is recommended to write down the...

16
IMPORTANT:
  • Remove the cover film attached to the dome 
cover after the camera installation is completed. 
After removing the cover film, do not touch the 
dome cover with your hands.
  Loosen the 3 enclosure fixing screws (M3) using 
the tamperproof screw bit (accessory).
  Remove the enclosure.
Removing the enclosure
Screw
Cover film 

17
When installing the camera on a ceiling or a wall, there are three methods as specified below.
  •  Directly mounting to a ceiling or a wall
  •  Use the supplied 
mount bracket
  •  Use the one-gang junction box
IMPORTANT:
  •  Procure 3 screws (M4) to secure the camera or the mount bracket (accessory) to a ceiling or a 
wall according to the material of the installation area. Do not use wood screws and nails.
    For mounting a camera on a concrete ceiling, use an anchor bolt (for M4) or an AY plug...

18
Method of camera installation
Installing the camera directly on the ceiling or wall
Note:
  •  Use the installation template label (accessory) with the side with the arrow facing you.
 • Ceiling installation:
    Place the installation template label so that the 
 is pointing to the front of the camera (the 
lens side).
 • Wall installation:
    Place the installation template label so that the 
 is pointing down.

Place the installation template label (accessory) on the ceiling or wall, mark the hole...

19
Using the mount bracket (accessory)
Note:
  •  When the camera is mounted on the ceiling or wall with a hole for cable running and the cables 
are passed through a conduit, the mount bracket is used.
  •  The female thread for conduit is compliant with ANSI NPSM (parallel pipe threads) 3/4 
or G3/4 
of ISO 228-1.
 
 • Ceiling installation:
    The mount bracket shall be mounted with aligning the front side (the lens side) of the camera 
with the position of the arrow in 
.
   •  Wall installation:...

20

Place the installation template label (accessory) on the ceiling or wall, mark the hole for the cable to 
be passed through and for the fixing screws (3 places), then open the holes.
Remove the installation template label, and mount the mount bracket with 3 fixing screws (locally 
procured). (
 Pages 26 and 27)

Place the installation template label (accessory) on the ceiling or wall, mark the holes for the fixing 
screws (3 places), then open the holes.
Remove the installation template label, and...