Panasonic Network Camera Wv Sw152 Wv Sw155 Installation Guide

21
Using a one-gang junction box
  •  Secure the mount bracket (accessory) to the one-gang junction box built in a ceiling or a wall.Note:
  •  Ceiling installation:
   The mount bracket shall be mounted with aligning the front side (the lens side) of the camera 
with the position of the arrow in "h".
   •  Wall installation:
   The mount bracket shall be mounted with "h" facing upward.
83.5 mm {3-9/32}
One-gang junction box
Mount bracket (accessory)
[Mounting hole pattern] 

22
Important:
  •  Before inserting the SDHC/SD memory card, turn off the power of the camera first.
  •  When inserting an SDHC/SD memory card, make sure the direction.
  •  Before  removing  the  SDHC/SD  memory  card,  select  "Not  use"  for  "SD  memory  card"  on  the  [SD memory card] tab of the setup menu first. Turn off the power after "Not use" selection, and 
then unload the SDHC/SD memory card. When the SDHC/SD memory card is inserted or 
removed with the power on,...

23
Before starting the connection, turn off the power of the devices to be connected.
Check and prepare the required devices and cables for connection.Note:
  •  Refer to pages 26 and 27 when using the mount bracket (accessory). 
  •  Refer to pages 26 and 27 when using the conduit.
z  Connect a LAN cable (category 5 or better, straight) between a PoE device (such as a hub) and 
the network connector of the camera. 

Connect a LAN cable (category 5 or better, straight, STP) between a PoE device (such as...

24
Important:
  •  Use all 4 pairs (8 pins) of the LAN cable. 
  •  The maximum cable length is 100 m {328 feet}.
  •  Make sure that the PoE device in use is compliant with IEEE802.3af standard. 
  •  When the LAN cable is disconnected once, reconnect the cable after about 2 seconds. When  the cable is quickly reconnected, the power may not be supplied from the PoE device.
Waterproof treatment for the cable joint sections
Adequate waterproof treatment is required for the cables when installing the...

25
Connection example

LAN cable (category 5 or better, straight)Important: 
  •  Use a switching hub which is compliant with 10BASE-T/100BASE-TX. 
  •  When connecting WV-SW155M cameras, use a PoE hub with M12 connectors. 
PoE device (hub)
PCLAN cable
(category 5 or better, straight)
LAN cable
(category 5 or better, straight) LAN cable
(category 5 or better, straight) 

26
Camera mounting

z Remove the dome cover. (3 screws) (☞ Page 16)
x Connect the cables to the camera. (☞ Pages 23 and 24) 
  • Waterproof the connecting portion. (
☞ Page 24) 
c  Secure the camera with 3 screws (M4) (locally procured).
Important: 
  •  Do not touch the lens. 
  •  When tightening the screws, be careful to ensure that the cables does not tangle the cables.

z Connect each cable.
   • Apply waterproof treatment to all connections. (
☞ Page 24)
x Connect the conduit attachment (locally...

27
 
z Connect each cable.
   • Apply waterproof treatment to all connections. (
☞ Page 24)
x Secure the mount bracket to the one-gang junction box. (2 screws (M4) (locally procured))
c  Secure the camera to the mount bracket with 3 fixing screws (accessory).
   (Recommended tightening torque: 1.4 N·m {1 lbf·ft})
Camera
Attachment for female thread
Conduit attachment
Mount bracket
Fixing screws
Conduit
Network cable
Camera
Mount bracket
One-gang junction box
Network cable
Fixing screws
n Ceilingn Wall 

28
Using the side cable access hole 
 
When installing the camera directly on the ceiling or wall with cables exposed, cut off a portion of 
the mount bracket to open a cable access hole. 
Cut off 

29
z Adjust the camera angle.
When determining the camera angle, repeat fine adjustments by gradually moving the panning 
table and tilting table.
  •  Attach the lens adjuster (accessory) to the lens and adjust the direction of the lens. Attach the  wider end of the lens adjuster to the lens.
  •  Do not touch the lens with your hand when making adjustments.
  •  Make  adjustments  to  the  direction  of  the  lens  while  confirming  the  picture  displayed  on  com- puter’s monitor.
  •  When...

30
Note:
  •  Depending on the vertical/horizontal angle used, the edges of the camera may be projected.
  •  Use  Extra  Zoom  when  you  want  to  adjust  the  angular  field  of  view  on  the  "Tele"  side.  When  VGA or a lower resolution is selected, the angular field of view can be adjusted without\
 deterio-
ration in the image quality.
  • 
SW155 SW155M:
If the 2x extra zoom is applied when "1280x960" or "1280x720" is selected for the image cap-
ture size, the image...