Panasonic Network Camera Wv Sw152 Wv Sw155 Installation Guide

							21
Using a one-gang junction box
  •  Secure the mount bracket (accessory) to the one-gang junction box built in a ceiling or a wall.Note:
  •  Ceiling installation:
   The mount bracket shall be mounted with aligning the front side (the lens side) of the camera 
with the position of the arrow in "h".
   •  Wall installation:
   The mount bracket shall be mounted with "h" facing upward.
83.5 mm {3-9/32}
One-gang junction box
Mount bracket (accessory)
[Mounting hole pattern] 
						

							22
Important:
  •  Before inserting the SDHC/SD memory card, turn off the power of the camera first.
  •  When inserting an SDHC/SD memory card, make sure the direction.
  •  Before  removing  the  SDHC/SD  memory  card,  select  "Not  use"  for  "SD  memory  card"  on  the  [SD memory card] tab of the setup menu first. Turn off the power after "Not use" selection, and 
then unload the SDHC/SD memory card. When the SDHC/SD memory card is inserted or 
removed with the power on, data in the SDHC/SD memory card may be damaged. (
☞ 
Operating Instructions (included in the CD-ROM))
z  Remove the dome cover. (☞ Page 16)
x   Insert an SDHC/SD memory card fully into the 
SDHC/SD memory card slot until a click is 
heard. 
c  Attach the dome cover to the camera. 
  (
☞ Page 31)
v   When removing the SDHC/SD memory card 
from the SDHC/SD memory card slot, remove 
the dome cover (
☞ page 16), and push the 
card until a click is heard. After the SDHC/SD 
memory card is removed, attach the dome 
cover to the camera again. (
☞ Page 31)
Insert/remove an SDHC/SD memory card
Label side 
						

							23
Before starting the connection, turn off the power of the devices to be connected.
Check and prepare the required devices and cables for connection.Note:
  •  Refer to pages 26 and 27 when using the mount bracket (accessory). 
  •  Refer to pages 26 and 27 when using the conduit.
z  Connect a LAN cable (category 5 or better, straight) between a PoE device (such as a hub) and 
the network connector of the camera. 

Connect a LAN cable (category 5 or better, straight, STP) between a PoE device (such as a hub) 
and the network connector of the camera.

Connect a LAN cable (category 5 or better, straight, STP) between a PoE device with M12 connec-
tors (such as a hub) and the network connector of the camera.
Connection
Network cable
Network cable
M12 connector RJ-45 (female) 
						

							24
Important:
  •  Use all 4 pairs (8 pins) of the LAN cable. 
  •  The maximum cable length is 100 m {328 feet}.
  •  Make sure that the PoE device in use is compliant with IEEE802.3af standard. 
  •  When the LAN cable is disconnected once, reconnect the cable after about 2 seconds. When  the cable is quickly reconnected, the power may not be supplied from the PoE device.
Waterproof treatment for the cable joint sections
Adequate waterproof treatment is required for the cables when installing the camera outdoors. The 
camera body is waterproof, but the cable ends are not waterproof.
Be sure to use the supplied waterproof tape at the points where the cables are connected to apply 
waterproof treatment in the following procedure. Failure to observe this or use of a tape other than 
the provided waterproof tape (such as a vinyl tape) may cause water leakage resulting in malfunc-
tion.
LAN cable
Note: How to wind the supplied waterproof tape
  •  Stretch  the  tape  by  approx.  twice  (see  the  illustration)  and wind it around the cable. Insufficient tape stretch 
causes insufficient waterproofing.
  •  Make  sure  to  wind  the  tape  so  that  it  does  not  press  down on the hook of the network cable.
  •  To  install  this  product  outdoors,  be  sure  to  waterproof  the  cables.  Waterproof grade (IEC IP66 or equivalent) is applied to this prod-
uct only when it is installed correctly as described in these operat-
ing instructions and appropriate waterproof treatment is applied. 
The mount brackets are not waterproofed.
Wind the tape in a half-o verlapping manner.
Stretch the tape to 
about twice.
2x
hook 
						

							25
Connection example

LAN cable (category 5 or better, straight)Important: 
  •  Use a switching hub which is compliant with 10BASE-T/100BASE-TX. 
  •  When connecting WV-SW155M cameras, use a PoE hub with M12 connectors. 
PoE device (hub)
PCLAN cable
(category 5 or better, straight)
LAN cable
(category 5 or better, straight) LAN cable
(category 5 or better, straight) 
						

							26
Camera mounting

z Remove the dome cover. (3 screws) (☞ Page 16)
x Connect the cables to the camera. (☞ Pages 23 and 24) 
  • Waterproof the connecting portion. (
☞ Page 24) 
c  Secure the camera with 3 screws (M4) (locally procured).
Important: 
  •  Do not touch the lens. 
  •  When tightening the screws, be careful to ensure that the cables does not tangle the cables.

z Connect each cable.
   • Apply waterproof treatment to all connections. (
☞ Page 24)
x Connect the conduit attachment (locally procured) to the conduit.
c Secure the mount bracket to the conduit attachment with the attachment for fe\
male thread 
(locally procured).
v  Mount the mount bracket to either a ceiling or a wall.
   (3 screws (M4) (locally procured))
b  Secure the camera to the mount bracket with 3 fixing screws (accessory).
   (Recommended tightening torque: 1.4 N·m {1 lbf·ft})
Installation
n Ceilingn Wall 
						

							27
 
z Connect each cable.
   • Apply waterproof treatment to all connections. (
☞ Page 24)
x Secure the mount bracket to the one-gang junction box. (2 screws (M4) (locally procured))
c  Secure the camera to the mount bracket with 3 fixing screws (accessory).
   (Recommended tightening torque: 1.4 N·m {1 lbf·ft})
Camera
Attachment for female thread
Conduit attachment
Mount bracket
Fixing screws
Conduit
Network cable
Camera
Mount bracket
One-gang junction box
Network cable
Fixing screws
n Ceilingn Wall 
						

							28
Using the side cable access hole 
 
When installing the camera directly on the ceiling or wall with cables exposed, cut off a portion of 
the mount bracket to open a cable access hole. 
Cut off 
						

							29
z Adjust the camera angle.
When determining the camera angle, repeat fine adjustments by gradually moving the panning 
table and tilting table.
  •  Attach the lens adjuster (accessory) to the lens and adjust the direction of the lens. Attach the  wider end of the lens adjuster to the lens.
  •  Do not touch the lens with your hand when making adjustments.
  •  Make  adjustments  to  the  direction  of  the  lens  while  confirming  the  picture  displayed  on  com- puter’s monitor.
  •  When adjusting the horizontal angle of cameras mounted to a ceiling, adjust the direction of the  lens by moving the lens holding the indentations on the sides of the len\
s.
Adjustment
Horizontal position : -20° to +20°
Vertical position : -20° to +90°Vertical position : -90° to +20°Vertical position : -90° to +20°
Horizontal position : -80° to +80°
n Ceilingn Wall 
						

							30
Note:
  •  Depending on the vertical/horizontal angle used, the edges of the camera may be projected.
  •  Use  Extra  Zoom  when  you  want  to  adjust  the  angular  field  of  view  on  the  "Tele"  side.  When  VGA or a lower resolution is selected, the angular field of view can be adjusted without\
 deterio-
ration in the image quality.
  • 
SW155 SW155M:
If the 2x extra zoom is applied when "1280x960" or "1280x720" is selected for the image cap-
ture size, the image quality will be deteriorated because the effect of Extra Zoom is not provid-
ed.
SW152 SW152M:
If  the  2x  extra  zoom  is  applied  when  "800x600"  is  selected  for  the  image  capture  size,  the 
image quality will be deteriorated because the effect of Extra Zoom is not provided.
x 
Attach the lens adjuster (accessory), and rotate the lens to adjust the focus of the lens.
  •  When making adjustments to the focus of the lens, attach the narrower end of the lens adjuster  to the lens.
When attaching or removing the lens adjuster, 
squeeze the wider end of the lens adjuster as 
shown in the illustration to open the narrower end 
of the lens adjuster.
Note:
  •  When the focus is difficult to adjust, set the [Zoom] button on the "Live" page to "x2".