Panasonic Network Camera Wv Sw152 Wv Sw155 Installation Guide

11
Do not touch this product or the connect-
ed cables during thunder. (even in the pro-
cess of work)
Failure to observe this may cause electric 
shock.
Turn the power off when cleaning this 
product. 
Failure to observe this may cause injury. 
[Precautions for use]
This product has no power switch. 
When turning off the power, turn off a PoE hub 
or remove a network cable. 
To keep on using with stable performance
Do not use this product in hot and humid con-
ditions for a long time. Failure to observe...

12
  •  When  some  SDHC/SD  memory  cards  are used with this product, the product may 
not work properly or performance deterio-
ration may be caused. Use the SDHC/SD 
memory cards recommended in page 40. 
Code label
The code labels (accessory) are required at 
inquiry for trouble. Use caution not to lose 
these labels. It is recommended to paste one 
of the labels onto the CD-ROM case.
About the MOS image sensor
  •  When  continuously  shooting  a  bright  light  source such as a spotlight, the color...

13
Precautions for installation
This product is designed to be installed 
under eaves.
Install the product under eaves to avoid direct 
sunlight.
Installing place
Contact your dealer for assistance if you are 
unsure of an appropriate place in your particu-
lar environment.
  •  Make  sure  that  the  installation  area  is strong enough to hold this product, such 
as a concrete ceiling. 
  •  Install the camera in the foundation area of  the architecture or where sufficient 
strength is assured.
  •  If...

14
Do not remove or loosen the internal cam-
era screws
Do  not  loosen  the  internal  camera  screws. 
Otherwise, water exposure may cause damage 
or  malfunction  of  camera,  or  camera  dropping 
may result in injury.
Radio disturbance
When  this  product  is  used  near  TV/radio 
antenna,  strong  electric  field  or  magnetic  field 
(near  a  motor,  a  transformer  or  a  power  line), 
images may be distorted and noise sound may 
be produced. 
PoE (Power over Ethernet)
Use  a  PoE  hub/device...

15
About the initial set button
After turning off the power of the camera, turn on the power of the camera while holding down this 
button, and wait for around 5 seconds or more without releasing the button. Wait around 2 minutes 
after releasing the button. The camera will start up and the settings including\
 the network settings 
will be initialized. Do not turn off the power of the camera during the process of initialization. Before 
initializing the settings, it is recommended to write down the...

16
Important:
  •  Remove  the  cover  film  attached  to  the  dome  after the camera installation is completed. After 
removing the cover film, do not touch the dome 
with your hands.
z Loosen the 3 dome cover fixing screws (M3) 
using the tamperproof screw bit (accessory).
  •  One of the screws is loosened after taking off  the screw cover.
x  Remove the dome cover.
Removing the dome cover base
Screw coverScrew
Cover film 

17
When installing the camera on a ceiling or a wall, there are three methods as specified below.
  •  Directly mounting to a ceiling or a wall
  •  Use the supplied mount bracket
  •  Use the one-gang junction boxImportant:
  •  Procure 3 screws (M4) to secure the camera or the mount bracket (accessory) to a ceiling or a  wall according to the material of the installation area. Do not use wood screws and nails.
   For mounting a camera on a concrete ceiling, use an anchor bolt (for M4) or an AY plug...

18
Method of camera installation
Installing the camera directly on the ceiling or wall
Note:
  •  Use the installation template label (accessory) with the side with the arrow facing you.
  •  Ceiling installation:
   Place the installation template label so that the "h" is pointing to the front of the camera (the 
lens side).
  •  Wall installation:
   Place the installation template label so that the "h" is pointing down.

Place the installation template label (accessory) on the ceiling...

19
Using the mount bracket (accessory)
Note:
  •  When the camera is mounted on the ceiling or wall with a hole for cable running and the cables  are passed through a conduit, the mount bracket is used.
  •  The female thread for conduit is compliant with ANSI NPSM (parallel pipe threads) 3/4"  or G3/4 
of ISO 228-1. 
  •  Ceiling installation:
   The mount bracket shall be mounted with aligning the front side (the lens side) of the camera 
with the position of the arrow in "h".
   •  Wall...

20

Place the installation template label (accessory) on the ceiling or wa\
ll, mark the hole for the cable to 
be passed through and for the fixing screws (3 places), then open the holes.
Remove the installation template label, and mount the mount bracket with\
 3 fixing screws (locally 
procured). (
☞ Pages 26 and 27)

Place the installation template label (accessory) on the ceiling or wall, mark the holes for the fixing 
screws (3 places), then open the holes.
Remove the installation template label,...