Panasonic Network Camera Kx Hcm270 Operating Instructions

Operating Instructions
[For assistance, please call: 1-800-272-7033] 91
3.5.14 Update Firmware
Update Firmware windowallows the user to install the latest version of the
Network Camera internal operating system. In most cases, this will never be
necessary. Changes may be necessary to accommodate new operating systems
or new web browsers that are not shown on page 10. In those cases, Update
Firmware would be available from the Network Camera Technical Support Site at
http://panasonic.co.jp/pcc/en/. Check...

Operating Instructions
92
4.Click[Update Firmware]on Setup Page.
5.Click[Update Firmware].
Wait about one minute.
Note
If you click[Update Firmware], operation cannot be canceled. If canceled,
refertopage124. 

Operating Instructions
[For assistance, please call: 1-800-272-7033] 93
6.Click[Browse...]to select the firmware from the file selector.
 A dialog box appears to choose the file.
7.Select a desired Firmware file (including the path information) and click
[Open].
8.Make sure the desired firmware file name is selected correctly, and click
[Update Firmware].
Restarting window is displayed, and Network Camera restarts
automatically.
Restart operation takes about one minute.
Confirm that the Update Firmware...

Operating Instructions
94
3.5.15 Reset to Factory Default
Reset to Factory Default windowinitializes all the parameters including the ID,
Password, IP address and Subnet Mask except Date and Time setting to the
factory default. Reconfirm the settings before doing the Reset to Factory Default
operation.
1.Click[Reset to Factory Default]on Setup Page.
2.Click[Execute].
 Indicator changes such asOrange blinking twice–>Tu r n i n g o f f
about 15 seconds. Initializing takes about one minute....

Operating Instructions
[For assistance, please call: 1-800-272-7033] 95
Section4
Technical Guides 

Operating Instructions
96
4.1 Network Camera Installation
Outdoor Installation
Network Camera has a splash resistant body. The splash resistant body allows
Network Camera to be used indoors and outdoors. Waterproof cabling is
necessary for outdoor mounting. Check Network Camera operation before
installing (cabling and mounting) Network Camera.
Notes
 Install Network Camera under eaves to protect it from direct sunlight.
Prolonged exposure to direct sunlight or halogen light may damage the CMOS
sensor.
...

Operating Instructions
[For assistance, please call: 1-800-272-7033] 97
High performance for wireless communication
Radio waves from the antenna of Network Camera transmit images. The
performance of wireless communication will change under the condition where
you install Network Camera and wireless router.Wireless windowon page 32
displays the data communication and signal strength status of the wireless
network.
Notes
 Install Network Camera away from electrical appliances such as TVs or
cordless...

Operating Instructions
98
4.1.1 Network Camera Cabling
Check the location where Network Camera should be installed. Select the proper
cablesuitedtoNetworkCameralocation.Consultanauthorizedwiringelectrician
for cabling.
1.Raise the antenna vertically(1.), and put the cables through the Connector
Cover(2.). Connect the DC plug of the AC adaptor to the DC IN jack(3.).
Connect the AC plug of the AC adaptor to the power outlet(4.).
Notes
 Mounting and cabling instructions described in this Operating...

Operating Instructions
[For assistance, please call: 1-800-272-7033] 99
2.Thread the AC adaptor cord through the hook. Put the Rubber Cap and the
Connector Cover by fastening the three screws in numerical order. The
remaining screw hole on the Connector Cover is used for attaching Sunshade.
Note
Be sure to thread the AC adaptor cord through the hook.
3.Attach the Sunshade by fastening the two screws.
Connector Cover
HookAC
adaptor
cord
1
2
3
Carefully insert the
Rubber Cap into the
hole, gently pressing...

Operating Instructions
100
4.Roll up three putties around the cables and fit them into the holes to prevent
water from getting inside Network Camera. Use last putty to fix the spot.
Notes
 Confirm Network Camera is functioning before puttying the cables.
Putties and Self Bonding tape cannot be used twice.
 Check the length and the type of the Ethernet cable before fixing with
putty.
5.Cover the putties by rolling.
 Self Bonding tape is used to mount Network Camera on a wall or ceiling,
so leave half...