Panasonic Network Camera Bl Vp101 Manual

 31 
28．Addition of “Audio output duration” setting 
( Operating Instructions Configure the settings relating to images and audio [Image/Audio] 
- Configure the settings relating to audio [Audio] ) 
 
 (E xcluding  SW314,  VP104, VP104W , VP101 ) 
 
［Audio output duration］ 
Configure the maximum duration for each time audio is outputted.  
1min／ 2min／3min／5min／10min／ 20min／ 30min／1h 
Default: 5min  
Note 
・ Audio output stops when  the specified time has passed. To turn the audio transmission function...

 32 
29．Addition of “Alarm deactivation time” setting 
( Operating Instructions Configure the alarm settings [Alarm] - Configure the settings 
relating to the alarm action [Alarm] ) 
 
［Alarm deactivation time］ 
Configure the duration that detections won't be made after an alarm is detected. For example, by using this 
function you can prevent mail from being sent too often when mail notifications are c onfigured to be sent to 
cellular phones when an alarm is detected.  
5s ／10s ／30s ／1min／ 3min／...

 33 
30．Addition of pre alarm to FTP alarm transmission 
( Operating Instructions Configure the alarm settings [Alarm] - Configure the settings 
relating to the alarm image [Alarm] ) 
 
［FTP transmission retry］ 
Select "On" or "Off" to determine whether or not to resend failed FTP transmissions. 
On: If transmission fails, transmissions are resent until they are successfully sent. 
Off: If transmission fails, the image that failed to be sent is discarded and the next image is sent....

 34 
Note 
・When "On" is selected for "Image compression rate upon alarm detection" , only post alarm recorded 
images are compressed. Compression is not applied to pre alarm recorded images.  
・When a selection with an asterisk (*) on the right of it is selected for " Maximum number of images" of  
"Pre alarm", the specified number of images m ay not be able to be sent depending on the image capture  
size and image 
 quality. The following table shows the maximum number...

 35 
32．Changes to image attachments for E-mail information 
( Operating Instructions Configure the alarm settings [Alarm] - Configuration of the 
settings relating to the E-mail notification [Notification] ) 
 
 
 
"Alarm image attachment" can now be activated (set to "On") even if "H.264(1)" or "H.264(2)" is selected for 
"Recording format" ([SD memory card] tab of the "Basic" page)
. 
Note 
・ The settings for “ Image capture size”  of the “ Alarm image”...

 36 
34. Warning outputs, usage information, and error information display have 
been added for SD memory cards 
( Operating Instructions Configure the alarm settings [Alarm] - Configure the settings 
relating to the alarm output terminal [Alarm], Maintenance of the camera [Maintenance] - 
Check the status [Status] ) 
 
*Only the model corresponding to an SD memory card 
 
■Addition of SD memory card error outputs 
Warnings can output from the alarm output terminal if an error occurs for the SD memory...

 37 
・Output  signals from the alarm output terminal for [SD memory card error ] differ depending on 
  the settings of [Alarm output type].  
-  When  "Latch" is selected: Even after you click the "Alarm occurrence indication" button and  
  it disappears, 
output  signals from the alarm output terminal will continue as long as the cause of  
  the [SD memory card error] is not resolved.  
-  When "Pulse" is select ed: Even after you click the "Alarm occurrence...

 38 
Note 
Because the overwrite time values are just estimates calculated by the camera, they may differ to the actual 
number of overwrite times.  
 
[No] / [Time & date] / [Description] of the log 
Displays the log related to the SD memory card.  
Category Indication Description 
SD memory card  Format Successfully formatted the SD memory card. 
 Format error An error occurred when formatting the SD memory card. 
 Write-protect 
ON (Locked card) 
A write -protected SD memory card is inserted....

 39 
35. Changes to connection information and warning display of the power 
supply device 
( Installation guide Precautions, Operating Instructions Maintenance of the camera 
[Maintenance] - Check the system log [System log], About the displayed system log ) 
*W V-SW396, WV- SW396A, WV -SW395, WV- SW395A 
The warning display for when the correct power supply device is not connected has change from the OSD to 
the [System log] tab on the  “Maintenance”  page. If a warning is displayed, check that the...

 40 
36 Addition of “VBR” to the “Transmission priority” of “H.264” 
 ( Operating Instructions Configure the settings relating to images and audio [Image/Audio] 
- Configure the settings relating to H.264 images [JPEG/H.264] )  
[Transmission priority] 
Select a transmission priority for H.264 images from the following. 
• Constant bit rate: H.264 images will be transmitted with the bit rate selected for  “Max bit rate (per  client)  *”. 
•  VBR: H.264 images will be transmitted with the frame rate...