Panasonic Network Camera Bl Vp101 Manual

 11 
[Transmission priority] 
Select a transmission priority for H.264 images from the following.  
• Constant bit rate: H.264 images will be transmitted with the bit rate selected for “Max bit rate (per  
client) *”. 
• Frame rate: H.264 images will be transmitted with the frame rate selected for “Frame rate*”.  
• Best effort: In accordance with the network bandwidth, H.264 images will be transmitted with the bit rate 
varying between the maximum and minimum bit rates that are set for “Max bit r ate...

 12 
10. Addition of “Advanced VBR” to the “H.264 recording” 
( Operating Instructions Configure the basic settings of the camera [Basic] - Configure the 
settings relating to the SD memory card [SD memory card] ) 
 
 
 
 
 
 
 
 
 
 
 
 
 
[Recording priority] 
From the following, select a recording priority for H.264 images to be recorded. 
• Constant bit rate: H.264 images will be recorded with the bit rate selected for “Max bit rate”.  
• Frame rate: H.264 images will be recorded with the frame rate...

 13 
11. Addition of “Focus distance” of Focus 
( Operating Instructions Configure the settings relating to images and audio [Image/Audio] - 
Configure the settings relating to the camera operations [Cam. Function] ) 
 
 
[Focus distance] 
When shooting a subject through glass or when an object other than the subject is close to the camera when 
shooting, it may be difficult to focus on the subject. In this case, the minimum focus distance can be limited. 
• Unlimited: Does not limit the minimum focus...

 14 
12. Addition of “Fog compensation” settings 
( Operating Instructions Configure the settings relating to images and audio [Image/Audio] - 
Configure the settings relating to images and the preset positions [Image/Position] - 
Configure the settings relating to image quality (“Image adjust” setup menu ) ) 
 
( Operating Instructions Configure the settings relating to images and audio [Image/Audio] - 
Configure the settings relating to image adjust, zoom, extra optical zoom, extra zoom, focus, 
back...

 15 
[Level] 
Adjust the fog compensation level. 
The level of fog compensation will increase when the cursor is moved in the “+” direction, and decrease when 
the cursor is moved in the “ -” direction.  Click the [Reset] button to reset to the default setting.  
Default: 64  
 
13. Addition of “Intensity control “ to the “IR LED Light” 
( Operating Instructions Configure the settings relating to images and audio [Image/Audio] - 
Configure the settings relating to image adjust, zoom, extra optical zoom,...

 16 
14. Addition of “Pan/Tilt limitation” settings 
( Operating Instructions Configure the settings relating to images and audio [Image/Audio] - 
Configure the settings relating to images and the preset positions [Image/Position] ) 
 * Excluding  BL -VP101, BL -VP104, BL -VP104W 
 
 
[Pan/Tilt limitation] 
Select "On" or "Off" to determine whether or not to enable limiting the range of pan/tilt operations.  
Select "On", adjust the angle of view with  the control pad/buttons, and...

 17 
Note 
・Configure the angles of "Left end position" and "Bottom position" so that they are lower tha n the angles of 
"Right end position" and "Top position" respectively.  
・ "Brightness" cannot be saved.  
・ Configure the tilt angle for pan/tilt when the screen is not zoomed in on.    Even if the tilt angle for pan/tilt is 
configured when the screen is zoomed in  on, when the display size is returned to x1, an area outside the 
configured tilt angle will be...

 18 
• Alarm input: Receives alarms. When “Alarm input” is selected, a pull -down menu for “Close” and  
“Open” is displayed.  
– Close: An alarm is detected when the terminal status is changed to “Close”.  
– Open: An alarm is detected when the terminal status is changed to “Open”.  
• Alarm output: Alarm output will be carried out according to the settings for “Alarm output terminal  
setup”  
Default: Off 
[Terminal 3] *1 
Determine how to use terminal 3.  
• Off: Not used. 
• Alarm input: Receives...

 19 
16. Addition of “HTTP alarm notification” 
( Operating Instructions Configure the alarm settings [Alarm] )  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
[Address 1] - [Address 5] 
Enter the IP address or the host name of the HTTP server. Up to 5 destination server addresses can be 
registered.  
Available characters： Alphanumeric characters, the colon (:), the period (.), the underscore (_), and  
the hyphen (-) 
Default： http:// 
Entry exampl e: "http://IP address: (colon) + port number" or...

 20 
[Notification data] 
Configure the notification data to be added to the end of the HTTP server configured in "Address". 
Default： /cgi-bin/comalarm.cgi?CMD=01   
Note 
・For “Address 1” to “Address 5”, a total of 256 characters can be  entered for the address (including“http://”) 
and “Notification data”.  
・ Make sure to enter "/" as the first character for "Notification data".  
・ Even if the [Set] button is clicked after deleting the contents of “ Notification data”,...