Panasonic Network Camera BL-C30C Operating Instructions

Operating Instructions
21
Viewing the Image
1.Click the home position, sensor 
position or registered preset button.
 The camera takes each position, 
and the image is displayed.
Sensor 
Position
Pan/Tilt
Putting the 
cursor displays 
the preset 
name.Home 
Position
UpperLeft 

Operating Instructions
22
Changing or Deleting the Settings
1.Click [Program].
 [Program] switches to [Cancel]. 
Click [Cancel] to quit without saving 
changes.
2.Pan and tilt the camera to a desired 
position.
 When deleting, this step is not 
necessary.
3.Click the home position, sensor position 
or a preset button (1—8).
4.Click [Save] after setting the preset 
name or click [Delete].
 If you quit to change or delete 
settings, click [Back], and then 
[Cancel].
 If Success! is displayed, click...

Operating Instructions
23
1.3 Viewing Multi-Camera page
To view multiple cameras on the Multi-Camera page, you need to configure each 
camera on the Multi-Camera Setup page (see page 
58).
1.Access the camera (see page 8).
 The Top page is displayed.
2.Click the [Multi] tab at the top of the page.
 Multi-Camera page can display up to 12 camera images.
3.Close the web browser.
Capture Image Button (See page 16)
Switches cameras to 
display.
Selects [320 x 240] 
(default) or [160 x 120] 
pixels...

Operating Instructions
24
Notes
 When selecting [All] at the View Type, all images are displayed in 160 x 
120 pixels resolution.
 640 x 480 pixels image cannot be displayed on the Multi-Camera page.
 When viewing video (Motion JPEG), we recommend using an Ethernet 
switching hub instead of the repeater hub to prevent degradation in video 
display.
 Due to the network congestion or the number of accesses, the refresh 
interval may slow down.
 When the refresh interval is slow, restrict the bandwidth...

Operating Instructions
25
1.4 Viewing Buffered Image page
To buffer the images on the internal memory, you need to set up image transfer 
settings (see page 
60 or page 69). You can view buffered images on this Buffered 
Image page.
1.Access the camera (see page 8).
 The Top page is displayed.
2.Click the [Buffered Image] tab at the top of the page.
3.Click the trigger number.
The trigger number is displayed (see page 60 or page 69).
 
 
The trigger is displayed 
(see page 
60 or page 69). 

Operating Instructions
26
4.Display images clicking buttons below.
Notes
 Date, Time and frame number are not displayed in play mode.
 Maximum number of buffered images change depending on resolution, image 
quality and what object the camera buffers. At the 320 x 240 pixels resolution 
and the standard quality, the camera buffers about 250 frames (see page 
115).  
(If 3 trigger settings are enabled, the internal memory capacity is divided into 
3 sections. In this case, each trigger can buffer about...

Operating Instructions
27
1.5 Viewing Still Images on Your Cell Phone
You can view still images over the Internet from a compatible cell phone.
Enter http://IP address (or URL):Port Number/mobile on a cell phone and press [OK]. 
 When the port number is set to 80 (default), it is not required.
 The Internet access to the camera must be allowed for cell phone access.
 When an authentication window is displayed, enter the administrators or the 
general users user name and password.
 A still image is...

Operating Instructions
28
Notes
 Not all Cellular Service Providers permit this camera function. Check with your 
Cellular Service Provider for compatibility.
 If the image is not displayed properly, try the following 2 URLs.
 Only an administrator can control privacy mode.
 In privacy mode, sensor and timer image buffer/transfer features also are 
stopped. 
 When executing [Privacy Mode] while setting [Permit access from guest users] 
on the Security: Administrator page (see page 
49), an...

Operating Instructions
29
2 Various Camera Features
2.1 Using Camera Features
1.Access the camera (see page 8).
 The Top page is displayed.
Notes
 When [Permit access from guest users] is set on the Security: 
Administrator page, click [Login] tab and log in as an administrator.
 When users other than an administrator are accessing the camera, the 
[Setup] and [Maintenance] tabs are not displayed.
2.Click [Setup] tab at the top of the page.
(1)(2)(3)(4)(5)(6)
(7)(8)
(9)
(10)(11)(12)(13)(14) 

Operating Instructions
30
Basic
(1)NetworkConfigures the network settings such as connection mode 
to connect the camera to the network (see page 
32).
(2)WirelessConfigures wireless network (see page 37).
(3)UPnPEnables automatic port forwarding or shortcut to the 
camera (see page 
40).
(4)Viewnetcam. 
com
Registers with the Viewnetcam.com service (see page 41).
(5)Date and TimeSets the date and time, automatic time adjustment and 
adjust clock for daylight saving time settings (see page 
43)....