Panasonic Network Camera Bb Hcm331a Operating Instructions

Operating Instructions
101[For assistance, please call: 1-800-272-7033]
9.After you confirm the settings and click [Next>], set E-mail notification and click 
[Next>].
• If you select [Enable], the E-mail Notification When Triggered page is 
displayed. Enter the settings seeing page 99 and page 100. When 
finished, click [Next>] and go to step 10.
10.Click [Save] after confirming the settings.
• New settings are saved.
• When finished, "Success!" is displayed.
Note
If you click [Save], all...

Operating Instructions
102
11 .Click [Go to Image Buffer/Transfer page].
• The Image Buffer/Transfer page is displayed.
Notes
• If you set a short interval to transfer image to a mobile phone, many E-
mails may be sent to it leading to a large phone bill. Therefore, we 
recommend you to set a long interval. 1 image per second frequency is 
recommended.
• Alarm transfer stops its operations until the camera finishes all transfers. 
For example, if the camera transfers 3 images per minute and 6 images in...

Operating Instructions
103[For assistance, please call: 1-800-272-7033]
2.21 Transfer the Camera Image in Transport Mode
The camera can transfer the image in transport mode by E-mail or FTP.
Prepare the following requirements.
See page 51 and set up the E-mail or FTP server.ItemSupported Feature
E-mail or FTP 
ServerOperating 
System
ISP Service: IPsec supported
: Services for multiple static global 
addresses (A global address must be set up 
to the server.)
Camera ISP Service : Services for multiple...

Operating Instructions
104
2.22 Transfer the Camera Image in Tunnel Mode
The camera can transfer the image in tunnel mode by E-mail or FTP.
Prepare the following requirements.
See page 54 and set up the E-mail or FTP server.ItemSupported Feature
VPN Router ISP Service
(in IPv4)
ISP Service
(in IPv6): Services for static global addresses (A 
global address must be set up to the WAN 
side.)
: "IPv4/IPv6 Dual-Stack" or "IPv6 over IPv4 
Tunneling" service
Camera ISP Service
(in IPv4)
ISP...

Operating Instructions
105[For assistance, please call: 1-800-272-7033]
2.23 Specifying Operation Time
The Operation Time page allows you to limit the operation time. The camera image 
turns to a gray screen outside the operation time.
Notes
• If you wrongly set the time period, your privacy may be seen. Confirm the 
time period after the setup.
• If you access the camera as an administrator, you can view the image 
outside the time period.
1.Click [Operation Time] on the Setup page.
2.Click [No.] to set...

Operating Instructions
106
4.Click [Save] when finished.
• New settings are saved.
• The Operation Time page is displayed.
About Operation Time
In the operation time settings, the enabled settings take priority over the disabled 
settings. Therefore, if Monday or Tuesday is disabled in a setting but enabled in 
other settings, the camera can be operated on both Monday and Tuesday.
Note
An administrator can view images anytime regardless of the setting for the 
operation time.Setting Description
Enable •...

Operating Instructions
107[For assistance, please call: 1-800-272-7033]
2.24 Controlling External Output Terminal
The digital output terminal allows you to control the external devices. You can 
change the initial status of the output signal.
1.Click [External Output] on the Setup page.
2.Click [Save] when finished.
• Clicking [Cancel] cancels your settings without saving changes.
• New settings are saved.
• When finished, "Success!" is displayed. 
3.Click [Go to External Output Control page].
•...

Operating Instructions
108
2.25 Changing Indicator Display
The Indicator Control page allows you to select Indicator operation. Indicator has 
three options.
•Always on
• Turn the indicator on when the camera is accessed.
•Always off
1.Click [Indicator Control] on the Setup page.
2.Select indicator option.
• Clicking [Cancel] cancels your settings without saving changes.
Notes
• See page 11 in the Installation/Troubleshooting for indicator display.
• Selecting [Never turn indicator on] keeps indicator...

Operating Instructions
109[For assistance, please call: 1-800-272-7033]
3 Camera Maintenance
3.1 Maintenance page
Maintenance
(14) StatusDisplays the camera settings and status (see page 110).
(15) RestartRestarts the camera (see page 110).
(16) Update FirmwareUpdates the camera firmware (see page 111).
(17) Save SettingsCreates a configuration file (see page 114).
(18) Load SettingsLoads settings from a configuration file (see page 115).
(19) Reset to Factory 
DefaultResets the camera to its default...

Operating Instructions
11 0
3.1.1 Confirming the Status
The Status page allows you to check the status of the camera. The status 
information provides support for troubleshooting.
Clicking [Status] displays the following page.
Note
See Panasonic Network Camera support website at http://panasonic.co.jp/
pcc/products/en/netwkcam/ for details about status information.
3.1.2 Restarting the Camera
The camera restarts by disconnecting the power cord from the outlet and 
reconnecting it again. The camera can...