Panasonic Monitoring System BL-MS103 Operating Instructions

							6 Setup Menu
100
Note
• Please be aware that when you make changes to values set during Quick 
Setup, you may lose access to the network.
• If you make a mistake while changing these settings, use the FACTORY 
DEFAULT RESET button to restore the BL-WV10A's default settings (see 
page 131). Doing so, however, will reset all of your settings to their defaults, and 
sever the connections to the cameras. You will need to re-perform Quick Setup 
to register the cameras and set desired settings again.
Camera Settings
Change the camera network settings.
Note
• The administrator name and password must be between 6 and 15 
alphanumeric characters in length. The following characters cannot be used:
"  <  >  :  &.
• When you re-register cameras using Quick Setup after changing the 
administrator name and password, the user name and password for the camera 
SettingDescription
Starting AddressSet the IP address to be used when a camera is 
configured using Quick Setup. A maximum of 8 
addresses will be created and used, starting 
sequentially from this entry. If you run Quick Setup 
after connecting a BB-HGW700A, the starting 
address will be displayed as [Auto] and cannot be 
set manually.
Admin User NameSet the user name for local cameras for Quick Setup. 
This user name is used when connecting to local 
cameras.
Admin PasswordSet the password for local cameras for Quick Setup. 
This password is used when connecting to local 
cameras. 
						

							6 Setup Menu
[For assistance, please call: 1-800-272-7033] 101
will be changed to the new administrator name and password. The new 
administrator name and password will not overwrite user names and 
passwords for cameras that have already been registered. You will continue to 
be able to use the existing user names and passwords for those local cameras. 
To re-register those cameras with the new administrator name and password, 
see page 134.
• If you aren't planning to access a camera with a computer, it is not necessary 
to set an administrator name and password.
Wireless Settings
Change the wireless settings for the BL-WV10A.
SettingDescription
Wireless ModeChoose either repeater or access point mode. When the BL-
WV10A is connected to a BB-HGW700A wirelessly, Quick 
Setup will automatically change this setting to repeater mode.
Wireless 
FormatChoose from 802.11b, 802.11g only or 802.11b/g.
SSIDSet the identifier for the wireless network local in use.
SSID Stealth 
ModeChoose either [Enabled] or [Disabled].
To make wireless LAN networks easier to detect, the network 
identifier, or SSID, is regularly transmitted. Turning the stealth 
features off will allow the network to be easily detected, but 
unauthorized users may also attempt to access the network as 
a result, resulting in a possible security issue. Turning the 
stealth features on will deny access through ANY key, making 
the network harder to detect. 
						

							6 Setup Menu
102
Note
• Use the same encryption key number and type for any wireless terminal to be 
connected.
Note
• To register a BL-C30A, you will need to specify 2 MAC addresses. Choose the 
MAC address indicated on the base of the BL-C30A and one from the following 
table based on the last digit in the BL-C30A's MAC address.
For example, if the MAC address for the BL-C30A is 00:80:F0:54:C0:C4, you 
should specify 00:80:F0:54:C0:C4 and 00:80:F0:54:C0:C5.
Certain changes may require the BL-WV10A to restart.ChannelThe communications channel to be used can be chosen from 
either AUTO or a number between 1 and 11.
Choosing AUTO will allow the BL-WV10A to automatically 
detect an available channel at launch. If the quality of the 
connection is not, you can manually choose another channel 
as well.
EncryptionChoose to turn encryption either on or off.
Sets an encryption key when encryption is turned on.
Encryption 
KeySets an encryption key when encryption is turned on.
Up to 4 encryption keys can be set in advance.
Allowable keys:
Choose from encryption keys 1 through 4 to use with 
encryption.
Key types:
The types of encryption keys are 64 bit (10 hexadecimal digits 
or 5 letters), 128 bit (26 hexadecimal digits or 13 letters), or 152 
bit (32 hexadecimal digits or 16 letters). The level of security 
increases with the number of bits, but there may be a slight 
decrease in network speed as a result.
Keys 1 through 4:
Enter an encryption key that corresponds in length to the type 
selected.
MAC Address 
FilteringChoose to either turn MAC address filtering (to specify the 
addresses of connected devices) on or off. Turning it on will 
allow you to specify the MAC addresses of the devices which 
are allowed to connect. Up to 16 address can be specified.
0 —> 1 2 —> 3 4 —> 5 6 —> 7 8 —> 9 A —> B C —> D E —> F
SettingDescription 
						

							6 Setup Menu
[For assistance, please call: 1-800-272-7033] 103
1.If after making changes a restart is needed, the [Restart] tab will appear.
2.Select the [Restart] tab and the [Restart] button will appear.
3.Press the [Restart] button, and the Restart Confirmation screen will appear. 
Select [Yes] and press [ENTER] to restart the BL-WV10A.
Note
• Please be aware that when you make changes to values set during Quick 
Setup, you may lose access to the network.
Restart tab 
						

							6 Setup Menu
104
Sensor Settings
The BL-WV10A displays an account name and password for its FTP server in order 
to receive sensor-detected images from the cameras.
Note
• The FTP account name and password are set automatically. Change them to 
increase security when necessary.
• The FTP account name and password must be between 6 and 15 
alphanumeric characters in length. " cannot be used.
SettingDescription
FTP User NameSet the account name to log on to the FTP server within the 
BL-WV10A.
FTP PasswordSet the password to log on to the FTP server within the BL-
WV10A. 
						

							6 Setup Menu
[For assistance, please call: 1-800-272-7033] 105
Status Settings
Displays a list of settings
6.3 Registering a Camera Manually
1.Select [Camera Setup] from the [Setup] screen (see page 95) and press 
[ENTER].
• The security screen appears.
2.Enter the security code.
• The default code is 9999.
SettingDescription
Vers i o nDisplays information on the BL-WV10A firmware and the 
wireless firmware.
NetworkDisplays the IP address, subnet mask, DNS servers, proxy 
server, proxy port and MAC address values.
WirelessDisplays the communications mode, SSID, wireless stealth 
status, communications channel, BSSID, MAC address 
filtering status and encryption values. 
						

							6 Setup Menu
106
• The Camera Setup screen appears.
Note
• Local cameras are designated with the word "Local" in the right-hand 
column.
3.Select [–] from the list of registered cameras and press [ENTER].
• The New Camera Registration screen appears.
4.Enter the appropriate settings.
SettingDescription
CameraSets the camera name. Select [Camera] and press 
[ENTER] to display the character input screen. (See 
page 121 for more information on text entry.) Specify a 
name for the camera using between 1 and 15 alphanumeric 
characters. Registration will occur without this setting.
Address:PortSets the IP address or URL and the port number for the 
camera.
Enter in the following format: IP address:port number or 
URL:port number. 
						

							6 Setup Menu
[For assistance, please call: 1-800-272-7033] 107
5.Select [Save] and press [ENTER].
• If you select [Cancel] and press [ENTER], the entered settings will not be 
registered.
Note
• When registering a camera via the Internet, set the camera's IP address 
or URL and its port number in the camera address setting. When using a 
URL for a camera address, be sure to set the correct IP address for the 
DNS servers in the [General Setup] screen (see page 99).
• When entering the camera address and port number, ‘http://' should be 
omitted.
Note
• Registering a camera manually will make it a remote camera. Use Quick 
Setup to register a camera as a local camera (see page 20). Proxy ServerTurns the use of a proxy server on or off.
Turn this setting on if a proxy server is needed to access the 
camera's URL or IP address. Also, enter the proxy server 
and port indicated in the [General Setup] screen (see 
page 99).
User NameSets the user name for the camera.
Password SaveSets the option to save the camera password.
Turning it off will require the entry of a user name and 
password whenever a camera is accessed.
• Turning off password saving will disable timer 
recording settings (see page 78).
PasswordSets the camera password.
ConfirmConfirms the image of the camera being configured. If an 
image is not visible, double check the settings above. After 
confirming the image, proceed to step 5.
SettingDescription 
						

							6 Setup Menu
108
6.4 Camera Setup
You can change camera settings.
You can also erase a camera from the list or change its position in the list.
1.Select [Camera Setup] from the [Setup] screen (see page 95) and press 
[ENTER].
2.Select the camera whose settings you wish to change and press [ENTER].
• When the selected camera is a local camera, the Local Camera Setup 
screen will appear; for remote cameras, the Remote Camera Setup 
screen will appear.
Local Camera Setup Screen
Remote Camera Setup Screen 
						

							6 Setup Menu
[For assistance, please call: 1-800-272-7033] 109
Note
• When you select a local camera using the Privacy Mode feature, the 
Disable Privacy Mode screen will appear. To change camera settings, 
select [Yes] to disable the Privacy Mode feature.
3.Enter the appropriate settings.
• For local cameras, see page 109. For remote cameras, see page 114.
6.4.1 Camera Setup for Local Cameras
Camera Information
SettingDescription
CameraDisplay and change the camera name.
Select [Camera] and press [ENTER] to display the character 
input screen. (See page 121 for more information on text 
entry.)
AC Power 
FrequencyChoose either [50 Hz] or [60 Hz].
Choose either 50 Hz 60 Hz (typically 60 Hz should be 
selected).