Panasonic Memory Card Video Recorder AG-CPD15P Operating Instructions

71
Operation Using the Remote 
Control Panel (separately sold)
Notes:
•  An interrupted restore process can 
be resumed at a later time. 
•  
Recording is still available even if 
there are files in need of restoration. 
•  A recording trigger detected during 
a restore process or pressing the 
[REC] button will interrupt the 
process and start recording. 
•  Files that must be restored do not 
appear on the playback file list 
screen. Make sure to restore the 
files beforehand.
•  Since a seriously...

72
  Viewing error log data
Use the following procedure to open a 
dialog showing up to five of the most 
recent errors.
1.  Perform steps 1 to 3 in 
“Viewing P2 card type and 
software version”.
2.  
This selects [Last Errors]. 
Press the [
] button to accept.
This dialog shows the most recent 
error data (the items listed below).
• Month/day (MM/DD)
• Hour/minute (HH : MM)
• Error No. 
• Error type (Fatal Error/Error)
•  Error message (the first 40 
characters appear)
Notes:
•  Error data with a low...

Setup/Admin [1/2]
Rec/Play
Date/Time
OSDTrigger
Management ModeCamera
Registration
Programed Rec
73
Administrator Operations on the 
Remote Control Panel (separately sold)
The setup of this unit includes items 
that only an administrator is allowed to 
set up.
Notes:
•  Starting up a PC application 
during Administrator  Setup  aborts 
Administrator Setup. This unit will 
then freeze in the live screen and 
disable Administrator  Setup. 
•  Starting Administrator  Setup 
from a PC application causes the...

Authentication
Since you are not an administrator, 
you cannot open this menu.
74
If officer data is already registered for 
the administrator but is not identical, 
the following screen appears before 
the Menu automatically reappears. 
Obtain correct data from the 
administrator and repeat operations 
from Step 1 above.
Note:
Refer to “Setup” on pages 35 - 42 for 
information on the factory defaults.
Administrator Setup (continued) 

75
Administrator Operations on the 
Remote Control Panel (separately sold)
Rec/Play
  PowerOff Time
Use this function to set the interval 
after which the Remote Control 
Panel and this unit will shut down 
after the ignition switch has been 
set to the LOCK (OFF) position.
 
Setting (min.): 
        0, 10, 20, 30, 60, 90, 120, 
180, AUTO
∗1
  Init Camera Select
Select the camera selected at power-on. 
1:     Color Camera connected to 
the [CAMERA1] connector
2:     
Commercially available camera...

76
  Rec Continue Time∗1
Use this function to set recording 
continue time for normal recording 
when a trigger is entered or when 
the [REC] button is pressed.
Setting (min.) :   
1, 2, 5, 10, 15, 20, 30, 
60, 90, CONTINUE
  PreRec Time (Video)∗2
Use this function to set how much of 
already stored video will be retained 
when a trigger is entered or the 
[REC] button is pressed.
Setting (sec.) : 0, 10, 20, 30, 60, 90
  PreRec Time (Audio)∗2
Use this function to set how much of 
already stored audio...

77
Administrator Operations on the 
Remote Control Panel (separately sold)
  GPIO9 for Rec
Enables or disables output of 
recording status signals to GPIO9.
When enabled, a high level (output 
voltage 5 V) indicates recording is 
in progress.
Setting :  ENABLE, DISABLE
  GPIO9 for Error
Enables or disables output of recording 
error status signals to GPIO9.
 
When enabled, a high level (output 
voltage 5 V) and a low level (output 
voltage 0 V) change at high speed to 
indicate recording error status....

78
Administrator Setup (continued)
Skip Target
Use this function to set the skip 
location (the amount of time that is 
skipped) when the [Skip back] or [Skip 
forward] button is pressed.
  Trigger / Marker
 
Playback jumps to the trigger 
position (one per file) at which 
recording began, or to a bookmark 
position, whichever found earlier. 
However, no trigger position can 
exist in automatically divided files. 
Setting : YES, NO
  Head of File
Use this function to move to the 
beginning of a file...

79
Administrator Operations on the 
Remote Control Panel (separately sold)
Date/Time
  TimeZone
Indicates time difference from world 
standard time. 
Hawaii    :  Hawaiian standard time
Yukon     :  Alaska standard time
Yukon DST :  Alaska daylight saving time
Pacific    :  Pacific standard time
Pacific DST :   Pacific daylight saving time
Mountain   :   Mountain standard time
Mountain DST :  Mountain daylight saving time
Central    :  Central standard time
Central DST :  Central daylight saving time...

80
OSD
  OSD
Use this function to set whether the 
On-Screen Display appears on the 
screen and is included in record files.
Setting : ON, OFF
  Display Position
Use this function to set the display 
position for the On-Screen Display on 
the screen and in record files.
 
L-Upper     : Upper left 
R-Upper     : Upper right 
L-Bottom   :  Lower  left 
R-Bottom  : Lower right • In NONE mode
H       : High-edge trigger
L       : Low-edge trigger
SPEED :  Detects vehicle speed 
(GPIO8 only)
Notes:
•  When...