Panasonic Lifi Hdtv Pt 50lcz70 Operating Instructions

21
Getting Start ed
These diagrams show our recommendations for how to connect this Projecti\
on Display to your various equipment.
For other connections, consult the instructions and the specifications f\
or each piece of equipment. (p. 63)
For additional assistance, please visit our website at:  www.panasonic.com
 www.panasonic.ca
Notes
The picture and audio input signals connected to a terminal specified in\
 “Monitor out” (p. 50) cannot be output from “OUTPUT” 
terminals. However, audio output can be...

22
 EZ Sync™ Connections
Follow the connection diagrams below for HDAVI control 
of a single AV piece of equipment such as a Panasonic 
DIGA-DVD recorder, RAM theater, or Player theater system. 
Refer to pages 52-54 for Setup Menu settings and additional 
control information.Optional HDMI and/or optical cables are not provided.
•
If the connection (or settings) of equipment compatible with 
HDAVI control has been changed, switch the power of this 
unit Off then On again while the power of all equipment...

23
Getting Start ed
HDMI connection
HDMI (high-definition multimedia interface) allows you to enjoy high-d\
efinition digital images and high-quality sound by 
connecting this Projection Display and the devices.
HDMI-compatible equipment (*1) with an HDMI or DVI output terminal, su\
ch as a Set Top Box or a DVD player, can be 
connected to the HDMI connector using an HDMI compliant (fully wired) \
cable.
HDMI is the world’s first complete digital consumer AV interface comp\
lying with a non-compression...

24
Turning the Power ON and OFF
Always be sure to follow the procedure given below to 
turn the Projection Display power ON and OFF.
The lamp cooling fan will continue to operate for 
approximately 3 minutes after the power is turned off. During 
this time, the POWER indicator will blink Red.
Do not disconnect the power cord from the outlet 
and do not open the circuit breaker (unless 
necessary) while the cooling fan is still operating. Do 
not disconnect the power cord from the power outlet 
while the...

25
Basic Operation
 First Time Setup
For your convenience, First Time Setup menu will 
be displayed on screen when the set is turned on 
for the first time. If needed, follow the menus and 
procedures displayed on-screen for setting up the 
features.
Language
The language of the on-screen display is set to English 
as the factory setting. You can select English, Spanish or 
French as the on-screen display language.
Procedure
1. Press ▲▼ to select “Language”.
2.  Press OK to display the Language menu.
3....

26
 Switching languages for display
Allows you to select the language used for 
On-Screen Displays.
Procedure
1.  Press MENU to display the Main Menu screen.
2. Press  ▲▼ to select “Setup” icon.
3.  Press OK to display the Setup menu.
4. Press  ▲▼ to select “Language”.
EZ Sync
  Picture
  Audio Timer
  Lock Memory card
Setup
Menu
EZ Sync  Picture
  Audio Timer
  Lock Memory card
Setup
Menu
5.  Press OK to display the Language menu.
6. Press  ◄► to select “English,” “Español” or 
“Français”.
7.  Press...

27
Basic Operation
6. Press ▲▼ to select “ANT in”.
7. Press  ◄► to select “Antenna” or “Cable”.
8. Press  ▲▼ to select “Auto”.
9.  Press OK to display the Auto program menu.
10. Press  ▲▼ to select “All channels”, “Analog 
only”, or “Digital only”.
11. Press OK to start scan.
12. After Auto program is complete, the unit will  return to Manual program mode. To place 
the channels that were located by auto scan 
in memory, move the cursor to “Apply” and 
press OK. (p. 27-28)
If OK is not pressed after...

28
8. Press ◄► to select “Edit”.
9.  Press OK to enter the edit mode.
10. Press  ▲▼ to select the desired preset 
channel line.
11. Press  ◄► to select edit area (“Channel,” 
“Caption,” “Favorite,” “Add”).
Edit (Caption)
When a preset Caption has been entered.
1.  Press OK to display the Caption select  menu.
2. Press  ▲▼ to select “Caption”.
3. Press  ◄► to select Broadcast station.
4. Press  ▲▼ to select “Apply”.
5.  Press OK to enter the Caption.
When selecting a desired Caption manually.
1.  Press OK...

29
Basic Operation
 Selecting Input Mode
Procedure
1.  Press TV/VIDEO to display the Input select menu.
2.  Press corresponding NUMBER keys to select  the input of your choice. Or, press  ▲▼ to 
select the input of your choice, then press 
OK.
If, during selection, no action is taken for several seconds, 
the Input selection menu is exited and the current input is 
automatically selected.
•
 TV
Component 1
 Component 2
 HDMI 1
 HDMI 2
 HDMI 3
 Video 1
 Video 2
 Video 3
 PC
1
2
3
4
5
6
7
8
9
0
Input...

30
 Channel and Program Tuning
Channel and Program tuning in digital television differs 
from conventional television. With  DTV, many programs 
can exist within a single 6 MHz channel. These channels 
behave as sub-channels within a single channel. When 
tuning to a digital channel, the unit will also tune to a 
program and will indicate the channel and program in the 
on-screen Channel Banner display.
In order to select channels properly, Auto program must 
be performed. (p. 26-27)
Follow the procedure...