Panasonic LCD Projector Pt Vw355 Operating Instructions

FA Q
Please refer to the following items if you have problems with the wirele\
ss LAN connection.
The wireless LAN connection is interrupted suddenly.
 fThe picture may disappear or freeze depending on the radio wave environment. In such cases, please try the following measures. - Please make the wireless LAN connection device close to the projector. -  Place away from devices that can emit electromagnetic radiation, such as microwave ovens, game machines. Do not use these devices if you are still unable...

Others
 fDepending on your Intel® WiDi / Intel® Pro WiDi / Miracast compatible device, the confirmation screen of the reconnection that is the connection name "from UNKNOWN" will be displayed. At this time, please select "CANCEL" to cancel reconnect.
 fDepending on your Intel® WiDi / Intel® Pro WiDi / Miracast compatible device, it may be required to remove the profile during connecting. In that case, please remove the device according to t\
he instructions.
 fDepending on your Intel®...

Chapter 7   Appendix
This chapter describes specifications and after-sales service for the projector.
ENGLISH - 133  

Technical Information
PJLink protocol
The network function of the projector supports PJLink class 1, and the PJLink protocol can be used to perform projector setting 
and projector status query operations from a computer.
Control commands 
The following table lists the PJLink protocol commands that can be used to control the projector.
 fx characters in tables are non-specific characters.
CommandControl detailsParameter / return stringRemark
POWRPower supply control0
1
Standby
Power on
POWR ?Power supply...

Control commands via LAN
When WEB Control administrator rights password is set (Protect mode)
Connection method 
1) Obtain the IP address and port number (Initial set value = 1 024) of the projector \
and make a request 
for connection to the projector.
 fAcquire the IP address from the menu screen of the projector, and the port number from the WEB control page.
IP address :Obtain from MAIN MENU → [NETWORK/USB] → [STATUS]
Port No. :Acquire from the WEB control → [Detailed set up] → [Port set up] page
2)...

When WEB Control administrator rights password is not set (Non-protect \
mode)
Connection method 
1) Obtain the IP address and port number (Initial set value = 1 024) of the projector \
and make a request 
for connection to the projector.
 fAcquire the IP address from the menu screen of the projector, and the port number from the WEB control page.
IP address :Obtain from main menu → [NETWORK/USB] → [STATUS]
Port No. :Acquire from the WEB control → [Detailed set up] → [Port set up] page
2) There is a...

Serial terminal
The serial connector which is on the connector panel of the projector conforms to the RS-232C interface specification, so that 
the projector can be controlled by a personal computer which is connecte\
d to this connector.
Connection
Connecting terminals on projectorD-Sub 9-pin (female) Computer
Communication cable (straight)
D-Sub 9-pin (male)
Pin assignments and signal names
D-Sub 9-pin (female)
Outside viewPin No.Signal nameContents
—NC
TXDTransmitted data
RXDReceived data
—NC...

Basic format
Transmission from the computer starts with STX, then the ID, command, parameter, and ETX are sent in this order. Add 
parameters according to the details of control.
STXAD I1I2 ;C1C2 C3 : P1 P2Pn ETX
Basic format (with sub command)
S1S2S3S4S5 EP1P2P3P4P5P6
STX AD I1I2 ;C1C2C3 :  ETX
Same as basic format
Sub command (5 bytes) Operation (1 byte)
“=” (Value specified using parameter is set)Parameter (6 bytes)*
Symbol “+” or “
-” (1 byte) and set value or ad
-
justment value (5 bytes)
* When...

Cable specifications
[When connected to a computer] 
Projector
( terminal)
1NCNC1
Computer
(DTE specifications)
22334NCNC4556NCNC677889NCNC9
Control commands
When controlling the projector from a computer, the following commands are available.
 rProjector control command
CommandControl contentsParameter / return stringRemarks
PONPower on―To check if the power is on, use the “Power 
query” command.POFPower off
IISINPUT selection
VID
SVD
RG1
RG2
HD1
NWP
PA 1
MC1
MV1
VIDEO
S-VIDEO
RGB1
RGB2
HDMI
NETWORK...

Two window display combination list
Sub Window
COMPUTER1COMPUTER2
HDMIVIDEOS-VIDEO
Main WindowRGBYCBCR/YPBPRRGB
COMPUTER1RGB―――l――
YCBCR/YPBPR―――l――
COMPUTER2RGB―――l――
HDMIlll―ll
VIDEO―――l――
S-VIDEO―――l――
 l : Picture in Picture combinations are enabled.
 ―: Picture in Picture combinations are disabled.
Note
 f[MEMORY VIEWER], [MIRRORING] and [Panasonic APPLICATION] do not support two window display function.
 fWhen setting the movie-based signal 1080/24p, 1080/24sF,1080/25p, 1080/30p, 1080/50p or...