Panasonic LCD Projector Pt Vw350zu Pt Vx420zu Operating Instructions

Contents of mail sent 
Example of E-mail sent when E-mail is set
Mail with the contents shown below is sent when the e-mail settings have\
 been established.
=== Panasonic projector report(CONFIGURE) ===
Projector Type          : PT-VW350
Serial No               : 000000000
-----  E-mail setup data -----
TEMPERATURE WARNING SETUP 
MINIMUM TIME            at [ 60] minutes interval 
INTAKE AIR TEMPERATURE  Over [ 32degC / 89degF ] 
ERROR                   [ OFF ] 
LAMP RUNTIME            [ OFF ]   at...

Example of E-mail sent for an error
Mail with the contents shown below is sent when an error has occurred.
=== Panasonic projector report(ERROR) ===
Projector Type          : PT-VW350
Serial No               : 000000000
-----  check system -----
FAN                           [   OK   ]
INTAKE AIR TEMPERATURE        [   OK   ]
EXHAUST AIR  TEMPERATURE       [   OK   ]
OPTICS MODULE TEMPERATURE     [   OK   ]
LAMP REMAIN TIME              [   OK   ]
LAMP STATUS                   [   OK   ]
APERTURE...

[ECO management set up] page
You can make settings for the ECO management function of the projector.
Click [Detailed set up] → [ECO management set up].
1 [LAMP POWER]
Selects the [LAMP POWER] setting.
2  [AUTO POWER SAVE]
Select [ON] to set [AMBIENT LIGHT DETECTION], 
[SIGNAL DETECTION], and [AV MUTE DETECTION].
3  [AMBIENT LIGHT DETECTION]
Enable ([ON])/disable ([OFF]) the ambient light 
detection function. 
4  [SIGNAL DETECTION]
Enable ([ON])/disable ([OFF]) the signal detection 
function. 5 
[AV MUTE...

[Administrator] account
1 [Account : Administrator]
Displays the account to change. 
2  [Current] [User name]
Enter the user name before the change.
3  [Current] [Password]
Enter the current password.
4  [New] [User name]
Enter the desired new user name.   
(Up to 16 characters in single byte) 5 
[New] [Password]
Enter the desired new password.   
(Up to 16 characters in single byte)
6  [New] [Password (Retype)]
Enter the desired new password again.
7  [OK]
Determines the change of password.
[User]...

1 [Old  Password]
Enter the current password.
2  [New Password]
Enter the desired new password. (Up to 16 characters 
in single byte) 3 
[Retype]
Enter the desired new password again.
4  [OK]
Determines the change of password.
Note
 
f To change the account of the administrator, you must enter the [User name] and [Password] in [Current].
[Crestron Connected(TM)]  page 
The projector can be monitored/controlled with 
Crestron Connected™.
To start the Crestron Connected™  control page from the web control...

1 [Control System]
Set the information required for communicating with the
controller to be connected with the projector.
2  [User Password]
Set the user rights password for the Crestron 
Connected™  control page.
3  [Admin Password]
Set the administrator rights password for the  Crestron 
Connected™  control page. 4 
Network status
Displays the settings of wired LAN.
[DHCP]
Displays the current setting.
[IpAddress]
Displays the current setting.
[SubnetMask]
Displays the current setting....

Chapter 5   Maintenance
This chapter describes methods of inspection when there are problems, ma\
intenance, and 
replacement of the units.
ENGLISH - 97  

Lamp and Warning Indicators
When an indicator lights up
If a problem should occur inside the projector, the lamp indicator  and the warning indicator  will inform 
you by lighting or blinking. Check the status of the indicators and remedy the indicated problems as follows.
Attention
 
f Before you take a remedial measure, follow the procedure of switching the power of f indicated in “Powering Off the 
projector”. (x page 39)
Lamp indicator
Indicator Lighting in red. Blinking in red.
Status Time to...

Maintenance/replacement
Before performing maintenance/replacement
 
f When you perform maintenance or replacement of the parts, make sure to turn of f the power and disconnect the power plug 
from the wall outlet. (x pages 35, 39)
 
f Be sure to observe the procedure “ Powering Off the projector” (x page 39) when performing power supply operation.
Maintenance
Outer Case
Wipe off dirt and dust using a soft dry cloth.
 
f If the dirt is persistent, soak the cloth with water and wring it thorou\
ghly before...

Attaching the air filter unit
1) Attach the unused air filter unit to the projector.
 
f Hold the air filter unit that the tab is in up-left side in the figure, put the right side in the figure first, and press the tab side 
until make a click sound.
 
f Please press the tab of the air filter unit other than the pleated filter during installation.
2)  Install the air filter cover.
 
f Perform Step 1) in “Removing the air filter unit” ( x page 99) in the reverse order to close the air filter cover and...