Panasonic LCD Projector Pt Vw350zu Pt Vx420zu Operating Instructions

[PICTURE] menu
On the menu screen, select [PICTURE] from the main menu, and select an i\
tem from the sub-menu.
Refer to "Navigating through the menu" (x page 47) for the operation of the menu screen.
After selecting the item, press asqw  to set.
[PICTURE MODE]
You can switch to the desired picture mode suitable for the image source and the environment in which the projector is used.
1) Press as to select [PICTURE MODE]. 
2)  Press qw or the  button.
 
f The [PICTURE MODE] individual adjustment...

[BRIGHTNESS]
You can adjust the dark (black) part of the projected image.
1) Press as to select [BRIGHTNESS].
2)  Press qw or the  button.
 
f The [BRIGHTNESS] individual adjustment screen is displayed.
3)  Press qw to adjust the level.
Operation Adjustment Adjustment range
Press the ► button. Increases the brightness of the dark (black) parts of the screen.
-32 ~ +32
Press the ◄ button. Reduces the brightness of the dark (black) parts of the screen.
[COLOR]
(Only for movie-based signal input)
You can...

[COLOR TEMPERATURE]
You can switch the color temperature if the white areas of the projected image are bluish or reddish.
1) Press as to select [COLOR TEMPERATURE].
2)  Press qw or the  button.
 
f The [COLOR TEMPERATURE] individual adjustment screen is displayed.
3)  Press qw to switch the item.
 
f The items will switch each time you press the button.
[DEFAULT] Factory default setting.
[HIGH] Becomes a bluish image. Select this when the white areas of the projecte\
d image are reddish.
[LOW] Becomes a...

3) Press qw to switch the item.
 
f The items will switch each time you press the button.
[AUTO] Enables auto correction of [DAYLIGHT VIEW]. The brightness of the room is detected by the luminance 
sensor, and the vividness of the image is automatically corrected.  
[ON] Enables [DAYLIGHT VIEW].
[OFF] Disables [DAYLIGHT VIEW].
Note
 
f [DAYLIGHT VIEW] cannot be set to [AUTO] when the [PROJECTOR SETUP] menu → [PROJECTION METHOD] is set to 
[REAR/DESK] or [REAR/CEILING].
 
f The [AUTO] mode may not...

[RGB/YPBPR]/[RGB/YCBCR]
Set it to [AUTO] normally. If images are not displayed correctly when this is set to [AUTO], set either [RGB], [YCBCR] or [YPBPR] 
in accordance with the input signal.
1)  Press as to select [RGB/YPBPR] or [RGB/YCBCR].
2)  Press qw or the  button.
 
f The [RGB/YPBPR] or [RGB/YCBCR] individual adjustment screen is displayed.
3)  Press qw to switch the item.
 
f The items will switch each time you press the button.
[AUTO] The sync signal automatically selects the signal [RGB]/...

[POSITION] menu
On the menu screen, select [POSITION] from the main menu, and select an \
item from the sub-menu.
Refer to "Navigating through the menu" (x page 47) for the operation of the menu screen.
 
f After selecting the item, press asqw to set.
[REALTIME KEYSTONE]
The projector can correct the vertical trapezoidal distortion automatically when the projector is installed tilted.
1)  Press as to select [REALTIME KEYSTONE].
2)  Press qw or the  button.
 
f [REALTIME KEYSTONE] individual...

4) Press the  button.
 
f The [KEYSTONE] individual adjustment screen is displayed.
5)  Press asqw to adjust the item.
Items Operation AdjustmentAdjustment range
[H] Press the w button.
Adjusts the right of 
the keystone.
-60 ~ +60
Press the q button. Adjusts the left of the 
keystone.
[V] Press the a button.
Adjusts the upper of 
the keystone.
-80 ~ +80
Press the s button. Adjusts the bottom of 
the keystone.
[CORNER CORRECTION]
1)  Press as to select [KEYSTONE].
2)  Press the  button.
 
f The...

[SHIFT]
(Only for computer signal input)
Move the image position vertically or horizontally if the image position projected on the screen is shifted even when the relative 
position of the projector and the screen is installed correctly.
1) Press as to select [SHIFT].
2)  Press the  button.
 
f The [SHIFT] screen is displayed.
3)  Press asqw to adjust the position.
Orientation Operation Adjustment
Vertical (up and down) 
adjustment. Press the a button.
The image position moves up.
Press the s button.The...

3) Press qw to adjust the value.
 
f The adjustment values are [-16] to [+16]. Adjust so that the amount of interference is at a minimum.
Note
 
f Certain signals may not be adjustable.
 
f Optimal value may not be achieved if the output from the input computer is unstable.
 
f To project a signal with dot clock frequency with 162 MHz or higher, noise may not disappear even if [CLOCK PHASE] is 
adjusted.
 
f [CLOCK PHASE] cannot be adjusted when a digital signal is input.  
[OVER SCAN]
Use this function...

Note
 
f The image size may be switched abnormally when [AUTO] is selected, please set to [NORMAL] or [WIDE] according to the 
input signal.
 
f Some size modes are not available for certain types of input signals. 
 
f If an aspect ratio which is different from the aspect ratio for the input signals is selected, the imag\
es will appear differently 
from the originals. Be careful of this when selecting the aspect ratio.
 
f If using the projector in places such as cafes or hotels to display prog\
rams...