Panasonic LCD Projector PT-ST10U Operating Instructions

Settings
ENGLISH  31
Menu operation (continued)
 
▌CLOCK PHASE
If you require further adjustment for the same reason as 
the DOT CLOCK adjustment, you can further adjust the 
timing of the clock. (For RGB/YP
BPR input signal only)
Press ◄► buttons to adjust.
NOTE:
If the projecting signal’s dot clock frequency is higher than 
• 
162 MHz, adjusting  DOT CLOCK or CLOCK PHASE may 
not make any difference. Refer to “LIST OF COMPATIBLE 
SIGNALS”. (
 page 50 )
 
▌OVER SCAN
Use this function when characters...

Settings
32  ENGLISH
Menu operation (continued)
V FIT
Wide input signal*2   projection without changing the 
aspect ratio uses all the panel pixels in the vertical 
direction to crop the right and left of the image.
Input signal: 1 080/60i
Image:
HV FIT
The image is projected all over the panel pixels 
(screen). The input signal is projected at the aspect 
ratio of the panel screen.
Input signal: 1 080/60i
Image:
S4:3
Standard input signal*1    the input signal will be sized 
down 75% and projected....

Settings
ENGLISH  33
Menu operation (continued)
LANGUAGE MENU
Select the required language.
Remote controlControl panel
MENURETURN
EN TE R
FR EE ZEA V
M UTE
C O M PUTERVID EO
D EFA ULT
FUNCT IO NWIN .INDE X-
M ENU
EN TE R
MENUFUNCTION
ENTER INPUT
SELECTLAMP
STANDBY 
(R)ON (G)
TEMPMENU
ENTER
M
ENURETURN
EN TE R
FR EE ZEA V
M UTE
C O M PUTERVID EO
D EFA ULT
FUNCT IO NWIN .INDE X-
M ENU
EN TE R
MENUFUNCTION
ENTER INPUT
SELECTLAMP
STANDBY 
(R)ON (G)
TEMPMENU
ENTER
PICTURE
POSITION
DISPLA
Y OPTION
PROJECT OR...

Settings
34  ENGLISH
Menu operation (continued)
Computer connection guide
You can switch the output signals from COMPUTER1/
COMPUTER2 terminal by pressing the following 
computer command keys.
Manufacturer Image output 
selection 
command
Panasonic
NEC
 + 
SAMSUNG
HP + 
acer
SHARP
TOSHIBA
 + 
NOTE:
The command keys depend on the manufacturers.  
• 
For detailed information, please refer to the instructions 
provided with the computers.
If you want to turn off the computer connection guide, select 
•...

Settings
ENGLISH  35
Menu operation (continued)
Editing the original text
1Press [] to select TEXT and then press 
[ENTER].
2Press [ ] to select the desired line and then 
press [ENTER].
You can input and edit the text for the first line in 
TEXT1 and the text for the second line in  TEXT2.
STAR TUP  LOGO
TEXT2 OK CANCEL
TEXT1
RETURN
ENTER
SELECT
3Press [
 ] to select the desired character 
and then press [ENTER].
To delete all the input characters, move the cursor 
to ALL DELETE and then press...

Settings
36  ENGLISH
Menu operation (continued)
 
▌WIDE MODE
Set this mode when projecting wide signals (16:9, 
16:10, 15:9).
Change setting 
 Changesetting Change
setting Change setting
AUTO
Automatic setting
OFF For 4:3 signals
ON For WIDE signals
 
▌SXGA MODE
Set this mode when an  SXGA signal is input and the 
projected image is trimmed.
Change setting 
 Changesetting Change
setting Change setting
SXGA
For normal projection
SXGA+ For projection when image is cropped
 
▌OTHER FUNCTIONS
You can...

Settings
ENGLISH  37
Menu operation (continued)
 
▌NO SIGNAL SHUT-OFF
If no image signal is input for the time set using the 
timer, the projector will automatically enter into standby 
mode.
Change setting 
 Changesetting Change
setting Change setting
DISABLE
NO SIGNAL SHUT-OFF  is disabled
15 – 60  MIN. Timer can be set at a 5-minute intervals
 
▌INITIAL START UP
You can set the starting method when the power plug is 
connected to wall outlet.
Change setting 
 Changesetting Change
setting Change...

Settings
38  ENGLISH
Menu operation (continued)
 
▌LAMP RUNTIME
You can check how long the lamp has been used.
NOTE:
LAMP RUNTIME
•   is important for lamp replacement timing. 
See “REPLACE THE LAMP UNIT”. (
 page 45 )
Check the lamp unit replacement time. 
•  (
 page 45)
If the lamp runtime has reached 3 800 hours, the red and 
• 
gray marks appear alternately to notify you of the lamp 
replacement time.
The lamp life varies depending on the usage condition 
• 
(number of power-on times, etc.)....

Settings
ENGLISH  39
 
▌TEST PATTERN
You can use the 7 different test patterns to adjust the 
focus of the image.
E N TERTo display the test pattern.
   
Change pattern  Change
setting Change
setting Change pattern
Press [MENU] or [RETURN] to return to the 
PROJECTOR SETUP menu, or press repeatedly to 
escape the menu mode.
NOTE:
The initial screen is an all white pattern. Only when 
•  TEST 
PATTERN is assigned to the  [FUNCTION] button, the lattice 
pattern will be displayed as the initial screen....

Settings
40  ENGLISH
SECURITY MENU
Remote controlControl panel
MENURETURN
ENT ER
FR EE ZEA V
M UTE
C O M PUTERVIDE O
D EFA ULT
FUNCTIO NWIN.INDEX-
M ENU
ENT ER
D EFA ULT
MENUFUNCTION
ENTER INPUT
SELECTLAMP
STANDBY 
(R)ON (G)
TEMPMENU
ENTER
M
ENURETURN
ENT ER
FR EE ZEA V
M UTE
C O M PUTERVIDE O
D EFA ULT
FUNCTIO NWIN.INDEX-
M ENU
ENT ER
D EFA ULT
MENUFUNCTION
ENTER INPUT
SELECTLAMP
STANDBY 
(R)ON (G)
TEMPMENU
ENTER
Set the selected item with [
].
When you use SECURITY menu for the first time, you 
will...