Panasonic LCD Projector PT-ST10U Operating Instructions

Preparation
ENGLISH  11
Control Panel / Indicators
③
④
⑤
LAMP
S
TANDB Y 
(R)O N(G)
TEMPMENUFUNCTION
ENTER INPUT
SELECTNCTETI
R
⑦ ⑧ ⑨
⑥
①
②
① Indicate the power supply’s status.   
(   page 19
)
② Indicate the lamp unit’s status. 
(
  page 43
)
③ Indicate the temperature’s status. 
(
  page 43
)
④ Ambient Luminance sensor (ALS).
⑤ Display the Main menu. ⑥
Navigate through the menus.
Confirm selection.
⑦ Create shortcut assigned to certain selected 
function. (
 page 25, 38)
⑧ Switch the input...

Preparation
12  ENGLISH
Details of your projector (continued)
①
②
③
④
⑤ ⑥⑦
⑧
⑨
①
Terminals
② Air filter compartment  (
 page 44
)
③ Air intake port
④ AC IN
Connect the power cord to supply electric power to 
the projector. (
 page 18
)
⑤ Leg adjuster
To adjust the projection angle.  (
  page 22
) ⑥
Air intake port
⑦ Burglar hook port
Attach a commercial burglar prevention cable.
⑧ Lamp unit compartment (
 page 46
)
⑨ Remote control signal receptor
① Connect to a network cable.  
(See “Network...

Preparation
ENGLISH  13
Details of your projector (continued)
PROJECTOR’S REMOTE CONTROL
Top and rear view
Remote controlsignal emitters
Installing/removing batteries
Press the tab and lift up the 
cover. Insert the batteries according to the 
polarity diagram indicated inside or 
remove.
Remove the batteries in the reverse 
order to setting.
Use only manganese batteries.
Front view
AUTO
SETUP
M ENURETURN
ENT ER
FR EE ZEA V
M UTE
C O M PUTERVIDE O
D EFA ULT
FUNCTIO NWIN.INDEX-
DIGIT AL ZOOM
VOLUME
①
⑤...

Getting started
14  ENGLISH
Set up your projector
SCREEN SIZE AND THROW DISTANCE
You can calculate and define the throw distance as follows.
69.2 mm
LSW
SD
SW
SH
SH
H
L
Screen
Screen
Projected image
(All measurements below are approximate and may differ slightly from the actual measurements.)
Projection size
For 4:3 aspect ratio For 16:9 aspect ratio
Screen diagonal (SD) Throw distance (L)Settable height (H)Throw distance (L)  Settable height (H)
1.52 m (60") 0.60 m (2' 0")0.05 m (0'...

Getting started
ENGLISH  15
Set up your projector (continued)
PROJECTION METHOD
See “INSTALLATION” on page 37 to select the projection method.
Put it on a desk or floor and project from the front
 
„ Mount it on the ceiling and project from the front
 
„
Menu Method
INSTALLATION FRONT/DESKMenu Method
INSTALLATION FRONT/CEILING
Put it on a desk or floor and project from the rear
 
„
(Use translucent screen) Mount it on the ceiling and project from the rear
 
„
(Use translucent...

Getting started
16  ENGLISH
Connections
Preparations
Read and follow the operating instructions of each peripheral device and\
 turn the peripheral devices off prior to 
• 
making any connections.
Prepare the selected peripheral devices with the connection cables that \
correspond to the projector’s terminals.
• 
All peripheral devices and cables used for the connections are sold sepa\
rately unless indicated otherwise.
• 
If the input signal is affected by signal jitter, the projected image may have...

Getting started
ENGLISH  17
Connections (continued)
NOTE:
For the network connection between the projector and computers, see “\
Network Operation Manual” in the CD-ROM provided.
• 
Only the RGB signal cable (1 piece) is attached. If any other cables a\
re necessary, purchase them from the market.
• 
LANSERIALCOMPUTER 1 IN
S-VIDEOOIN
VIDEO INAUDIO IN12
AUDIO
COMPUTER 2 IN
LANSERIALCOMPUTER 1 IN
AUDIO IN1
AUDIO
COMPUTER 2 IN
AUDIO OUT
Audio system
Computer
Computer
Computer
(Controlling a projector)...

Basic operations
18  ENGLISH
Turn the projector ON or OFF
POWER CORD
Fix the provided “power cord secure lock” to the power cord on the\
 projector to prevent the cord from 
coming off.
For details, see “Precautions with regard to safety”. (
 pages 5 to 9)
1Push the connector all the way into the AC 
IN terminal ensuring that the shape of the 
connector matches that of the terminal.
2Align the side of the “power cord secure lock” 
with the side of the “Rail guide” of the AC IN 
terminal and slide it...

Basic operations
ENGLISH  19
Turn the projector ON or OFF (continued) 
POWER INDICATOR
LAMP
STANDBY 
(R)ON (G)
TEMP
POWER indicator

 shows status of the projector’s power
When the TEMP indicator flashes, the  POWER indicator 
lights red and you cannot turn the projector on.
POWER indicator status
Indicator status Status
No illumination or flashing No power is supplied and the internal cooling fan is not operating.
Red Lit
The power is turned off (when STANDBY MODE is set to 
ECO).
If [ POWER] button...

Basic operations
20  ENGLISH
Turn the projector ON or OFF (continued)
TURN THE PROJECTOR ON
STANDBY (R)ON (G)
2)
Before switching on the projector, make sure the mains lead and all the other devices are connected corre\
ctly. 
(
  page 16
)
1Connect the power cord.  (
  page 18
)
After a while the “power indicator” lights or 
flashes in red.
2Press the POWER button.
POWER
•   indicator flashes green several times  
before it lights up and the  STARTUP LOGO is 
displayed.  See STARTUP LOGO in DISPLAY...