Panasonic LCD Projector PT-L300U PT-L200U Operating Instructions

11
Preparation
10
About the SD memory card slot
Make sure that there are no foreign objects inside the slot when inserting an
optional SD memory card. Failure to observe it may damage the card and
the slot.
About the screen
If the screen you are using is dirty, damaged or discolored, attractive
projections cannot be obtained. Do not apply any volatile substances to the
screen, and do not let it become dirty or damaged.
About the lamp
The lamp may need to be replaced earlier due to variables such as a...

13
Preparation
12
#Air outlet port
Do not cover this port.WARNINGDo not bring your hands or other
objects close to the air outlet
port.
BHeated air comes out of the air
outlet port. Do not bring your
hands or face, or objects which
cannot withstand heat close to
this port, otherwise burns or
damage could result.
$Connector panel 
(page 16)
%Power input socket (AC IN)
(page 22)
The accessory power cord is
connected here.
Do not use any power cord other
than the accessory power cord.
&Lamp unit holder...

13
Preparation
12
#Air outlet port
Do not cover this port.WARNINGDo not bring your hands or other
objects close to the air outlet
port.
BHeated air comes out of the air
outlet port. Do not bring your
hands or face, or objects which
cannot withstand heat close to
this port, otherwise burns or
damage could result.
$Connector panel 
(page 16)
%Power input socket (AC IN)
(page 22)
The accessory power cord is
connected here.
Do not use any power cord other
than the accessory power cord.
&Lamp unit holder...

15
Preparation
14
+KEYSTONE buttons
(pages 28 and 29)
This button is used to correct
keystone distortion of the
projected image when the
projector position is tilted upward
or downward.
,NORMAL button 
(page 27)
This button is used to reset the
projector adjustment values to the
factory default settings.
-ASPECT button 
(page 30)
This button is used for aspect
adjustment (vertical and
horizontal proportions).
.MUTE button
(page 33)
This button momentarily stops
output of the projector’s built-in...

15
Preparation
14
+KEYSTONE buttons
(pages 28 and 29)
This button is used to correct
keystone distortion of the
projected image when the
projector position is tilted upward
or downward.
,NORMAL button 
(page 27)
This button is used to reset the
projector adjustment values to the
factory default settings.
-ASPECT button 
(page 30)
This button is used for aspect
adjustment (vertical and
horizontal proportions).
.MUTE button
(page 33)
This button momentarily stops
output of the projector’s built-in...

17
Preparation
16

#
$ %& '(
$% '
#(
#AUDIO L-R input jacks 
(page 18)
$VIDEO input jack 
(page 18)
This jack is used to input video
signals from a video equipment
such as a video deck.
%S2 VIDEO input connector 
(page 18 and 30)
This connector is used to input
signals from an S-VIDEO-
compatible equipment such as a
video deck. The connector is
compatible with S2 and S1
signals, and projector aspect is
automatically adjusted according
to the type of signal received.&DVI-D IN connector
(page 20)...

17
Preparation
16

#
$ %& '(
$% '
#(
#AUDIO L-R input jacks 
(page 18)
$VIDEO input jack 
(page 18)
This jack is used to input video
signals from a video equipment
such as a video deck.
%S2 VIDEO input connector 
(page 18 and 30)
This connector is used to input
signals from an S-VIDEO-
compatible equipment such as a
video deck. The connector is
compatible with S2 and S1
signals, and projector aspect is
automatically adjusted according
to the type of signal received.&DVI-D IN connector
(page 20)...

1819
Preparation
Example of connecting to video equipment
DVD player
Video deck
NOTE:
BOnly one audio system circuit is available for the AUDIO IN L-R jacks, so if
you wish to change the audio input source, you will need to remove and
insert the appropriate plugs. 
ConnectionsNotes on connectionsBRead the instruction manual for each system component carefully before
connecting it.
BTurn off the power supply for all components before making any
connections.
BIf the cables necessary for connecting a...

1819
Preparation
Example of connecting to video equipment
DVD player
Video deck
NOTE:
BOnly one audio system circuit is available for the AUDIO IN L-R jacks, so if
you wish to change the audio input source, you will need to remove and
insert the appropriate plugs. 
ConnectionsNotes on connectionsBRead the instruction manual for each system component carefully before
connecting it.
BTurn off the power supply for all components before making any
connections.
BIf the cables necessary for connecting a...

2021
Preparation
Setting-upProjection methodsThe projector can be set up so that any one of the following four projection
methods can be used. Select whichever projection method matches the
setting-up method. (The projection method can be set from the OPTION
menu. Refer to page 40 for details.)
FRONT/REARFRONT
REAR
(Factory default setting)
NOTE:
BYou will need to purchase the separate ceiling bracket (ET-PKE300) when
using the ceiling installation method.Projector positionThe projection range of this...