Panasonic Kx-tvs50, Kx-tvs80 Voice Processing System Installation Manual

1.3 SYSTEM BASICS
VOICE PROCESSING SYSTEM OVERVIEW
21
1.3.5 Specifications
1.3.6 Hardware
•
1 (KX-TVS50) or 2 (KX-TVS80) Flash Memory Card(s).
•
1 Optional Flash Memory Position for KX-TVS52 card
*1
•
2 Telephone Inputs (RJ11C)
•
1 RS-232C Connector
•
1 DIP Switch (4-bit)
1.3.7 Flash Memory Expansion Capabilities*1
Expansion of the flash memory capacity requires an optional expansion memory card (KX-
TVS52). The KX-TVS50 initially has 2-h memory. The KX-TVS52 increases the capacity by 
2 h.
1.3.8...

1.3 SYSTEM BASICS
22VOICE PROCESSING SYSTEM OVERVIEW
One port may not support an Automated Attendant configuration with 5 CO lines. The 
following recommendations for Automated Attendant ports may have to be modified for heavy 
traffic.Ta b l e  3  
CO Lines Port
1-6 1
7-12 2
Ta b l e  4  
CO Lines Port
1-4 1
5-8 2 

1.4 DIGITAL INTEGRATION
VOICE PROCESSING SYSTEM OVERVIEW
23
1.4 DIGITAL INTEGRATION
1.4.1 General
There are 2 types of Digital Integration: APT Integration and DPT Integration.
APT Integration is available when the KX-TVS50/80 is connected to a KX-TA624. DPT 
Integration is available when the KX-TVS50/80 is connected to a KX-TD digital PBX.
1.4.2 APT Integration
To the Panasonic KX-TA624, the VPS ports look like proprietary telephones. The PBX thinks 
that the VPS is a proprietary telephone, and the VPS...

1.4 DIGITAL INTEGRATION
24VOICE PROCESSING SYSTEM OVERVIEW
TVS50/80). To communicate between the VPS and the PBX through DPT Integration, the PBX 
and VPS must be programmed to work together.
1.4.5 Connection Example — DPT Integration
For example, you can connect jack 15 of the KX-TD1232 to Port 1 of the VPS with a 4-wire 
connection (see diagram below). This connection creates 2 Voice Mail extensions and can 
simultaneously answer 2 calls. This means that a fully-configured 2-port system requires only...

INSTALLATION25
Section 2
INSTALLATION 

2.1 SAFETY PRECAUTIONS
26INSTALLATION
2.1 SAFETY PRECAUTIONS
Please read the following precautions before installing the VPS.
2.1.1 Installation
The VPS needs to be installed on the wall. Improper placement of the system may result in 
malfunction, noise, or discoloration. Avoid installing the VPS in the following places:
•
in direct sunlight; in hot, cold, or humid places
•
in new areas where there are thermal springs, etc. (where sulfuric gas may damage the 
equipment or contacts).
•
where shocks or...

2.2 UNPACKING
INSTALLATION
27
2.2 UNPACKING
Unpack the box and check the items below.
Ta b l e  5  
Main Unit 1
AC Cord 1
Screws (Wall Mounting) 3
Washers (Wall Mounting) 3 

2.3 MOUNTING THE VPS ON A WOODEN WALL
28INSTALLATION
2.3 MOUNTING THE VPS ON A WOODEN WALL
The wall where the VPS is to be mounted must be able to support the weight of the VPS. If 
screws other than the ones supplied are used, use the same-sized diameter screws as the 
enclosed ones.
1.Place the template included on the wall to mark the 3 screw positions.
2.Install the 3 screws (included accessories) into the wall.
3.Hook the unit on the screw heads.
Template
 










 
Wooden
Wall
Drive the...

2.4 FRAME GROUND CONNECTION
INSTALLATION
29
2.4 FRAME GROUND CONNECTION
IMPORTANT!!!
Connect the frame of the main unit to the ground.
1.Loosen the screw.
2.Insert the grounding wire.
3.Tighten the screw.
4.Connect the grounding wire to the ground.
In most of North America, the ground provided by the Third wire ground at the commercial 
or residential power outlet will be satisfactory. However, in some cases this ground may be 
installed incorrectly. Therefore, the following test procedure should be...

2.5 INSTALLATION STEPS
30INSTALLATION
2.5 INSTALLATION STEPS
The following is an overview of the standard installation process using APT/DPT Integration. 
When necessary, other sections in this manual have been referenced for more detailed 
descriptions or instructions.
1.Get a list of current users, their extension numbers, their departments, and the type of 
systems they use (mailbox, no mailbox, beeper, car phone...).
2.Assess your customers needs before setting up the system. You will save yourself...