Panasonic Kx Tgl430 Operating Instructions Manual

nFrom the phonebook:
1 MMENU N#268
2 Mb N:  “On ” a  M SELECT N
3 Mb N: Select  “Outgoing call ” to
monitor from outside.  a M ADD N
4 Mb N:  “Phonebook ” a  M SELECT N
5 Mb N: Select the phonebook entry.  a
M SAVE N
R “Baby monitor ” will be displayed.
Note:
R If you edit a phonebook entry which is
assigned for monitoring, the edited entry
does not transfer to the monitor.
n By entering phone numbers:
1 MMENU N#268
2 Mb N:  “On ” a  M SELECT N
3 Mb N: Select  “Outgoing call ” to
monitor from outside....

If you want to respond from your monitoring
phone, press #1 using tone dialing.
You can turn off the baby monitor feature
by pressing  #0.
Note:
R The unit disconnects the call automatically
after 2 minutes.
Other programming
Changing the handset name
The default handset name is  “Handset 1 ” to
“ Handset 6 ”. You can customize the name
of each handset (“Bob”, “Kitchen”, etc.). This is
useful when you make intercom calls between
handsets. To display the handset name in
standby mode, turn on the handset...

Using Caller ID serviceImportant:
R This unit is Caller ID compatible. To use
Caller ID features, you must subscribe to a
Caller ID service. Contact your phone
service provider for details.
Caller ID features
When an outside call is being received, the
caller information is displayed.
Caller information for the last 50 callers is
logged in the caller list from the most recent
call to the oldest.
RIf the unit cannot receive caller information,
the following is displayed:
–“Out of area ”: The caller dials...

Note:
RIf the entry has already been viewed or
answered, “
” is displayed.
Editing a caller’s phone number
You can edit a phone number in the caller list
by removing its area code and/or the long
distance code “1”.
1 ME N (Redial/CID)
R If the redial list is displayed, press  ME N
(Redial/CID) again to switch to the
caller list.
2 Mb N: Select the desired entry.  a M MENU N
3 Mb N:  “Edit ” a  M SELECT N
4 Press  MEDIT N repeatedly until the phone
number is shown in the desired format.
5 M
/Z N
Caller...

Answering system
The answering system can answer and record
calls for you when you are unavailable to
answer the phone.
You can also set the unit to play a greeting
message but not to record caller messages by
selecting “Greeting only ” as the recording
time setting (page 40).
Important:
R Make sure the unit’s date and time setting
is correct (page 12).
Memory capacity (including your
greeting message)
The total recording capacity is about 17
minutes. A maximum of 64 messages can be
recorded.
Note:...

1MMENU N#304
2 MYES N a  M OFF N
Playing back the greeting
message
1 MMENU N#303
2 To exit, press  MOFF N.
Listening to messages
Important:
R When using the base unit or handset to
listen to messages, the noise reduction
feature (page 16) is activated automatically
in spite of the setting (
 is not
displayed).
Using the base unit
When new messages have been recorded,
M
N  on the base unit flashes.
Press  MN (PLAY).
R During playback,  MN on the base unit
lights.
R If new messages have been recorded,...

KeyOperation
*6Reset to a pre-recorded
greeting message
*1 If pressed within the first 5 seconds of amessage, the previous message is
played.
*2 To resume playback: Mb N:  “Playback ” a  M SELECT N
*3 You can also erase as follows: MPAUSE N a  M b N:  “Erase ” a
M SELECT N a  M b N:  “Yes ” a  M SELECT N
Calling back (Caller ID subscribers
only)
1Press  MPAUSE N during playback.
2 Mb N:  “Call back ” a  M SELECT N
Editing the  number  before  calling  back
1 Press  MPAUSE N during playback.
2 Mb N:...

Turning on/off the new message alert
setting
1MMENU N#338
2 Mb N:  “On/Off ” a  M SELECT N
3 Mb N: Select the desired setting.  a
M SAVE N a  M OFF N
Editing the set phone number
1 MMENU N#338
2 Mb N: “ Notification  to ” a  M SELECT N
3 MMENU N a  M b N:  “Edit ” a  M SELECT N
4 Edit the name if necessary (16 characters
max.).  a M OK N
5 Edit the phone number if necessary (24
digits max.).  a M OK N a  M SELECT N a
M OFF N
Erasing the set phone number
1 MMENU N#338
2 Mb N: “ Notification  to ” a  M...

2Enter the desired 3-digit remote access
code.  a M SAVE N a  M OFF N
Deactivating remote operation
Press  * in step 2 on “Remote access code”,
page 38.
R The entered remote access code is deleted.
Using the answering system
remotely
1 Dial your phone number from a
touch-tone phone.
2 After the greeting message starts, enter
your remote access code.
3 Follow the voice guidance prompts as
necessary or control the unit using
remote commands (page 39).
4 When finished, hang up.
Voice guidance
nWhen the...

1MMENU N#310
2 Mb N: Select the desired setting.  a
M SAVE N a  M OFF N
Number of rings before the unit
answers a call
You can change the number of times the
phone rings  “Ring count ” before the unit
answers calls. You can select 2 to 7 rings, or
“ Toll saver ”.
The default setting is  “4 rings ”.
“ Toll saver ”: The unit’s answering system
answers at the end of the 2nd ring when new
messages have been recorded, or at the end
of the 5th ring when there are no new
messages. If you call your phone from...