Panasonic Kx Tge463 Operating Instructions Manual

							
Sub-menu 1Sub-menu 2SettingsCode
SettingsAuto connect*1Off
<
1 min >
3 min
5 min
10 min#63218
Cell area code *1–#63320
Cell line only
mode*1On
<
Off >#15719
Cell line select
–Handset
Cellphone 1 *5
Cellphone 2 *5#63420
Cell line select
–
Base unit *1
, *3<
Cellphone 1 >*5
Cellphone 2 *5#
G 634
Set PIN *1<
0000 >#61920
International
code *1–#11753
Country code *1–#118
Trunk prefix*1–#119
Main menu:  “
Set date & time ”
Sub-menu 1Sub-menu 2SettingsCode
Date and time*1––#10116
Memo alarmAlarm1–3<
Off >
Once
Daily
Weekly#72046
Time
adjustment *1, *10–<
Caller ID auto >
Manual#226–
Main menu:  “ Speed dial ”
OperationCode
Viewing the speed dial entry.#26136
For assistance, please visit http://shop.panasonic.com/support41
Programming

TGE46x47x(en)_1117_ver061.pdf   412015/11/17   15:14:14      
						

							
Main menu:  “Settings ”
Sub-menu 1Sub-menu 2SettingsCode
Ring adjustmentsRinger volume
– Handset *4Off
–6 #160–
Ringer volume
– Base unit *1,
 *4Off
–6 #G 160–
Ringer tone *4, *8, *11
(Handset)< Tone 1 >#161–
Interrupt tone
–Handset *12<
On >
Off#20125
Interrupt tone
– Base unit *1, *3,
 *12<
On >
Off# G 20129
Silent mode
– HandsetOn/Off
–On
– < Off>#23847
Start/End
– < 11:00 PM/
06:00 AM >#23747
Select group
Home
Cell 1
Cell 2
Group 4-9#24147
Silent mode
–Base unit *1, *3On/Off
–
On
– < Off>#G 23847
Start/End
– < 11:00 PM/
06:00 AM >#G 23747
Select group
Home
Cell 1
Cell 2
Group 4-9#G 24147
Set date & timeDate and time *1–#10116
Memo alarm
–
Alarm1–3
Once
Daily
Weekly#72046
Time
adjustment *1, *10<
Caller ID auto >
Manual#226–
42For assistance, please visit http://shop.panasonic.com/support
Programming

TGE46x47x(en)_1117_ver061.pdf   422015/11/17   15:14:15   
						

							
Sub-menu 1Sub-menu 2SettingsCode
Talking caller IDHandset
Off#16251
Base unit *1On
<
Off >#G 162
Key detector
setting *13
– 1:Add new device
(for  Detector1 )*14
– 2:Add new device
(for  Detector2 )
– 3:Add new device
(for  Detector3 )
– 4:Add new device
(for  Detector4 )Change name *1Detector1#6561–
Detector2*15#6562*15
Detector3 *15#6563*15
Detector4 *15#6564*15
Registration–#6571–
#6572*15
#6573*15
#6574*15
Deregistration–#6581–
#6582*15
#6583*15
#6584*15
Call block *1Block a single
number–#21732
Block range of
numbers–33
Block unknown CID
( CID : Caller ID)Block
#24033
One ring for
blocked call
No#17333
Speed dial––#26136
Cell locator––#24830
Record greeting *1––#30258
Voicemail*4Save VM access# *1
( VM : Voicemail)–#33165
VM tone detect *1<
On >
Off#33265
Message indicator–< On >
Off#34064
LCD contrast
(Display contrast)–Level 1–4 #145–
Handset name––#10449
Display name–On
< Off >#10549
For assistance, please visit http://shop.panasonic.com/support43
Programming

TGE46x47x(en)_1117_ver061.pdf   432015/11/17   15:14:15  
						

							
Sub-menu 1Sub-menu 2SettingsCode
Auto intercomHandsetOn
#27331
Base unit *1,
 *3On
<
Off >#G 273
Key tone–
Off#165–
Caller ID edit
(Caller ID number auto edit)–< On >
Off#21452
Auto talk *16–On
<
Off >#20022
Set tel line *4Set dial mode *1<
Tone >
Pulse#12016
Set flash time *1, *1780 ms
90 ms
100 ms
110 ms
160 ms
200 ms
250 ms
300 ms
400 ms
600 ms
<
700 ms >
900 ms#12123
Set line mode *1, *18A
 < B>#122–
Call sharing *1–<
On >
Off#19424, 29
RegistrationRegister handset–#13049
Deregistration *2–#13150
Power failure–<
Auto >
Off#15225
Change languageDisplay< English >
Español#11016
Announcement *1<
English >
Español#11216
Main menu:  “ Customer support ”
OperationCode
Displaying customer support Web address.#680–
44For assistance, please visit http://shop.panasonic.com/support
Programming

TGE46x47x(en)_1117_ver061.pdf   442015/11/17   15:14:15    
						

							
Main menu:  “Baby monitor ”
Sub-menu 1Sub-menu 2SettingsCode
On/Off–On
#26847
Sensitivity level–Low

High#26948
Main menu:  “Key detector ”*13
Sub-menu 1Sub-menu 2SettingsCode
Search––#655–
Battery check––
*1 If you program these settings using one of the units, you do not need to program the same
item using another unit.
*2 This menu is not displayed when scrolling through the display menus. It is only available in direct command code.
*3 KX-TGE470 series: page 4
*4 When the cellular line only mode is turned on, these menus are not displayed (page 19).
*5 After the Bluetooth device is paired, the device name is displayed.
*6 For CELL 1
*7 For CELL 2
*8 The preset melodies in this product ( “Tone 3 ” -  “Melody 10 ”) are used with permission of
© 2004 - 2013 Copyrights Vision Inc.
*9 The preset melodies in this product ( “Tone 1 ” and  “Tone 2 ”) are used with permission of
© 2013 Copyrights Vision Inc.
*10 This feature allows the unit to automatically adjust the date and time each time caller information including date and time is received.
To turn this feature on, select  “Caller ID auto ”. To turn this feature off, select
“ Manual ”. (Caller ID subscribers only)
To use this feature, set the date and time first (page 16).
*11 If you subscribe to a distinctive ring service (such as IDENTA-RING), select a tone (tone 1 or 2). If you select a melody, you cannot distinguish lines by their ringers.
*12 This tone lets you know when you receive an outside call while you are on another line or an intercom call. If you select  “On ”, the tone sounds 2 times.
*13 This setting is available when you have the key detector (KX-TGA20). Read the installation manual for more information on the key detector.
*14 For models with supplied key detectors, the display shows “ 1: Detector1 ”.
*15 If you register 2 or more key detectors.
*16 If you subscribe to a Caller ID service and want to view the caller’s information after lifting up the handset to answer a call, turn off this feature.
*17 The flash time depends on your telephone exchange or host PBX. Contact your PBX supplier if necessary. The setting should stay at  “700 ms ” unless pressing  MFLASH N fails to
pick up the waiting call.
For assistance, please visit http://shop.panasonic.com/support45
Programming

TGE46x47x(en)_1117_ver061.pdf   452015/11/17   15:14:15     
						

							
*18 Generally, the line mode setting should not be changed. This setting automatically maintainsreceiver volume at the proper level depending on the current telephone line condition. Set
the line mode to  “A ” if telephone line condition is not good.
Alarm
An alarm sounds at the set time for 1 minute
and is repeated 5 times at 5 minute intervals
(snooze function). A text memo can also be
displayed for the alarm. A total of 3 separate
alarm times can be programmed for each
handset. You can set one of 3 different alarm
options (once, daily, or weekly) for each alarm
time.
Important:
R Make sure the unit’s date and time setting
is correct (page 16).
1 MMENU N#720
2 Mb N: Select the desired alarm.  a
M SELECT N
3 Mb N: Select the desired alarm option.  a
M SELECT N
“Off ”
Turns alarm off. Go to step 10.
“ Once ”
An alarm sounds once at the set time.
“ Daily ”
An alarm sounds daily at the set time.
Go to step 5.
“ Weekly ”
Alarm sounds weekly at the set time(s).
4 Proceed with the operation according to
your selection in step 3.
nOnce:
Enter the desired month and date.  a
M OK N
n Weekly:
M b N: Select the desired day of the week
and press  MSELECT N.  a  M OK N
5 Set the desired time.
6 *: Select  “AM ” or  “PM ”.  a  M OK N
7 Enter a text memo (10 characters max.).
a M OK N
8 Mb N: Select the desired alarm tone.  a
M SELECT N
R We recommend selecting a different
ringer tone from the one used for
outside calls.
9 Mb N: Select the desired snooze setting.
a  M SAVE N
10 MSELECT N a  M OFF N
Note:
R Press  MSTOP N to stop the alarm completely.
R When the handset is in use, the alarm will
not sound until the handset is in standby
mode.
R Press any dial key or  MSNOOZE N to stop
the sound but keep the snooze function
activated.
R If you want to make an outside call when
the snooze function is activated, please
stop the snooze function before making the
call.
Silent mode
Silent mode allows you to select a period of
time during which the handset and/or base
unit will not ring for outside calls. This feature
is useful for time periods when you do not
want to be disturbed, for example, while
sleeping. Silent mode can be set for each unit.
Using the phonebook’s group feature
(page 35), you can also select groups of
callers whose calls override silent mode and
ring the unit (Caller ID subscribers only).
Important:
R Make sure the unit’s date and time setting
is correct (page 16).
R We recommend turning the base unit ringer
off (page 40, 42) in addition to turning the
silent  mode  on.  (KX-TGE460  series:  page  4)
46For assistance, please visit http://shop.panasonic.com/support
Programming

TGE46x47x(en)_1117_ver061.pdf   462015/11/17   15:14:15 
						

							
RIf you have set the alarm, the alarm sounds
even if the silent mode is turned on.
Turning silent mode on/off
1 For handset setting:  M MENU N#238
For base unit setting (using a
handset) *1
: M MENU N#*238
2 Mb N: Select the desired setting.  a
M SAVE N
R If you select  “Off ”, press  MOFF N to
exit.
3 Enter the desired hour and minute you
wish to start this feature.
4 *: Select  “AM ” or  “PM ”.  a  M OK N
5 Enter the desired hour and minute you
wish to end this feature.
6 *: Select  “AM ” or  “PM ”.
7 MSAVE N a  M OFF N
*1 KX-TGE470 series: page 4
Changing the start and end time
1 For handset setting:  M MENU N#237
For base unit setting (using a
handset) *1
: M MENU N#*237
2 Continue from step 3, “Turning silent
mode on/off”, page 47.
*1 KX-TGE470 series: page 4
Selecting groups to bypass silent
mode
1 For handset setting:  M MENU N#241
For base unit setting (using a
handset) *1
: M MENU N#*241
2 Mb N: Select the desired groups.  a
M SELECT N
R “
” is displayed next to the selected
group numbers.
R To cancel the selected group:
Mb N: Select the group.  a Press
M SELECT N again. “
” disappears.
3 MSAVE N a  M OFF N
*1 KX-TGE470 series: page 4
Baby monitor
This feature allows you to listen in on a room
where another handset is located, allowing
you to easily monitor from different areas of
the house or even while away from home. The
monitored handset (placed in a baby’s room,
for example) will automatically call the
monitoring handset, base unit, or the phone
number stored when it detects sound.
Important:
R Before using this feature, we recommend
that you test this feature and adjust the
baby monitor sensitivity as needed,
especially if you plan to monitor from
outside.
R This feature should not be used as a
substitute for a medical or caregiver’s
supervision. It is the caregiver’s
responsibility to stay close enough to
handle any eventuality.
Note:
R If the unit is connected to a PBX system,
you cannot set the baby monitor.
R During the monitoring mode, battery
consumption is faster than usual. We
recommend leaving the monitored handset
on the base unit or charger.
R The monitored handset never rings while it
is being monitored. If the base unit is
placed near the monitored handset, we
recommend turning off the base unit ringer
volume (page 40, 42).
Setting the baby monitor
Perform the setting operation with the handset
to be monitored (for example, the handset
placed in a baby’s room).
To monitor with a unit
The internal baby monitor feature is available:
– between handsets
– between a handset and the base unit *1
*1 KX-TGE470 series: page 4
1 MMENU N#268
2 Mb N:  “On ” a  M SELECT N
For assistance, please visit http://shop.panasonic.com/support47
Programming

TGE46x47x(en)_1117_ver061.pdf   472015/11/17   15:14:15   
						

							
3Mb N: Select the desired unit’s number to
monitor with.  a M SAVE N
R “Baby monitor ” will be displayed.
R The registered unit’s name/number is
displayed.
Note:
R When this feature is on, another handset or
the base unit can hear the monitored
handset by making an intercom call.
To monitor from outside
If you enable this feature, the unit will call a
pre-programmed phone number when the
handset detects sound. After you answer the
call, you can listen in on the room where the
handset is located.
This feature is only available for landline.
nFrom the phonebook:
1 MMENU N#268
2 Mb N:  “On ” a  M SELECT N
3 Mb N: Select  “Outgoing call ” to
monitor from outside.  a M ADD N
4 Mb N:  “Phonebook ” a  M SELECT N
5 Mb N: Select the phonebook entry.  a
M SAVE N
R “Baby monitor ” will be displayed.
Note:
R If you edit a phonebook entry which is
assigned for monitoring, the edited entry
does not transfer to the monitor.
n By entering phone numbers:
1 MMENU N#268
2 Mb N:  “On ” a  M SELECT N
3 Mb N: Select  “Outgoing call ” to
monitor from outside.  a M ADD N
4 Mb N:  “Manual ” a  M SELECT N
5 Enter the desired name.  a M OK N
6 Enter the desired number.  a M OK N
a  M SELECT N
R “Baby monitor ” will be displayed.
Note:
R The registered name/number is displayed.
Turning off the baby monitor
The monitored handset cannot be used while
baby monitor is set to  “On ”.
1 Press  MMENU N on the handset being
monitored.
2 Mb N:  “On/Off ” a  M SELECT N
3 Mb N:  “Off ” a  M SELECT N a  M OFF N
Editing an outside monitoring number
1 Press  MMENU N on the handset being
monitored.
2 Mb N:  “On/Off ” a  M SELECT N
3 Mb N:  “On ” a  M SELECT N
4 Mb N: Select the outside line.
5 MMENU N a  M b N:  “Edit ” a  M SELECT N
6 Edit the name if necessary.  a M OK N
7 Edit the phone number if necessary.  a
M OK N a  M SELECT N
Erasing an outside monitoring
number
1Press  MMENU N on the handset being
monitored.
2 Mb N:  “On/Off ” a  M SELECT N
3 Mb N:  “On ” a  M SELECT N
4 Mb N: Select the outside line.
5 MMENU N a  M b N:  “Erase ” a  M SELECT N
6 Mb N:  “Yes ” a  M SELECT N a  M OFF N
Baby monitor sensitivity
You can adjust the sensitivity of the baby
monitor. Increase or decrease the sensitivity to
adjust the sound level needed to trigger the
baby monitor feature.
RThis feature cannot be set during a
monitoring call.
1 Press  MMENU N on the handset being
monitored.
2 Mb N:  “Sensitivity level ” a
M SELECT N
48For assistance, please visit http://shop.panasonic.com/support
Programming

TGE46x47x(en)_1117_ver061.pdf   482015/11/17   15:14:15 
						

							
3Mb N: Select the desired setting.  a
M SAVE N a  M OFF N
Answering the baby monitor
nWhen monitoring with a unit:
Handset:  Press M
N to answer a call.
Base unit:  Press MZ N to answer a call. *1
*1 KX-TGE470 series: page 4
If you want to respond from the monitoring
unit, press  MMUTE N.
R The monitoring unit will answer calls
automatically when the auto intercom
feature is set to  “On ” (page 31).
Note:
R If you receive an outside call when
communicating with the monitored
handset, the interrupt tone sounds.
– To answer the call with the handset,
press  MOFF N, then press  M
N.
– To answer the call with the base unit, press  MZ N 3 times. *1
*1 If  MMUTE N is pressed, press  MZ N 2
times.
n When monitoring from outside:
Answer the call.
If you want to respond from your monitoring
phone, press  #1 using tone dialing.
You can turn off the baby monitor feature
by pressing  #0.
Note:
R The unit disconnects the call
automatically after 2 minutes.
Other programming
Changing the handset name
The default handset name is  “Handset 1 ” to
“ Handset 6 ”. You can customize the name
of each handset (“Bob”, “Kitchen”, etc.). This is
useful when you make intercom calls between
handsets. To display the handset name in
standby mode, turn on the handset name
display feature (page 49).
1 MMENU N#104
2Enter the desired name (10 characters
max.).  a M SAVE N a  M OFF N
Displaying the handset name
You can select whether or not the handset
name is displayed in standby mode. The
default setting is  “Off ”.
1 MMENU N#105
2 Mb N: Select the desired setting.  a
M SAVE N a  M OFF N
Registering a unit
Operating additional units
Additional handsets
Up to 6 handsets can be registered to the
base unit.
Important:
R See page 6 for information on the available
model.
Registering a handset to the
base unit
The supplied handset and base unit are
pre-registered. If for some reason the handset
is not registered to the base unit, re-register
the handset.
1 Handset:
MMENU N#130
2 Base unit:
Press and hold  MLOCATOR N or
M HANDSET LOCATOR N for about 5
seconds.
R If all registered handsets start ringing,
press  MLOCATOR N or  MHANDSET
LOCATOR N again to stop, then repeat
this step.
3 Handset:
Press  MOK N, then wait until a long beep
sounds.
For assistance, please visit http://shop.panasonic.com/support49
Programming

TGE46x47x(en)_1117_ver061.pdf   492015/11/17   15:14:15   
						

							
Deregistering a handsetA handset can cancel its own registration to
the base unit, or other handsets registered to
the same base unit. This allows the handset to
end its wireless connection with the system.
1 MMENU N#131
R All handsets registered to the base unit
are displayed.
2 Mb N: Select the handset you want to
cancel.  a M SELECT N
3 Mb N:  “Yes ” a  M SELECT N a  M OFF N
50For assistance, please visit http://shop.panasonic.com/support
Programming

TGE46x47x(en)_1117_ver061.pdf   502015/11/17   15:14:15