Panasonic Kx Tg6311 Operating Instructions Manual

							Preparation
11For assistance, please visit http://www.panasonic.com/help
Handset
ASpeaker
B{MENU}
CSoft keys
D{C} (TALK)
E{s} (SP-PHONE: Speakerphone)
FDial keypad 
({*}: TONE)
G{FLASH} {CALL WAIT}
HCharge indicator
Ringer indicator
Message indicator
IReceiver
JDisplay
K{OFF}
LNavigator key ({^}/{V}/{})
? (Volume: {^}/{V})
M{PAUSE} {REDIAL}
N{HOLD} {INTERCOM}
OMicrophone
PCharge contacts
Using the navigator key
The handset navigator key can be used 
to navigate through menus and to select 
items shown on the display by pressing 
{^}, {V}, {}.
To adjust the receiver or speaker 
volume, press {^} to increase the 
volume, or press {V} to decrease the 
volume repeatedly while talking.
Soft keys
The handset features 2 soft keys. By 
pressing a soft key, you can select the 
feature shown directly above it on the 
display.
Display
Handset display items
A
I
J
L
M
C
K
H
N
O
P
B
C
G
F
D
E
ItemMeaning
5Battery level
[1]Handset number
Line in 
useSomeone is using the 
line.
{V} {^}
{}
Volume downVolume up
 View     PhoneKCID      book L
TG63xx_OI.book  Page 11  Thursday, January 10, 2008  9:02 AM 
						

							Preparation
12For assistance, please visit http://www.panasonic.com/help
Connections
Connect the AC adaptor cord (A) by 
pressing the plug firmly (B). Connect 
the telephone line cord until it clicks into 
the base unit and telephone line jack 
(C).
Base unit
LUse only the supplied Panasonic AC 
adaptor PQLV207.
LUse only the supplied telephone line 
cord. Using another telephone line 
cord may not allow the unit to work 
properly.
Charger
LUse only the supplied Panasonic AC 
adaptor PQLV209.Note:
LThe AC adaptor must remain 
connected at all times. (It is normal for 
the adaptor to feel warm during use.)
LThe AC adaptor should be connected 
to a vertically oriented or floor-
mounted AC outlet. Do not connect 
the AC adaptor to a ceiling-mounted 
AC outlet, as the weight of the adaptor 
may cause it to become disconnected.
During a power failure
The unit will not work during a power 
failure. We recommend connecting a 
corded-type telephone (without AC 
adaptor) to the same telephone line or to 
the same telephone line jack using a 
Panasonic T-adaptor (page 6). 
Emergency power can be supplied to the 
unit by connecting a Panasonic battery 
back-up power supply noted on page 6.
If you subscribe to a DSL/ADSL 
service
Please attach a DSL/ADSL filter (contact 
your DSL/ADSL provider) to the 
telephone line between the base unit 
and the telephone line jack in the event 
of the following:
– noise is heard during conversations.
– Caller ID features do not function 
properly. Available for:
KX-TG6312/KX-TG6313/
KX-TG6322/KX-TG6323/KX-TG6324
(120 V AC, 
60 Hz) To single-line 
telephone jack 
(RJ11C)
A C
Hook
B
A(120 V AC, 60 Hz)
B
HooksTo single-line
telephone 
jack (RJ11C)
DSL/ADSL filter
TG63xx_OI.book  Page 12  Thursday, January 10, 2008  9:02 AM 
						

							Preparation
13For assistance, please visit http://www.panasonic.com/help
Battery installation and 
replacement
Important:
LUse the supplied rechargeable 
batteries (Part No. HHR-65AAABU).
LWhen installing the batteries:
– Wipe the battery ends (S, T) with 
a dry cloth.
– Avoid touching the battery ends 
(S, T) or the unit contacts.
– Ensure correct polarites (S, T).
LWhen replacing the batteries:
– USE ONLY rechargeable Ni-MH 
batteries AAA (R03) size.
– Do NOT use 
Alkaline/Manganese/Ni-Cd 
batteries.
– We recommend using the 
Panasonic rechargeable batteries 
noted on page 6, 8.
1Press the notch on the handset 
cover firmly, and slide it in the 
direction of the arrow.
2Insert the batteries negative (T) 
end first. Close the handset cover.Note:
LWhen replacing batteries, remove the 
old batteries.
Attention:
A nickel metal hydride battery that is 
recyclable powers the product you have 
purchased.
Please call 1-800-8-BATTERY (1-800-
822-8837) for information on how to 
recycle this battery.
Rechargeable Ni-MH ONLY
TG63xx_OI.book  Page 13  Thursday, January 10, 2008  9:02 AM 
						

							Preparation
14For assistance, please visit http://www.panasonic.com/help
Battery charge
Place the handset on the base unit or 
charger for about 7 hours before 
initial use.
LWhile charging, “Charging” is 
displayed and the charge indicator on 
the handset lights up. When the 
batteries are fully charged, “Charge 
completed” is displayed.
*1 KX-TG6312/KX-TG6313/
KX-TG6322/KX-TG6323/
KX-TG6324
Note:
LIt is normal for the handset to feel 
warm during charging.
LIf you want to use the handset 
immediately, charge the batteries for 
at least 15 minutes.
LClean the charge contacts of the 
handset, base unit, and charger with a 
soft and dry cloth once a month. Clean 
more often if the unit is exposed to 
grease, dust, or high humidity.
Battery level
Note:
LKX-TG6311/KX-TG6312/KX-TG6313
The batteries need to be charged if 
the handset beeps while you are 
engaged in a call.
LKX-TG6322/KX-TG6323/KX-TG6324
The batteries need to be charged if 
the handset beeps while you are 
engaged in a call or operating the 
answering system remotely.
Panasonic Ni-MH battery 
performance (supplied batteries)
Note:
LActual battery performance depends 
on a combination of how often the 
handset is in use and how often it is 
not in use (standby).
LEven after the handset is fully 
charged, the handset can be left on 
the base unit or charger without any ill 
effect on the batteries. Base unit: Charger
*1:
Battery iconBattery level
5High
6Medium
7Low
LWhen flashing: 
Needs to be 
charged.
8Empty
OperationOperating time
In continuous 
use5 hours max.
Not in use 
(standby)11 days max.
While using the 
clarity booster 
feature (page 
19)3 hours max.
TG63xx_OI.book  Page 14  Thursday, January 10, 2008  9:02 AM 
						

							Preparation
15For assistance, please visit http://www.panasonic.com/help
LThe battery level may not be 
displayed correctly after you replace 
the batteries. In this case, place the 
handset on the base unit or charger 
and let it charge for at least 7 hours.
Symbols used in these 
operating instructions
Setting up the unit 
before use
Display language
You can select either “English” or 
“Español” as the display language. 
The default setting is “English”.
1{MENU} i {#}{1}{1}{0}
2{V}/{^}: Select the desired setting.
3Press the right soft key to save. i 
{OFF}
Voice guidance language
You can select either “English” or 
“Español” as the voice guidance 
language of the answering system. The 
default setting is “English”.
1{MENU} i {#}{1}{1}{2}
2{V}/{^}: Select the desired setting.
3{Save} i {OFF}
SymbolMeaning
{}The words in the 
brackets indicate 
button names/soft key 
names on the handset 
and base unit.
Example:
Unit keys: {C}, {OFF} 
Soft keys: {View CID}, 
{Phonebook}
iProceed to the next 
operation.
“”The words in 
quotations indicate the 
menu on the display.
Example: “Alarm”
{V}/{^}:
“”Press {V} or {^} to 
select the words in 
quotations.
Example:
{V}/{^}: “Off”
Available for:
KX-TG6322/KX-TG6323/KX-TG6324
TG63xx_OI.book  Page 15  Thursday, January 10, 2008  9:02 AM 
						

							Preparation
16For assistance, please visit http://www.panasonic.com/help
Dialing mode
If you cannot make calls, change this 
setting according to your telephone line 
service. The default setting is “Tone”.
“Tone”: For tone dial service.
“Pulse”: For rotary/pulse dial service.
1{MENU} i {#}{1}{2}{0}
2{V}/{^}: Select the desired setting.
3{Save} i {OFF}
Date and time
1
{MENU} i {#}{1}{0}{1}
2Enter the current month, date, and 
year by selecting 2 digits for each.
Example:July 15, 2008
{0}{7} {1}{5} {0}{8}
3Enter the current hour and minute 
(12-hour clock format) by selecting 2 
digits for each.
Example:9:30
{0}{9} {3}{0}
4{AM/PM}: Select “AM” or “PM”.
5{Save} i {OFF}
Note:
LWhen English is selected as the 
display language, 12-hour clock 
format is used. When Spanish is 
selected, 24-hour clock format is 
used.
LTo correct a digit, press {^}, {V}, {} to move the cursor to the digit, 
then make the correction.
LThe date and time may be incorrect 
after a power failure. In this case, set 
the date and time again.
TG63xx_OI.book  Page 16  Thursday, January 10, 2008  9:02 AM 
						

							Making/Answering Calls
17For assistance, please visit http://www.panasonic.com/help
Making calls
1Lift the handset and dial the phone 
number.
LTo correct a digit, press {Clear}.
2Press {C} or {Call}.
3When you finish talking, press 
{OFF} or place the handset on the 
base unit or charger.
Using the speakerphone
1Dial the phone number, and press 
{s}.
LSpeak alternately with the other 
party.
2When you finish talking, press 
{OFF}.
Note:
LFor best performance, use the 
speakerphone in a quiet environment.
LTo switch back to the receiver, press 
{C}.
Adjusting the receiver or speaker 
volume
Press {^} or {V} repeatedly while 
talking.
Making a call using the redial list
The last 5 phone numbers dialed are 
stored in the redial list (each 48 digits 
max.).
1{REDIAL}
2{V}/{^}: Select the desired phone 
number.
3{C}
Erasing a number in the redial list
1{REDIAL}
2{V}/{^}: Select the desired phone 
number.
3{Erase} i {Ye s} i {OFF}
Pause (for PBX/long distance service 
users)
A pause is sometimes required when 
making calls using a PBX or long 
distance service. When storing a calling 
card access number and/or PIN in the 
phonebook, a pause is also needed 
(page 21).
Example:If you need to dial the line 
access number “9” when making outside 
calls with a PBX:
1{9} i {PAUSE}
2Dial the phone number. i {C}
Note:
LA 3.5 second pause is inserted each 
time {PAUSE} is pressed. Repeat as 
needed to create longer pauses.
Answering calls
When a call is being received, the ringer 
indicator flashes rapidly.
1Lift the handset and press {C} or 
{s} when the unit rings.
LYou can also answer the call by 
pressing any dial key from {0} to 
{9}, {*}, or {#}. (Any key 
answer feature)
2When you finish talking, press 
{OFF} or place the handset on the 
base unit or charger.
Auto talk
You can answer calls simply by lifting the 
handset off the base unit or charger. You 
do not need to press {C}. To turn this 
feature on, see page 24.
TG63xx_OI.book  Page 17  Thursday, January 10, 2008  9:02 AM 
						

							Making/Answering Calls
18For assistance, please visit http://www.panasonic.com/help
Adjusting the handset ringer volume
Press {^} or {V} repeatedly to select the 
desired volume while the handset is 
ringing for an incoming call.
Note:
LYou can also program the handset 
ringer volume beforehand (page 24).
Temporary handset ringer off
While the handset is ringing for a call, 
you can turn the ringer off temporarily by 
pressing {OFF}.
Adjusting the base unit ringer volume
Press {^} or {V} repeatedly to select the 
desired volume.
LTo turn the ringer off, press and hold 
{V} until the unit beeps 2 times.
Useful features during 
a call
Hold
This feature allows you to put an outside 
call on hold.
1Press {HOLD} 2 times during an 
outside call.
2To release hold, press {C}.
LAnother handset user can take 
the call by pressing {C}.
Note:
LIf a call is kept on hold for more than 9 
minutes, an alarm tone starts to sound 
and the ringer indicator flashes 
rapidly. After 1 additional minute on 
hold, the call is disconnected.LIf another phone is connected to the 
same line (page 12), you can also take 
the call by lifting its handset.
Mute
While mute is turned on, you can hear 
the other party, but the other party 
cannot hear you.
1Press {Mute} during an outside call.
L{Mute} flashes.
2To return to the conversation, press 
{Mute} again.
Note:
L{Mute} is a soft key visible on the 
handset display during a call.
Flash
{FLASH} allows you to use the special 
features of your host PBX such as 
transferring an extension call, or 
accessing optional telephone services. 
Note:
LTo change the flash time, see page 
25.
For call waiting or Call Waiting 
Caller ID service users
To use call waiting, you must first 
subscribe to the call waiting service of 
your service provider/telephone 
company.
This feature allows you to receive calls 
while you are already talking on the 
phone. If you receive a call while on the 
phone, you will hear a call waiting tone.
If you subscribe to both Caller ID and 
Call Waiting with Caller ID services, 
the 2nd caller’s information is displayed 
after you hear the call waiting tone on the 
handset.
1Press {CALL WAIT} to answer the 
2nd call. Available for:
KX-TG6322/KX-TG6323/KX-TG6324
TG63xx_OI.book  Page 18  Thursday, January 10, 2008  9:02 AM 
						

							Making/Answering Calls
19For assistance, please visit http://www.panasonic.com/help
2To switch between calls, press 
{CALL WAIT}.
Note:
LPlease contact your service 
provider/telephone company for 
details and availability of this service 
in your area.
Temporary tone dialing (for 
rotary/pulse service users)
You can temporarily switch the dialing 
mode to tone when you need to access 
touch-tone services (for example, 
answering services, telephone banking 
services, etc.).
Press {*} (TONE) before entering 
access numbers which require tone 
dialing.
Handset clarity booster
This feature can improve sound clarity 
when the handset is used in an area 
where there may be interference. During 
an outside call, this feature is turned on 
automatically when necessary.
LWhen this feature is turned on, 
“BOOST” flashes.
LWhile this feature is turned on, the 
battery operating time is shortened 
(page 14).
Call share
This feature allows you to join an 
existing outside call.
To join the conversation, press {C} 
when the other handset is on an outside 
call.
Note:
LThe maximum number of participating 
parties (including 1 outside party) 
depends on the model.
– 3 parties (KX-TG6311/
KX-TG6312/KX-TG6313)– 4 parties (KX-TG6322/
KX-TG6323/KX-TG6324)
TG63xx_OI.book  Page 19  Thursday, January 10, 2008  9:02 AM 
						

							Shared Phonebook
20For assistance, please visit http://www.panasonic.com/help
Shared phonebook
The shared phonebook allows you to 
make calls without having to dial 
manually. Any handset registered to the 
base unit can use the shared 
phonebook. You can add 50 names and 
phone numbers to the shared 
phonebook.
Important:
LOnly 1 person can access the shared 
phonebook at a time.
Adding entries
1
{Phonebook}
2{Add}
3Enter the party’s name (16 
characters max.). i {Next}
4Enter the party’s phone number (32 
digits max.). i {Next} i {Save}
LTo add other entries, repeat from 
step 2.
5{OFF}
Note:
LCaller ID subscribers can use ringer 
ID feature (page 29).
Character table for entering namesLTo enter another character that is 
located on the same dial key, first 
press {>} to move the cursor to the 
next space.
Correcting a mistake
Press {} to move the cursor to 
the character or number you want to 
erase, then press {Clear}. Enter the 
appropriate character or number.
LPress and hold {Clear} to erase all 
characters or numbers.
Finding and calling a 
phonebook entry
Scrolling through all entries
1{Phonebook} i {Search}
2{V}/{^}: Select the desired entry.
3{C}
Searching by first character 
(alphabetically)
1{Phonebook} i {Search}
2Press the dial key ({0} – {9}, {*}, 
or {#}) which contains the 
character you are searching for 
(page 20).
LPress the same dial key 
repeatedly to display the first 
entry corresponding to each 
character located on that dial key.
LIf there is no entry corresponding 
to the character you selected, the 
next entry is displayed.
3{V}/{^}: Scroll through the 
phonebook if necessary.
4{C}
KeyCharacter
{1}&’ (),–./1
{2}a b c ABC2
{3}def DEF3
{4}ghi GHI 4
{5}jklJKL5
{6}mn o MN O 6
{7}pqr sPQRS7
{8}tuvTUV8
{9}wx y z WX YZ 9
{0}0Space
{*} ;
{#}#
KeyCharacter
TG63xx_OI.book  Page 20  Thursday, January 10, 2008  9:02 AM