Panasonic Kx Tg5200 Operating Instructions Manual

							Useful Information Answering System Telephone System
11
Installation
For assistance, please call: 1-800-211-PANA(7262)
Preparation
Installing the Battery in the Handset
Insert the battery (1), and press it down until it snaps into the compartment (2). 
Close the cover.
To replace the battery:
Press the notch on the cover firmly and slide it as 
indicated by the arrow. Replace the old battery with a new 
one (p. 12). Close the cover and charge the handset for 6 
hours.
Battery Charge
Place the handsets on the base 
unit and charger for 6 hours 
before initial use.
•The unit beeps once, the CHARGE 
indicator lights and “Charging” is 
displayed. 
•When the battery is fully charged, 
“Charge completed” is displayed 
if there are no new calls in the Caller 
List.
 
Battery strength
You can confirm the battery 
strength on the handset 
display.
Battery strength is indicated 
by the icons shown in the 
chart to the right.Display promptBattery strength
 
1Fully charged
 Medium
 
3Low
(flashing) Needs to be recharged.
 
4Discharged
1
2
CHARGE Indicator(KX-TG5202 only)
AND
2
3 
						

							Installation
12
Recharge
Recharge the battery when:
— “Recharge battery” is displayed on the handset,
— “
3” flashes, or
— the handset beeps intermittently while it is in use.
•The display will continually indicate “Recharge battery” and/or “
3” will 
flash when the handset battery is charged for less than 15 minutes and the 
handset is lifted off the base unit or charger.
•If the battery has been discharged, the handset will display “Charge for 6 HRS” 
and “
4” when you place the handset on the base unit or charger. The handset 
will not work unless the battery is charged. Continue charging.
A nickel metal hydride battery that is recyclable powers the product 
you have purchased. Please call 1-800-8-BATTERY for 
information on how to recycle this battery
.
Battery information
After your Panasonic battery is fully charged, you can expect the following performance:
•A fully charged battery will give you up to 5 hours of continuous talk time, or keep 
your handset in Standby mode to receive incoming calls for up to 11 days (if no 
phone calls are made). Battery power is consumed whenever the handset is off of 
the base unit or charger, even when the handset is not in use. The longer you 
leave the handset off of the base unit or charger, the time you can actually talk on 
the handset will be shortened. Actual battery performance depends on a 
combination of how often the handset is in TALK mode and how often it is in 
Standby mode.
• Clean the charge contacts of the handset, the base unit and charger with a 
soft, dry cloth once a month. Clean more often if the unit is subject to 
grease, dust or high humidity. Otherwise the battery may not charge properly.
•If the battery is fully charged, you do not have to place the handset on the base 
unit or charger until “Recharge battery” is displayed and/or “
3” flashes. 
This will maximize the battery life.
•
If you want to keep the battery fully charged at all times, place the handset on the base 
unit or charger when the handset is not used. The battery cannot be overcharged.
•When the Clarity Booster feature is turned on automatically or manually, battery 
operating time may be shortened (p. 22).
Battery replacement:
If you cleaned the charge contacts and fully charged the battery, but after a few 
telephone calls, “Recharge battery” is displayed and/or “
3” continues to 
flash, or “Charge for 6 HRS” and “
4” are displayed, the battery may need 
to be replaced. Please order a new Panasonic HHR-P104 battery at the 
telephone number shown on page 2. To replace the battery, see page 11.
OperationOperating time
While in use (TALK) Up to 5 hours
While not in use (Standby) Up to 11 days
While using the Clarity Booster feature (p. 22) Up to 3 hours
 SPIPRIVACY3
Recharge battery
IN USE[1] 
						

							Useful Information Answering System Telephone System
13For assistance, please call: 1-800-211-PANA(7262)
Preparation
Programmable Settings
Programming Guidelines 
The unit has several programmable functions which can be selected from the 
function menu on the display (p. 14).
How to select a function item from the menu
•To go back to the previous menu, press the soft key ( ), or press the soft key 
() while “---(Go back)----” is displayed. If you press this key in the 
main menu, the unit will exit programming mode.
•After programming is complete, the display will return to the main menu or the 
sub-menu depending on which menu the selected item is located. (See the menu 
table on page 14.)
•You can exit programming mode at any time by pressing [OFF]. 
•
If you do not press any buttons for 60 seconds, the unit will exit programming mode.
•If the unit detects a problem, an error message will be displayed (p. 55–56) and/or 
error beeps will sound.
Make sure the handset and base unit are not being used. The handset must 
be operated near the base unit and while off the base unit or charger.
1Press [MENU].
•The main menu is displayed (p. 14).
2Scroll to the desired item by pressing [d] or [B]. 
3Press the soft key ( ) to select the desired item. 
4If the item has a sub-menu, select the menu item (p. 14). 
Repeat steps 2 and 3 until the desired item is displayed. 
If the item has no sub-menu, go to step 5.
5Select the desired setting by pressing [d] or 
[B], then press the soft key ( ).
•A confirmation tone will be heard and the setting 
will be saved. 
6Press [OFF] to exit programming mode.
Handset
   SAVE      SAVE         BACKBACKSAVE
[OFF] exits 
programming.
Navigator key scrolls  
through the menu.[MENU] enters the  
function menu.The soft key works as
the             or           key.
The soft key works
as the           key.
BACKSAVESELECT
       B
Ringer setting
       d  BACKPLAYSELECT
SELECT
SAVEdB  BACKPLAYSAVE
BACK
SELECT 
						

							Programmable Settings
14
Function Menu Table 
You can use the following functions to customize your unit. See the corresponding 
pages for function details.
•After pressing [MENU], you can also program menu items directly by pressing ([0] 
to [9], and [#]) instead of using the soft keys (p. 51–52).
•If you program the Voice Mail (VM) access number, Voice Mail (VM) tone 
detection, dialing mode, flash time or line mode using one of the handsets, you will 
not need to program the same item using another handset.
Handset
Ringer volume
Ringer tone
Incoming call.
View Info.?
Get new Info.?
Voice Mail
LCD contrast
Key tone
Auto talk
Set flash time
Set line mode
RegistrationHS registration
Deregistration
*
Message alert
Turn CIQ off?
Set dial mode
Change languageDisplay
Main menuSub-menu I
Caller IQ
Initial setting
Sub-menu II
Voice enhancer
Copy 1 item
Copy all items
Copy phone book
Ringer setting
Store VM access#
VM tone detect
Caller ID edit
Set tel line
p. 64
p. 63
p. 61*“Activate CIQ?” is 
displayed if you have 
not subscribed to 
openLCR service.
“Turn CIQ on?” is 
displayed when Caller 
IQ is turned off (p. 61).
p. 22p. 17
p. 18
p. 46
p. 35
p. 36
p. 16
p. 28
p. 15p. 19
p. 19
p. 46p. 40
p. 41
p. 53
p. 52 p. 15
p. 45
p. 16 
						

							Useful Information Answering System Telephone System
15
Programmable Settings
For assistance, please call: 1-800-211-PANA(7262)
Preparation
Display Language 
You can select either “English” or “Spanish” as the display language. The factory 
preset is “English”.
•If you select a language you cannot read, change the display language again 
using direct commands (p. 51).
Dialing Mode 
If you have touch tone service, set the dialing mode to “Tone”. For rotary or pulse 
service, set to “Pulse”. The factory preset is “Tone”.
1Press [MENU].
2Scroll to “Initial setting” by pressing 
[d] or [B], then press the soft key ( ). 
3Scroll to “Change language” by pressing 
[d] or [B], then press the soft key ( ). 
4To change from English to Spanish, press the 
soft key ( ). 
To change from Spanish to English, press the 
soft key ( ).
•The display changes to the selected language.
•You can also select the display language by 
pressing [d] or [B].
5When Spanish is selected, press the soft key ( ), then press [OFF].
When English is selected, press the soft key ( ), then press 
[OFF].
1Press [MENU].
2Scroll to “Initial setting” by pressing 
[d] or [B], then press the soft key ( ). 
3Scroll to “Set tel line” by pressing [d] or 
[B], then press the soft key ( ).
4Press the soft key ( ) at “Set dial 
mode”. 
5Select “Pulse” or “Tone” by pressing [d] or 
[B].
6Press the soft key ( ), then press [OFF].
Handset
SELECTInitial setting
SELECTChange language
ESPAÑOL
ENGLISH
Display
:English
GUARDAR
SAVE
Handset
SELECTInitial setting
SELECTSet tel line
SELECTSet dial mode
Set dial mode
:Tone
SAVE 
						

							Programmable Settings
16
Line Mode 
The line mode is preset to “B” and generally should not be adjusted. If “  ” is 
not displayed on the handset properly, the line mode selection is incorrect. Set line 
mode to 
“A”.
Auto Talk 
The Auto Talk feature allows you to answer calls by simply lifting the handset off the 
base unit or charger (for KX-TG5202 or accessory handset users, p. 3). You do not 
need to press [C] or [s]. The factory preset is OFF.
•In order to view Caller ID information after you lift the handset to answer a call, 
leave the Auto Talk feature turned off.
1Press [MENU].
2Scroll to “Initial setting” by pressing 
[d] or [B], then press the soft key ( ). 
3Scroll to “Set tel line” by pressing [d] or 
[B], then press the soft key ( ).
4Scroll to “Set line mode” by pressing [d] 
or [B], then press the soft key ( ).
5Select “A” or “B” by pressing [d] or [B].
6Press the soft key ( ), then press [OFF].
1Press [MENU].
2Scroll to “Initial setting” by pressing 
[d] or [B], then press the soft key ( ). 
3Scroll to “Auto talk” by pressing [d] or 
[B], then press the soft key ( ).
4Select “On” or “Off” by pressing [d] or [B].
5Press the soft key ( ), then press [OFF].
Handset
IN USE
SELECTInitial setting
SELECTSet tel line
SELECTSet line mode
Set line mode
:B
SAVE
Handset
SELECTInitial setting
SELECTAuto talk
Auto talk
:Off 
SAVE 
						

							Useful Information Answering System Telephone System
17
Programmable Settings
For assistance, please call: 1-800-211-PANA(7262)
Preparation
Ringer Volume 
You can set the handset ringer volume to high, medium, low, or off. The factory 
preset is HIGH. If set to off, the handset will ring at the low level for intercom calls, 
and will not ring for outside calls. 
•If the handset ringer is turned off, the handset displays “Ringer off” while not in 
use. When there are new messages in your voice mailbox (p. 42), “Ringer off” 
is not displayed.
•
You can also adjust the ringer volume while an outside call is ringing. Press [d] or 
[B] while the handset is ringing. 
Temporary ringer off
While the handset is ringing for an outside call, you can turn the ringer off 
temporarily by pressing [OFF]. The handset will ring again as normal the next time 
a call is received.
1Press [MENU].
2Press the soft key ( ) at “Ringer 
setting”.
3Press the soft key ( ) at “Ringer 
volume”. 
4Select the desired volume by pressing [d] or 
[B].
•The volume will change and ring.
•The number of steps indicates the volume level.
• To turn the ringer off, press [d] repeatedly until 
“Off ?” is displayed.
5Press the soft key ( ).
Handset
SELECTRinger setting
SELECTRinger volume
Ringer volume
 Low   High
Ex. High
Ringer volume
       Off ?
Ex. Off
SAVE 
						

							Programmable Settings
18
Ringer Tone 
You can set the handset ringer to use one of 7 ringer patterns for outside calls. 
“Tone 1” to “Tone 3” are bell ringer patterns. “Melody 1” to “Melody 4” are preset 
melody patterns. The factory preset is “Tone 1”. 
•You cannot change the ringer tone for intercom calls.
•If you subscribe to a Distinctive Ring Service (such as IDENTA-RING) from your 
telephone company with 2 or 3 consecutive rings, select a bell ringer pattern (Tone 
1 to 3). If you select a melody pattern, you will not be able to distinguish lines by 
their ringers.
•If you select one of the melody ringer patterns, the ringer will continue to sound for 
several seconds if:
— the caller hangs up before you answer the call, or
—
another person answers the call using another phone connected on the same 
line.
1Press [MENU].
2Press the soft key ( ) at “Ringer 
setting”.
3Scroll to “Ringer tone” by pressing [d] or 
[B], then press the soft key ( ).
4Select the desired ringer tone by pressing 
[d] or [B].
•The handset will ring and the ringer tone will 
change. If the ringer volume has been turned off, 
the handset will not ring (p. 17).
•You can also select the ringer tone by pressing 
[1] to [7].
5Press the soft key ( ), then press [OFF].
Handset
SELECTRinger setting
SELECTRinger tone
Ringer tone
1 :Tone 1
SAVE 
						

							Useful Information Answering System Telephone System
19
Programmable Settings
For assistance, please call: 1-800-211-PANA(7262)
Preparation
LCD Contrast 
There are 6 levels of LCD contrast. The factory preset is “level 3”.
Message Alert 
You can select whether or not the Ringer/Message Alert indicator on the handset 
will flash slowly when new messages in your voice mailbox have been recorded 
(p. 42). The factory preset is OFF.
•The Ringer/Message Alert indicator will not flash for new messages while the 
handset is in use.
•The Ringer/Message Alert indicator acts as a ringer indicator and as a message 
alert indicator. This indicator will flash rapidly when a call is received whether this 
feature is on or off.
•Battery operating time may be shortened when using this feature (p. 12).
1Press [MENU].
2Scroll to “Initial setting” by pressing 
[d] or [B], then press the soft key ( ). 
3Scroll to “LCD contrast” by pressing [d] or 
[B], then press the soft key ( ).
4Select the desired contrast by pressing [d] 
or [B].
•The contrast will change.
•The number of steps indicates the contrast level.
5Press the soft key ( ), then press [OFF].
1Press [MENU].
2Scroll to “Initial setting” by pressing 
[d] or [B], then press the soft key ( ). 
3Scroll to “Message alert” by pressing [d] 
or [B], then press the soft key ( ).
4Select “On” or “Off” by pressing [d] or [B].
5Press the soft key ( ), then press [OFF].
Handset
SELECTInitial setting
SELECTLCD contrast
LCD contrast
 Low      High
Ex. Level 3
SAVE
Handset
SELECTInitial setting
SELECTMessage alert
Message alert
:Off
SAVE 
						

							20
Making Calls 
System capabilities (Operating more than one handset, p. 3)
Up to 2 handsets can operate at a time. The maximum operating number may 
decrease depending on the state of use.
1Press [C].
•“Talk” is displayed.
2Dial a phone number.
•The dialed number is displayed.
•After a few seconds, the display will 
show the length of the call.
3To hang up, press [OFF] or place 
the handset on the base unit or 
charger (for KX-TG5202 or 
accessory handset users, p. 3).
To have a hands-free phone 
conversation
1
Press [s].
•“SP-phone” is displayed.
2Dial a phone number.
•The dialed number is displayed.
•After a few seconds, the display will 
show the length of the call.
3When the other party answers, talk 
into the microphone.
4To hang up, press [OFF] or place 
the handset on the base unit or 
charger.
Hands-free Digital Duplex Speakerphone
For best performance, please note the following:
•Talk alternately with the other party in a quiet room.
•If you or the other party has difficulty hearing, press [d] to decrease the 
speaker volume.
•While talking using [C], you can switch to a hands-free phone conversation 
by pressing [s]. To switch back to the receiver, press [C].
[REDIAL] [   ] [    ]
[OFF]
Soft Keys
[HOLD/INTERCOM]
Microphone
[B], [d]